Page 1 pÅêÉÉåmolJff=`çåíêçääÉê rëÉêÛë=dìáÇÉ • Manual # 26-0505000-00 • Revision A...
Page 2 30 days after the transfer of risks. In the event of justified notice of compliant, Barco can repair the fault or provide a replacement at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a reduction in the purchase price or cancellation of the contract.
Page 3 Not included in the guarantee coverage are system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance are not subject to the guarantee provided by Barco either.
Page 4 To avoid fire hazard, use only the fuse having identical type, voltage rating, and current rating characteristics. Refer fuse replacement to qualified service personnel. aç=kçí=léÉê~íÉ=áå=bñéäçëáîÉ=^íãçëéÜÉêÉë To avoid explosion, do not operate this product in an explosive atmosphere. ScreenPRO-II Controller • User’s Guide...
Page 5 Ein Ausrufungszeichen innerhalb eines gleichwinkeligen Dreiecks dient dazu, den Benutzer auf wichtige Bedienungs-und Wartungsanweisungen in der Dem Great beiliegenden Literatur aufmerksam zu machen. ScreenPRO-II Controller • User’s Guide...
Page 6 `Ü~åÖÉ=eáëíçêó The table below lists the changes to the ScreenPRO-II Controller User’s Guide. Table 0-1. Change History Date ECO # Description Approved By 8/3/06 1666 ScreenPRO-II Controller User’s Guide R. Pellicano ScreenPRO-II Controller • User’s Guide...
Page 7: Table Of Contents
System Overview ..........20 ScreenPRO-II Controller ........20 A Word About Layers.
Page 8 System Installation ..........73 ScreenPRO-II Genlock Termination ......76 BlendPRO-II Widescreen Lock Connections .
Page 9 Luma Key Functions ......157 Color Key Functions ......157 ScreenPRO-II Controller • User’s Guide...
Page 10 Input Setup ..........206 ScreenPRO-II Controller • User’s Guide...
Page 11 Programming Moves ........238 Program a Move on Preview ......238 ScreenPRO-II Controller • User’s Guide...
Page 12 In This Appendix..........255 ScreenPRO-II Input Specifications ....... . 256 ScreenPRO-II Output Specifications .
Page 13 Ethernet Upgrade Method ........274 Troubleshooting Ethernet Communication ....275 fåÇÉñ =K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=KOTT ScreenPRO-II Controller • User’s Guide...
Page 14 Table of Contents ScreenPRO-II Controller • User’s Guide...
Page 15: Chapter Structure
NK==fåíêçÇìÅíáçå This chapter is designed to introduce you to the ScreenPRO-II Controller User’s Guide. Areas to be covered are: • Chapter Structure • How to Use This Guide • Conventions • Terms and Definitions • System Overview • Application Questions...
Page 16 NK==fåíêçÇìÅíáçå Chapter Structure `Ü~éíÉê=píêìÅíìêÉ The following chapters provide instructions for all aspects of ScreenPRO-II Controller operations: • Chapter 1, “Introduction” provides a system overview, a list of features, and discusses easy ways to use this guide. • Chapter 2, “Hardware Orientation”...
Page 17 For operating instructions, refer to Chapter 6, “Operations” on page 215. Should you have any questions regarding the installation or operation of the MatrixPRO ScreenPRO-II Controller, please consult with the factory. Refer to Appendix C, “Upgrading Software” on page 269 for contact information.
Page 18: Conventions
When two buttons together are required for an operation or function, the plus (+) sign is used between the buttons. This procedure requires that you hold down the first button, then press the second. Example: Press Learn + 2 to store the ScreenPRO-II Controller setup in preset register 2. •...
Page 19: Terms And Definitions
• A “LOGO” is a full screen image that is selected from one of three still frames that you can capture with each individual ScreenPRO-II unit. A maximum of 12 still frames can therefore be controlled from the ScreenPRO-II Controller.
Page 20: System Overview
• Effect Combinations pÅêÉÉåmolJff=`çåíêçääÉê The ScreenPRO-II Controller is a versatile interface that enables users to control up to four individual ScreenPRO-II units and peripheral equipment (such as BlendPRO-II, MatrixPRO routers and ImagePRO). The ScreenPRO-II Controller offers the complete functionality of the ScreenPRO-II front panel, plus many features that are not available on the local panel.
