Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Whirlpool CSP2760TQ0
Summary of Contents for Whirlpool CSP2760TQ0
- Page 1 INSTALLATION INSTRUCTIONS COMMERCIALSTACKEDDRYER Gas (12(!-Volt, 6 0-Hz)or Electric (12(}/24(}-Volt, 60-Hz) Table of Contents ............Actual unit may or may not contain doors with windows depending on model 8577211 www, w hirlpool.com...
-
Page 2: Table Of Contents
TABLEOF CONTENTS DRYER SAFETY ................iNSTALLATiON REQUIREMENTS ..........Location Requirements .............. Tools and Parts ................Electrical Requirements ............Gas Supply Requirements ............Venting Requirements .............. iNSTALLATiON iNSTRUCTiONS - GAS DRYER ....10 install Coin-Slide and Coin Box ..........Make Gas Connection .............. Connect Vent ................ - Page 3 WARNING: For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, or to prevent property damage, personal injury, or death. = Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
-
Page 4: Installation Requirements
INSTALLATION REQUIREMENTS 'iii _ i::_ ¸ 0 !_!i_ iiii_i_ ii _ _i!ii iii J_' _iii _'_i: _!ii_ Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools needed 8" or 10" pipe wrench 8"... -
Page 5: Tools And Parts
Minimum Installation Clearances Product Dimensions Back Sides Front Recessed 0 in 0 in 6 in (0 cm) (0 cm) (15.2 cm) Closet 0 in 0 in 0 in 7 in (0 cm) (0 crn) (0 cm) (17.5 cm) exhaust 0" (0 cm! 13-1/2"... -
Page 6: Electrical Requirements
IMPORTANT: The dryer must be electrically grounded in accordance with local codes and ordinances or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, latest edition. The National Electric Code requires a 4-wire supply connections for homes built after 1996, dryer circuits involved in remodeling after 1996, and all mobile home installations. -
Page 7: Location Requirements
i!!iii,, i:iiiiii (!;z iiF i!!:iiiieqxiiX', !! isesi: Gas Supply Line Recommended method Provide a gas supply line of rA" rigid (IPS) pipe to the dryer location. Pipe joint compounds that resist the action of LP gas must be used. Do not use TEFLON _ tape. With LP gas, piping or tubing size can be 1/2"minimum. -
Page 8: Venting Requirements
Rigid metal vent is recommended to prevent crushing and Whirlpool Service Manual, "Exhausting Whirlpool Dryers," Part kinking. No. LIT603197, available from your Whirlpool parts distributor. Flexible metal vent must be fully extended and supported when If dryer is installed in a confined area, such as a bedroom, the dryer is in its final position. - Page 9 CFM of all the dryers in the room. Back-draft Damper Kits, Part No. 3391910, are available from your Whirlpool dealer and should be installed in each dryer's vent to prevent exhausted air from returning into the dryers and to keep the exhaust in balance within the main vent.
-
Page 10: Installation Instructions - Gasdryer
INSTALLATION INSTRUCTIONS - GASDRYER Secure coin slide mechanism from inside the control panel 9° using the 3/16"bolt and washer included with the slide mechanism. Install coin box. The collar houses the accumulator timer with actuating arm and button. The factory-installed timer is set to provide 45 minutes (4 pins) of drying time when activated by the coin slide. -
Page 11: Installation Instructions =Electricdryer
3. Check dryer operation (some accumulated time may be on the timer due to factory testing). Insert coins in slide and press slide in slowly. (Operating time will accumulate per number of coins and type of timing cam used.) Push START/RESTART button. Using a full heat cycle (not the air cycle), let the dryer run for at least five minutes. -
Page 12: Make Electrical Connection
2. Remove hold-down screw and theterminal block cover. Power Supply Cord Method This dryer is manufactured with the neutral ground wire connected to the neutral (center) of the wiring harness at the terminal block. If local codes do not permit this type of connection, use "Four-wire connection"... - Page 13 Use this method where local codes permit connecting Power Supply Cord, neutral ground wire to neutral wire: A ....Three=wire electrical connection: 5. Loosen or remove the center terminal F-'__ block screw. F ..Connect the neutral wire (white or center) of the power supply cord to the center, silver-colored terminal screw of the ....
- Page 14 A. Extemat ground conductor screw B. Tab Fire Hazard C. Terminal block cover Use 10 gauge solid copper wire. D. Hold-down screw Use a UL listed strain relief. Install 3/4"conduit connector into the hole below the terminal Disconnect power before making electrical block opening•...
-
Page 15: Connect Vent
Direct Wire, Use this method where local codes permit Three=wire electrical connection: connecting neutral ground wire to neutral wire: 5. Loosen or remove the center terminal block screw. 6. Place the hooked end of the neutral wire (white or center) of the direct wire cable under the center screw of the terminal block (hook facing right). -
Page 16: Changing To A 30-Or60-Minute Timingcam
CHANGING TO A 30-OR60-MINUTE TIMINGCAM Insert a narrow, flat-blade screwdriver under the timing cam near the clock shaft. Gently lift cam straight up and off shaft making sure that the V-shaped notch clears the ratchet tooth. _ili.. • Electrical Shock Hazard Disconnect power before making cam changes.