D I S A S S E M B L Y P R O C E D U R E Chapter Disassembly Procedure Please follow the information provided in this section to perform the complete disassembly procedure of the notebook. Be sure to use proper tools described before.
D I S A S S E M B L Y P R O C E D U R E Battery module B A T T E R Y The illustration below shows how to remove the battery module. 1. Turn the notebook over. Unlock one latch (no.1) and remove the battery pack from bottom side (no.2).
Page 3
D I S A S S E M B L Y P R O C E D U R E 2. Turn the notebook over, release one screws K / B C O V E R R E M O V A L 3.
Page 4
D I S A S S E M B L Y P R O C E D U R E 2. Disconnect K/B cable K / B R E M O V A L 2. Cable out 1. Unlock 1. Unlock Lock Lock Removing ROM drive...
D I S A S S E M B L Y P R O C E D U R E Please do not touch inside of the HDD module. CPU Module C P U The illustrations below show how to remove the CPU module from the notebook. The module contains CPU, CPU thermal pad, and CPU thermal module.
Page 7
D I S A S S E M B L Y P R O C E D U R E C P U R E M O V A L 5. Remover CPU VGA CARD REMOVE V G A C A R D 1.
The illustrations below show how to remove the Memory module from the notebook. R E M O V A L The KN1 Series Notebook comes standard without memory onboard. There are two expansion SODIMM sockets for you to upgrade the total memory up to...
Page 9
D I S A S S E M B L Y P R O C E D U R E W / L C A R D W/L CARD REMOVE R E M O V A L 1. Release 1pcs screw, then remove wireless door 2.
D I S A S S E M B L Y P R O C E D U R E LCD module L C D The illustrations below show how to remove and disassemble the LCD module. The module contains LCD panel, inverter board, LCD hinge bracket, hinge cover, LCD bezel and LCD cover.
Page 11
D I S A S S E M B L Y P R O C E D U R E 4. Pull out cable conn L C D R E M O V A L 5. Release se 4pcs screw on the hinge, remove LCD module L C D R E M O V A L Disassembling LCD Module...
Page 12
D I S A S S E M B L Y P R O C E D U R E 3. Remove 14pcs screws and 1pcs screw on the inverter board 4. Disconnect left and right on the inverter boar 2 - 12...
Page 13
D I S A S S E M B L Y P R O C E D U R E 5. Disassemble LCD panel for LCD module, then remove 4pcs screw on the left and right LCD bracket TOP cover module T O P C O V E R The illustrations below show how to disassemble and remove the top cover...
Page 14
D I S A S S E M B L Y P R O C E D U R E 2. Remove 3pcs screw on the top 3. Release touch pad cable 2 - 14...
Page 15
D I S A S S E M B L Y P R O C E D U R E 4. Remove the top cover from left side Removing Motherboard module M / B M O D U L E R E M O V A L 1.
Page 16
D I S A S S E M B L Y P R O C E D U R E 2. Release 2pcs screw on modem board, pull out modem board 3. Disconnect speaker cable conn from motherboard 2 - 16...
Page 17
D I S A S S E M B L Y P R O C E D U R E 5. Remove M/B module carefully pry out left side to remove audio jack first ,then remove IO port from front side to separate the M/B from base module 2 - 17...
Need help?
Do you have a question about the KN1 Series and is the answer not in the manual?
Questions and answers