Page 21 A layer is defined as an image display element (such as a background, PIP, or Key) with an associated visual priority. The ScreenPRO-II mixer itself has two layers, A and B. For complete flexibility, each layer can be assigned to either PIP or Key functionality.
Page 22: Dual Destination System
PIPs or Keys. póëíÉã=`çãÄáå~íáçåë The ScreenPRO-II Controller can be configured in a variety of different ways, using both single screen and widescreen destinations. You can use up to four ScreenPRO-II units and up to four Aux destinations. The only limitation is one widescreen destination per ScreenPRO-II Controller, comprised of up to four ScreenPRO-II units and a BlendPRO-II.
Page 23 The figure below illustrates a dual-destination system comprised of the ScreenPRO-II Controller, two individual ScreenPRO-II units and two single-screen projectors (destinations). Within this system, Ethernet is used for communications between components, and all ScreenPRO-II inputs are received via routers or direct connections. Destination Destination...
Page 24 NK==fåíêçÇìÅíáçå System Overview =nì~ÇêìéäÉ=aÉëíáå~íáçå=póëíÉã The figure below illustrates a quadruple-destination system comprised of the ScreenPRO-II Controller, four individual ScreenPRO-II units and four single-screen projectors. Destination Destination Destination Destination Inputs (from routers and direct sources) ScreenPRO-II Controller ScreenPRO-II Ethernet Hub / Switch Figure 1-4.
Page 25 ScreenPRO-II BlendPRO-II Ethernet Hub / Switch Figure 1-5. ScreenPRO-II Controller system with one widescreen destination The BlendPRO-II accepts up to four inputs, thus, widescreen systems can be configured with dual (as shown above), triple or quadruple screen blends. Important For all Widescreen configurations using BlendPRO-II, ensure that you review the “...
Page 26 NK==fåíêçÇìÅíáçå System Overview aì~ä=aÉëíáå~íáçåI=aì~ä=^ìñ=póëíÉã The figure below illustrates a system that includes two individual ScreenPRO-II units, two single-screen projectors and two “Aux” destinations: • The “standard” Aux destination is a single monitor that takes its input from one router output (in a single format).
Page 27 PIP or a key that can transition. For example, PIP A B indicates that you can dissolve between sources within the PIP. Similar to individual ScreenPRO-II units, the ScreenPRO-II Controller enables you to control two backgrounds, two scalable layers in the mixer plus an unscaled DSK and a full screen, unscaled LOGO.
Page 28 In this effect, because the DSK is in use, the background cannot transition — you can only use background A. Here, you can independently fade two scaled PIPs up and down — with or without the DSK on screen. Background A Figure 1-11. Effect 5 Diagram ScreenPRO-II Controller • User’s Guide...
Page 29 This transition is similar to effect 5, but because the DSK is not in use, the background can transition. You can also independently fade the two PIPs. ↔ Background A Figure 1-12. Effect 6 Diagram ScreenPRO-II Controller • User’s Guide...
Page 30: Application Questions
Application Questions ^ééäáÅ~íáçå=nìÉëíáçåë At Barco, we take pride in offering unique solutions to demanding technical problems. If you have application questions, require further information or would like to discuss your application requirements in more detail, please call (916) 859-2500. Our Customer Support Engineers will be happy to provide you with the support you need.
Page 31: In This Chapter
OK==e~êÇï~êÉ=lêáÉåí~íáçå få=qÜáë=`Ü~éíÉê This chapter provides detailed information about the ScreenPRO-II Controller’s hardware. The following topics are discussed: • ScreenPRO-II Controller Rear Panel • ScreenPRO-II Controller Front Panel • Use of Color • Front Panel Sections Note For complete details on BlendPRO-II’s hardware, refer to the “...
Page 32 2. Hardware Orientation ScreenPRO-II Controller Rear Panel pÅêÉÉåmolJff=`çåíêçääÉê=oÉ~ê=m~åÉä The figure below illustrates the ScreenPRO-II Controller rear panel: MEMORY CARD T250V 2A FUSE EXT COMM KEYBOARD TALLY CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY ETHERNET CONSOLE WITH SAME TYPE AND RATING OF FUSE Figure 2-1.
