Related Manuals for Bowflex BodyTower
Summary of Contents for Bowflex BodyTower
- Page 1 ® ® Bowflex BodyTower ® ™ Assembly Manual Manual en Español Latino Americano: http://www.bowflex.com...
-
Page 2: Table Of Contents
Printed in China | © 2011 Nautilus, Inc., All rights reserved. ™ and ® indicate a trademark or registered trademark. Nautilus, Inc. (www.NautilusInc.com) trademarks include NAUTILUS®, BOWFLEX®, SCHWINN® and UNIVERSAL® and respective logos. Other trademarks are the property of their respective owners. -
Page 3: Important Safety Instructions
Important Safety Instructions This icon means a potentially hazardous situation which, if not avoided, could result in death or serious injury. Before using this equipment, obey the following warnings: Read and understand all warnings on this equipment. Carefully read and understand the Assembly Manual. •... -
Page 4: Specifications
Specifications 76.9” 195.4 cm 49.7” 51.2” 126.3 cm 130.1 cm Before Assembly Select the area where you are going to set up and operate your equipment. For safe operation, the location must be on a hard, level surface. Allow a workout area of minimum 123” x 123” (3.1m x 3.1m). Follow these basic points when you assemble your equipment: 1. -
Page 5: Parts
Parts Ref. Qty Description Ref. Qty Description Base Cross Brace E-Z Adjust Arm, Left Base Frame, Left E-Z Adjust Arm, Right Base Frame, Right Pull Up Bar Upright Exercise Placard Backbone Handgrip Back Pad Assembly Sling Strap... -
Page 6: Hardware
Hardware Guide Ref. Qty Description Ref. Qty Description Button Head Hex Screw M8 X 35 Lock Washer M8 Carriage Bolt M8 X 55 Flat Washer M8 Button Head Hex Screw M8 X 60 Flat Washer M10 Carriage Bolt M10 X 55 Acorn Nut M10 Acorn Nut M8 Lock Washer M10... -
Page 7: Assembly Steps
Assembly Steps Step 1: Attach Base Cross Brace to Base Frames Note: Do not tighten the hardware until the parts of the base are together. Make sure that the square on the bolt is in the square hole (1a) on the Base Cross Brace. Do not install the hardware that joins the left and right Base Frames at this time. - Page 8 Assembly Steps Step 2: Attach Uprights to Cross Brace Note: Do not completely tighten the hardware at this time.
- Page 9 Assembly Steps Step 3: Attach E-Z Adjust Arms to Back Pad Assembly...
- Page 10 Assembly Steps Step 4: Install the E-Z Adjust Bar Assembly on the Uprights Remove the Locking Pins (7a) from E-Z Adjust brackets before you install the assembly on the Uprights. Tilt the assembly to put it on the Uprights. If necessary, remove end caps from the Uprights.
- Page 11 Assembly Steps Step 5: Install the Pull Up Bar to the Uprights Note: Move the E-Z Adjust Bar to the bottom of the Uprights and tighten the hardware at the base of the Uprights completely. Then move the E-Z Adjust Bar to the top of the Uprights and tighten the hardware on the Pull Up Bar.
- Page 12 Assembly Steps Step 6: Install the Backbone to the Pull Up Bar and Base Note: Attach the Backbone to the Pull Up Bar first. For the carriage bolts at the base, you can put a piece of tape on each bolt head to hold it in position during installation. Tighten the outer bolts first.
- Page 13 Assembly Steps Step 7: Install Placard on Backbone...
- Page 14 Assembly Steps Step 8: Attach Handgrips and Sling Straps...
- Page 15 Assembly Steps Step 9: Final Inspection Inspect your equipment to ensure that all fasteners are tight, the equipment is level, and components are properly assembled. Do not use the equipment until the equipment has been fully assembled and inspected for correct performance in accordance with the Owner’s Manual. Note: Record serial number in the Serial Number field at the beginning of the Owner’s Manual.
- Page 16 Nautilus Bowflex Schwinn Fitness Universal ® ® ® ® 004-4693-111811C...
Need help?
Do you have a question about the BodyTower and is the answer not in the manual?
Questions and answers