Lenovo ThinkServer TS430 User Manual
Remote management module
Hide thumbs
Also See for ThinkServer TS430:
- Hardware maintenance manual (264 pages) ,
- Benutzerhandbuch (234 pages) ,
- Manual d'utilisation (230 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Lenovo ThinkServer TS430
Summary of Contents for Lenovo ThinkServer TS430
- Page 1 ThinkServer Remote Management Module User Guide...
- Page 2 “Notices” on page 25. First Edition (June 2011) © Copyright Lenovo 2011. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
-
Page 3: Table Of Contents
Network ....Network Security ... . Chapter 2. Overview of Lenovo Security .... - Page 4 ThinkServer Remote Management Module User Guide...
-
Page 5: Chapter 1. Introduction
Otherwise, it may result in personal injury or equipment damage. Electrostatic Discharge (ESD) and ESD protection: Electrostatic Discharge (ESD) can damage disk drivers, system board and other components. We recommend that you complete all the steps in this Section © Copyright Lenovo 2011... - Page 6 only in the ESD protective workstations. If ESD workstation is unavailable, please wear anti-static wrist strap while holding parts and connect the wrist strap to the ground wire (that is, any unpainted metal surface) of the server chassis to provide ESD protection. ESD and holding system boards: Be careful when holding the system board.
-
Page 7: Chapter 2. Overview Of Lenovo Thinkserver Remote Management Module
Chapter 2. Overview of Lenovo ThinkServer Remote Management Module This section briefly describes the features of the Remote Management Module. The Remote Management Module runs on the server system as an integrated solution and integrates the embedded operating system. Independent of the server operating system, the embedded operating system can provide a whole set of complete, stable and effective solution for the server. - Page 8 ThinkServer Remote Management Module User Guide...
-
Page 9: Chapter 3. Configuration Of Thinkserver Remote Management Module
4. When you finish the configuration, please save the settings. Table 1. IPMI 2.0 Configuration Sub-menu Configuration Source STATIC Static: static IP configuration. IP and the subnet mask can be set manually. DHCP DHCP: dynamic IP configuration. The system can obtain IP automatically. © Copyright Lenovo 2011... - Page 10 ThinkServer Remote Management Module User Guide...
-
Page 11: Chapter 4. Thinkserver Remote Management Module Quick Start
Note: As the supported functions of the product vary with configurations, please refer to the actual product description. For more information about the initial settings, see Section 3.The user name in this Section is “lenovo”. Besides “lenovo”, other usernames and passwords are also accepted. The default user name and password are as follows: •... -
Page 12: Navigation
2. Enter the user name and password. For example: • Username = lenovo • Password = lenovo 3. Click the OK button to view the home page of the Remote Management Module. After a successful initial login, the system administrator can create new users and has full permission of Remote Management Module. -
Page 13: Logout Thinkserver Remote Management Module
Features Event Management By clicking this tab, you can configure various settings of the server. Network Configuration page will automatically show in general, this tab allows accessing the following items: • Platform Events • Trap Settings • Email Settings Serial Over LAN This page provides the serial over LAN settings. - Page 14 ThinkServer Remote Management Module User Guide...
-
Page 15: Chapter 5. Remote Console (Kvm) Operation
View Menu of Remote Console By clicking the View option on the control bar of the remote console, you can select the view option in the menu. With this menu, you can take the following operations: © Copyright Lenovo 2011... -
Page 16: Macros Menu Of The Remote Console
• Hide Status Bar: Hide the KVM status at the bottom of the screen. • Refresh: Refresh the screen. • Full Screen: Switch between the window mode and full screen of the remote console. • Fit: Fit the window mode. Macros Menu of the Remote Console By clicking Macros, you can open the Macros menu containing relevant task options. -
Page 17: Chapter 6. Thinkserver Remote Management Module Web Console Options
If you want to configure the IP by IPv6 protocol, enable IPv6 Settings the IPv6, and set the IP address. VLAN Settings When you enable virtual LAN, you have to set the VLAN ID, Priority also. © Copyright Lenovo 2011... -
Page 18: Network Security
• Must not be the same as the previous 5 passwords. Notes: • The user lenovo and three can not be modified or deleted. • To add a new user, select a blank row from list and click User ID. -
Page 19: Services
User Role Description Operator All BMC commands are allowed, except for configuration commands that can change the behavior of the out-of band interfaces. For example, Operator privilege does not allow the capability to disable individual channels, or change user access privileges. Administrator All BMC commands are allowed, including configuration commands. -
Page 20: Sessions
Sessions This page displays the information about Active Sessions. Additionally, the trash icon provides the delete function for privileged users. Click Refresh to refresh the Sessions status. LDAP The Lightweight Directory Access Protocol (LDAP) is an application protocol for reading and editing directories over an IP network. -
Page 21: Thermal
Option Description Power Status Current status of the Power Control (OFF or ON). Power On System Turns on the system when it is in the "off" state. Power Off System Turns off the system when it is in the "on" state. Power Cycle System Turns off, then reboots the system (cold boot). -
Page 22: Email Settings (Smtp)
Email Settings (SMTP) The Email Settings page is used to configure the alert. Users can receive an alert by e-mail when events occur. Setting steps: 1. Check the Global Alerting Enable box 2. Press Apply Change 3. Then go to Email Setting page(see Figure 6-9) 4. -
Page 23: Configuration
These virtual devices can read, write (providing the property is not read only) and boot, which are similar with any other CD-ROMs or floppies in the remote system. But only when certain media redirections are active, these virtual devices are available in the remote operating system or BIOS setting menu. The setting is valid after remote system reset or it is power-on or power-off. - Page 24 ThinkServer Remote Management Module User Guide...
-
Page 25: Chapter 7. Languages
Chapter 7. Languages The Web UI’s display will according to the browser’s language to decide which language to use in Web UI. The languages currently offered are: Chinese/English. © Copyright Lenovo 2011... - Page 26 ThinkServer Remote Management Module User Guide...
-
Page 27: Appendix A. Faq
2. Q: Remote Management Module can not be connected. A: check the hardware (1). Whether the host on which the Remote Management Module residents is connected to power supply or not? (2). Check your network configuration (IP address, router, etc.). © Copyright Lenovo 2011... - Page 28 ThinkServer Remote Management Module User Guide...
-
Page 29: Appendix B. Notices
Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead. -
Page 30: Trademarks
Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo The Lenovo logo ThinkServer Internet Explorer and Windows are trademarks of the Microsoft group of companies. Other company, product, or service names may be trademarks or service marks of others.