Page 33 Console Port One 9-pin D connector is provided for RS-232 “command line” communications with the ScreenPRO-II Controller, and for downloading code in the field. The port is configured as follows: DCE, 115K baud, 8 data bits, 1 stop bit, no parity bits The serial port can be connected to a standard PC serial port with a straight through DB-9 to DB-9 cable.
Page 34: Touch Screen Menu Section
2. Hardware Orientation ScreenPRO-II Controller Front Panel pÅêÉÉåmolJff=`çåíêçääÉê=cêçåí=m~åÉä The figure below illustrates the ScreenPRO-II Controller front panel: Adjustment Panel ScreenPRO II Controller Source Crop Bottom INPUT OUTPUT SYSTEM EFFECTS Left Right FRAME REMOTE Fine STATUS DISPLAY GRAB CONTROL Reset Adjust...
Page 35 46 for details. Layer Control Section The Layer Control Section is the operational heart of the ScreenPRO-II Controller, enabling you to assign sources to PIPs and keys. Here, you control the overall “look” on Preview and Program. Refer to the “...
Page 36 2. Hardware Orientation Use of Color rëÉ=çÑ=`çäçê Color plays an important “visual” role with the ScreenPRO-II Controller’s front panel buttons: White buttons are used for sources. Yellow buttons are functions and modes that apply to the active (blinking) layer. Functions include assigning PIPs and keys to the active layer, setting up moves, freezing the active layer and swapping layer priority.
Page 37 This section provides detailed descriptions and illustrations of each front panel section. The following topics are discussed: • Touch Screen Menu Section • Presets Section • Destination/Aux Bus • Joystick Section • Source Selection Bus • Layer Functions Section • Layer Control Section • Transition Section ScreenPRO-II Controller • User’s Guide...
Page 38 ADJ rotary knob to adjust the value. Important When adjusting parameters, there is no Enter button. If you adjust a value with the knobs or the softkeys, that function, parameter or value is immediately active in Preview. ScreenPRO-II Controller • User’s Guide...
Page 39 To store a Controller setup in Preset register 2, press Learn + 2 . Delete — hold down Delete , then press the desired Preset button to delete that register from memory. Delete To delete Preset 5 from memory, press Delete + 5 . ScreenPRO-II Controller • User’s Guide...
Page 40 (or router) output. The transitions that you perform will affect the selected destinations only, leaving the unselected destinations as they were. The ScreenPRO-II Controller provides eight destinations — four standard (e.g., projectors) and four Aux (auxiliary).
Page 41 DEST/AUX — press to switch the bus between standard (projector) destinations and Aux (auxiliary) destinations, such as monitors. DEST • When DEST/AUX is off, you are selecting standard (projector) destinations. • When DEST/AUX is lit, you are selecting Aux (auxiliary) destinations. ScreenPRO-II Controller • User’s Guide...
Page 42 PIP (or Key) size. Note The Z-Axis Control can also be used to increase or decrease the value of a highlighted parameter, such as a matte color, key clip and gain, border size and much more. ScreenPRO-II Controller • User’s Guide...
Page 43 Joystick’s adjustment range. Fine Adjust In Chapter 6, refer to the “ Modifying Layers On Program ” section on page 234 for additional details on Joystick usage. ScreenPRO-II Controller • User’s Guide...
Page 44 ScreenPRO-II or a router input. Please note: • If you have configured a ScreenPRO-II to use internal routing (on the Destination Setup Menu ), both the white buttons (analog sources) and the yellow buttons (HD-SDI/SD-SDI sources) are active. You can assign a maximum of 16 analog and 2 HD-SDI/SD-SDI sources.
Page 45 Shift — the Shift button is a toggle: press once to light, press again to turn off. When lit, press the desired source button to access the second row of numbered sources ( 9 - 16 ). Shift ScreenPRO-II Controller • User’s Guide...
Page 46 If the PIP on Layer B is visually on top of the PIP on Layer A , press Z-order Swap Z-Order to place Layer A’s PIP on top. In Chapter 6, refer to the “ Using Swap Z-Order ” section on page 236 for instructions. ScreenPRO-II Controller • User’s Guide...
Page 47 ” section on page 228 for details. Freeze — enables you to freeze a layer on both Program and Preview. In Chapter 6, refer to the “ Using Freeze ” section on page 236 for instructions. Freeze ScreenPRO-II Controller • User’s Guide...
Page 48 • Two background sources, two layers (in the mixer), one DSK and one full screen LOGO are provided — identical to the layers on an individual ScreenPRO-II. • The buttons are arranged left-to-right in order of visual priority — from the backgrounds (at the lowest priority) to the LOGO (at the highest visual priority).
Page 49 • The LOGO is the system’s highest priority layer. The LOGO “source” is selected from one of the individual ScreenPRO-II’s three internal frame stores. • The LOGO layer is often used as a “black preview” function. If Black is selected as the “type”...
Page 50 MIX — press to select a mix (dissolve) as the current transition type for the selected destination. The button lights when enabled, and the mix is initiated by pressing AUTO TRANS . Auto transition rates are defined using the Effects Menu . ScreenPRO-II Controller • User’s Guide...
Page 51 In Chapter 4, refer to the “ Effects Menu ” section on page 146 for menu details. • In Chapter 6, refer to the “ Working with Transitions ” section on page 241 for operational procedures. ScreenPRO-II Controller • User’s Guide...
Page 52 2. Hardware Orientation Front Panel Sections ScreenPRO-II Controller • User’s Guide...
Page 53: Safety Precautions
PK==e~êÇï~êÉ=fåëí~ää~íáçå få=qÜáë=`Ü~éíÉê This chapter provides comprehensive installation instructions for the ScreenPRO-II Controller system’s hardware. The following topics are discussed: • Safety Precautions • Unpacking and Inspection • Site Preparation • Controller Installation • Cable, Adapter and Accessory Information • Connection Charts •...
Page 54 Before opening the ScreenPRO-II Controller shipping box, inspect it for damage. If you find any damage, notify the shipping carrier immediately for all claims adjustments. As you open the box, compare its contents against the packing slip. If you find any shortages, contact your sales representative.
Page 55 AC Power, 7 foot, 10A 1 Cord Supplied Note In Chapter 3, “ Hardware Installation ” of the ScreenPRO-II User’s Guide , refer to the “ Cable and Adapter Information ” section for details on the components supplied with individual ScreenPRO-II units.
Page 56: Connection Charts
Destination Setup Menu . Note that the use of routers offers less restrictions with regard to assigning sources to layers. If you have configured a ScreenPRO-II to use internal routing , both the white buttons (analog sources) and the yellow buttons (HD-SDI/SD-SDI sources) are active on the Source Selection Bus .
Page 57 If you are using internal routing, complete the analog input chart for direct or DA analog connections to each ScreenPRO-II and other target analog destinations. Be sure to check ( ) whether or not the analog input is a direct connection, or from a DA output.
Page 58: External Routing - Sample Analog Router I/O Chart
3. Hardware Installation Connection Charts p~ãéäÉ=`çååÉÅíáçå=`Ü~êíë=Ô=bñíÉêå~ä=oçìíáåÖ Following are sample connection charts for a ScreenPRO-II Controller system configured for external routing . The system is comprised of the following components: • 2 x ScreenPRO-II • 1 x widescreen destination (using two projectors) •...
Page 59 Demo A ImagePRO, Analog Input Demo B Betacam bñíÉêå~ä=oçìíáåÖ=Ô=p~ãéäÉ=aáÖáí~ä=oçìíÉê=fLl=`Ü~êí With a ScreenPRO-II configured to use external routing, use the following chart to map SDI Router input and output connections: Table 3-3. Sample Digital Router I/O Chart Router #2 — SDI Router ←...
Page 60 Connection Charts táÇÉëÅêÉÉå==Ô=p~ãéäÉ=asf=`çååÉÅíáçå=`Ü~êí Each ScreenPRO-II has two DVI inputs for the Background and DSK ( BG/DSK in A and BG/DSK in B ). Widescreen backgrounds will typically originate from a multi-head graphics card, while single screen backgrounds are typically distributed from one computer through a DA or signal splitter.
Page 61 3. Hardware Installation Connection Charts táÇÉëÅêÉÉå=Ô=p~ãéäÉ=^ìñáäá~êó=aÉëíáå~íáçå=`Ü~êí The ScreenPRO-II Controller enables you to configure up to four auxiliary destinations. Use the following chart to map the distribution of each auxiliary destination: Table 3-6. Sample Aux Destination Connection Chart Aux Destinations Dest...
Page 62: Internal Routing - Sample Analog Input Chart
3. Hardware Installation Connection Charts p~ãéäÉ=`çååÉÅíáçå=`Ü~êíë=Ô=fåíÉêå~ä=oçìíáåÖ Following are sample connection charts for a ScreenPRO-II Controller system configured for internal routing . The system is comprised of the following components: • 2 x ScreenPRO-II • 2 x single screen destinations •...
Page 63 Connection Charts fåíÉêå~ä=oçìíáåÖ=Ô=p~ãéäÉ=^å~äçÖ=fåéìí=`Ü~êí With a ScreenPRO-II configured to use internal routing (on the Destination Setup Menu ), use the following chart to map Analog Inputs to each ScreenPRO-II and other target analog destinations. Note that the use of DAs is recommended to provide identical inputs to each ScreenPRO-II (or target device).
Page 64 Connection Charts páåÖäÉ=pÅêÉÉåë=Ô=p~ãéäÉ=asf=`çååÉÅíáçå=`Ü~êí Each ScreenPRO-II has two DVI inputs for the Background and DSK ( BG/DSK in A and BG/DSK in B ). Single screen backgrounds are typically distributed from one computer through a DA or signal splitter. Use the following chart to map your Background and DSK DVI connections: Table 3-9.
Page 65 3. Hardware Installation Connection Charts páåÖäÉ=pÅêÉÉåë=Ô=p~ãéäÉ=^ìñáäá~êó=aÉëíáå~íáçå=`Ü~êí The ScreenPRO-II Controller enables you to configure up to four auxiliary destinations. Use the following chart to map the distribution of each auxiliary destination: Table 3-11. Sample Aux Destination Connection Chart Aux Destinations Dest...
Page 66: Blank Connection Charts
Analog Router I/O Chart ” section on page 59 for a sample chart. Table 3-12. Analog Router I/O Chart Router #1 — Analog Router ← → Source Name Controller Input # Input | Output Connects to: ScreenPRO-II Controller • User’s Guide...
Page 67 Digital Router I/O Chart ” section on page 59 for a sample chart. Table 3-13. Digital Router I/O Chart Router #2 — Digital Router ← → Source Name Controller Input # Input | Output Connects to: ScreenPRO-II Controller • User’s Guide...
Page 68 Internal Routing — Sample Analog Input Chart ” section on page 63 for a sample chart. Table 3-14. Analog Input Chart — Direct or DA Connections Analog Inputs Source Name Direct DA Output Target Input ScreenPRO-II Controller • User’s Guide...
Page 69 Internal Routing — Sample Digital Input Chart ” section on page 63 for a sample chart Table 3-15. Digital Input Chart — Direct or DA Connections Digital Inputs Source Name Direct DA Output ScreenPRO-II Input ScreenPRO-II Controller • User’s Guide...
Page 70 Connection Charts asf=`çååÉÅíáçå=`Ü~êí Each ScreenPRO-II has two DVI inputs for the Background and DSK ( BG/DSK in A and BG/DSK in B ). Widescreen backgrounds will typically originate from a multi-head graphics card, while single screen backgrounds are typically distributed from one computer through a DA or signal splitter.
Page 71 Connection Charts pí~åÇ~êÇ=aÉëíáå~íáçå=`Ü~êí The ScreenPRO-II Controller enables you to configure up to four standard destinations. Use the following chart to map the distribution of each destination, the usage of BlendPRO-II if required, and the routing of your additional program and preview outputs.
Page 72 3. Hardware Installation Connection Charts ^ìñáäá~êó=aÉëíáå~íáçå=`Ü~êí The ScreenPRO-II Controller enables you to configure up to four auxiliary destinations. Use the following chart to map the distribution of each auxiliary destination: Table 3-18. Aux Destination Connection Chart Aux Destinations Dest Device...
Page 73: System Installation
3. Hardware Installation System Installation póëíÉã=fåëí~ää~íáçå This section provides instructions for installing your ScreenPRO-II Controller system. If required, use the two previous sample system diagrams for reference: • Refer to “ Figure 3-1 ” on page 58 for an illustration of a Sample System with External Routing .
Page 74 Ethernet Hub or Switch. Connect all routers (such as MatrixPRO) to the Ethernet Hub or Switch. Serial Connections — the ScreenPRO-II Controller’s serial port is configured as DCE, 115K baud, 8 data bits, 1 stop bit, no parity bits.
Page 75: Screenpro-Ii Genlock Termination
ScreenPRO-II’s Genlock In connector (or to other video devices in the chain). If a particular ScreenPRO-II is the last device in a reference video chain, do not make any connections to the Genlock Loop connector. Refer to the “...
Page 76 Un-terminated — when the switch is out, the connection is un-terminated. If a particular ScreenPRO-II chassis is the last device in a reference video chain, ensure that the Termination Switch is pushed in. If a particular ScreenPRO-II chassis is in the middle of a reference chain, ensure that the Termination Switch is out.
Page 77: Blendpro-Ii Widescreen Lock Connections
ScreenPRO-II Controller system that uses BlendPRO-II. Use this figure for reference during the signal installation process. If required, refer to the “ BlendPRO-II User’s Guide ” and the “ ScreenPRO-II User’s Guide ” for details on specific rear panel connectors. GENLOCK...
Page 78 3. Hardware Installation BlendPRO-II Widescreen Lock Connections Connect the first ScreenPRO-II’s GENLOCK LOOP connector to the GENLOCK IN connector on the ScreenPRO-II unit with the next highest numbered ID . (If your system includes three ScreenPRO-IIs) — Connect the second ScreenPRO-II’s GENLOCK LOOP connector to the GENLOCK IN...
Page 79: Overview Of Edge-Blending Technology
• Use of a Single High Definition Image High Definition source material has a resolution of 1920 pixels x 1080 lines. Images of this type can be reformatted to drive multiple screens. The reformatting ScreenPRO-II Controller • User’s Guide...
Page 80 The inherent resolution of the output image is limited only by the processing power of the multi-head graphics board. Image resolutions with up to 10,000 pixels of horizontal resolution can be achieved with current technology. ScreenPRO-II Controller • User’s Guide...
Page 81 1280 1280 Original Image from _äÉåÇmolJff Multi-head Graphics Card 1024 Unused Source Image for Material _äÉåÇmo Projector 1 Image for ÇmolJff Projector 2 Image Overlap Region _äÉåÇmolJff Figure 3-6. Image Overlap and Data Doubling ScreenPRO-II Controller • User’s Guide...
Page 82 Custom test patterns and an alignment procedure are used to simplify this process and provide an optimal result. • Mixing and matching projectors is not recommended as it makes the adjustment process much more difficult. ScreenPRO-II Controller • User’s Guide...
Page 83 Projector 2 Image Projector 1 Image _äÉåÇmolJff Unused Image Unused Source Overlap Source Material Region Material Figure 3-9. Center Justification This completes the hardware installation chapter. Please continue with Chapter 4, “ Menu Orientation .” ScreenPRO-II Controller • User’s Guide...
Page 84: Hardware Installation
3. Hardware Installation Overview of Edge-Blending Technology ScreenPRO-II Controller • User’s Guide...
Page 85 QK==jÉåì=lêáÉåí~íáçå få=qÜáë=`Ü~éíÉê This chapter describes all ScreenPRO-II Controller menus, including how they are accessed, the functions that are available, and descriptions of each menu tree (in block diagram format). Note In this chapter, softkey labels on the menus are shown in bold upper and lowercase letters between brackets.
Page 86: In This Chapter
“All” Adjustments — For widescreen destinations, if a parameter is adjusted on a menu displaying an “ All ” ID condition, all values for all ScreenPRO-II’s in the destination will snap to the new value. To adjust an individual ScreenPRO-II’s values within the widescreen configuration, highlight the ID line, use the ADJ knob to select a specific destination, and then adjust a parameter in the normal manner.
Page 87: Home Menu
146 for details. • Press STATUS to access the Status Menu . Refer to the “ Status Menu ” section on page 147 for details. • Press SAVE to save the system configuration in non-volatile memory. ScreenPRO-II Controller • User’s Guide...
Page 88: Input Menu Tree
Sync Slice V Position FORCE RESET ALL Sharpness ACQUIRE SAVE SAVE HOME FORCE ACQUIRE SAVE APPLY FORMAT FORCE ACQUIRE Figure 4-2. Input Menu Tree All functions and sub menus are discussed in the following sections. ScreenPRO-II Controller • User’s Guide...
Page 89 Figure 4-3. Input Menu (sample) The Input Menu is used to adjust all parameters relating to dedicated and routed inputs, including the physical sources connected to individual ScreenPRO-II units. The menu enables you to set all configuration options for the selected input.
Page 90: Input Menu Functions
ID in the destination. When a parameter is adjusted, all values for all ScreenPRO-II’s in the destination will snap to the new value. If an individual ID is shown (e.g., 2 ), it represents that ScreenPRO-II alone, and adjustments will only affect that unit. •...
Page 91 4. Menu Orientation Input Menu • Input Type — sets the type of input connected to the ScreenPRO-II. Available choices change depending on the selected Format , and the choice affects the Color Space selection. Input types include: Composite/S-Vid HD SDI •...
Page 92: Input Configuration Menu
Press APPLY FORMAT to apply a manually selected input format. In Appendix A, refer to the “ ScreenPRO-II Input and Output Resolutions “section on page 263 for details on all available resolutions. • Press { SIZING } to display the Sizing Menu . Refer to the “...
Page 93 If multiple destinations are selected (for example, when you Note are using two single-screen configurations), pressing SAVE copies input parameters to both destinations, eliminating the need to configure and save each input twice. ScreenPRO-II Controller • User’s Guide...
Page 94 Mode — select 16:9 , 5:4 , 4:3 , 3:2 , 1:1 or Custom aspect ratios. • Ratio — when Custom is selected, use the knob to enter a custom aspect ratio. The field is hidden when pre-defined ratios are selected. ScreenPRO-II Controller • User’s Guide...
Page 95 ScreenPRO-II’s in the destination will snap to the new value. If an individual ID is shown (e.g., 2 ), it represents that ScreenPRO-II alone, and adjustments will only affect that unit. ScreenPRO-II Controller • User’s Guide...
Page 96 SAVE to save the selected input in the designated input file. • Press { FORCE ACQUIRE } to force the ScreenPRO-II Controller to perform the optimum image setup. Note If you switch to another input and there is no valid input video, the settings are not applicable and N/A is displayed.
Page 97 ID in the destination. When a parameter is adjusted, all values for all ScreenPRO-II’s in the destination will snap to the new value. If an individual ID is shown (e.g., 2 ), it represents that ScreenPRO-II alone, and adjustments will only affect that unit. •...
Page 98 Red Brightness < % > Grn Contrast < % > Grn Brightness < % > Blue Contrast < % > Blue Brightness < % > RESET Figure 4-9. Color Balance Menu (sample — for RGB sources) ScreenPRO-II Controller • User’s Guide...
Page 99 ID in the destination. When a parameter is adjusted, all values for all ScreenPRO-II’s in the destination will snap to the new value. If an individual ID is shown (e.g., 2 ), it represents that ScreenPRO-II alone, and adjustments will only affect that unit. •...
Page 100: Output Menu
Background Frmt Raster Box Size Alignment Pattern Marker Mode Overlap Width Alignment Pattern Data Doubling Justification Feather Mode Feather Gamma Figure 4-10. Output Menu Tree All functions and sub menus are discussed in the following sections. ScreenPRO-II Controller • User’s Guide...
Page 101 WIDE SETTINGS FORMAT PATTERN SCREEN Figure 4-11. Output Menu (sample) The Output Menu enables you to configure ScreenPRO-II outputs, wide screen parameters and test patterns. To access the menu: • Select a destination on the Destination Bus . • Press OUTPUT on the Home Menu .
Page 102: Output Menu Functions
(in a wide screen application). In this situation, all changes to the Output Menu affect all ScreenPRO-II units in the wide screen definition. • Format — sets the resolution and frame rate at which you want to drive the destination’s projector(s).
Page 103 If you elect to use external Genlock for single or widescreen configurations, PAL or NTSC black burst or composite sync signals are recommended. • In widescreen mode, you can optionally connect external Genlock to BlendPRO- II’s Genlock In connector — but not to the individual ScreenPRO-II units. ScreenPRO-II Controller • User’s Guide...
Page 104 All — adjustments affect all program and preview monitors/projectors. Preview — adjustments affect preview monitors only. SPII Program — adjustments affect only the monitors/projectors connected to ScreenPRO-II program outputs. BPII Program — adjustments affect only the monitors/projectors connected to BlendPRO-II program outputs.
Page 105 All — adjustments affect all program and preview monitors/projectors. Preview — adjustments affect preview monitors only. SPII Program — adjustments affect only the monitors/projectors connected to ScreenPRO-II program outputs. With this selection, test patterns will be data-doubled and edge-feathered. BPII Program — adjustments affect only the monitors/projectors connected to BlendPRO-II program outputs.
Page 106: Wide Screen Settings Menu
The following functions are provided on the Wide Screen Settings Menu . • Total Projectors — indicates the total number of ScreenPRO-II systems that have been assigned to the wide screen destination. This field is for information only, as derived from the Destination Setup Menu .
Page 107 Justification — sets the desired wide screen justification, either Center or Left . Once set, wide screen markers adjust accordingly. In the Feathering section: • Mode — enables or disables edge feathering. • Gamma — sets gamma for the feathered regions. Adjustment range: 1.0 to 5.0 . ScreenPRO-II Controller • User’s Guide...
Page 108: System Menu
Parity SP Input Map To NEXT TEST IP QUAD COMM Stop Bits PATCH MAC Addr DELETE PATCH TEST COMM Figure 4-16. System Menu Tree All functions and sub menus are discussed in the following sections. ScreenPRO-II Controller • User’s Guide...
Page 109: System Reset Menu
Destination Setup Menu ” section on page 117 for details. • Press NETWORK SETUP to display the Network Setup Menu . Refer to the “ Network Setup Menu ” section on page 124 for details. ScreenPRO-II Controller • User’s Guide...
Page 110: Input Source Patch Menu
The following sub menus can be accessed from the System Menu : • System Reset Menu • Software Version Menu • Diagnostics Setup Menu • Destination Setup Menu • Network Setup Menu • Input Source Patch Menu • Router Specification Menu ScreenPRO-II Controller • User’s Guide...
Page 111 Press RESET to perform the selected reset operation. When the confirmation screen appears: Press to start the reset procedure. An “ In Progress ” message will be displayed. Press NO } to cancel the procedure. ScreenPRO-II Controller • User’s Guide...
Page 112 Controller — displays the Controller’s software version. • BlendPRO-II — displays BlendPRO-II’s software version. • SP — these lines display each ScreenPRO-II’s software version. One line is shown for each active destination. • In the lower portion of the menu, the system actively compares all software versions to that of the Controller: If all software versions match the Controller’s version, the display...
Page 113 Figure 4-20. Diagnostics Setup Menu (sample) The Diagnostics Setup Menu enables you to perform a variety of diagnostic tests on the ScreenPRO-II Controller. The following functions are provided: • Reset Rotary Encoders — (Yes/No) determines whether or not you wish to reset the rotary encoder values when you exit the Rotary Encoder Menu .
Page 114 Figure 4-21. Rotary Encoder Menu (sample) The Rotary Encoder Menu enables you to test the functionality of each rotary encoder, displaying both relative and absolute counts for each. • Press EXIT to return to the Diagnostics Setup Menu . ScreenPRO-II Controller • User’s Guide...
Page 115 The TBAR range is 0 to 100%. • The Joystick range is -100 to 100 on each axis ( X , Y and Z ). • Press EXIT to return to the Diagnostics Setup Menu . ScreenPRO-II Controller • User’s Guide...
Page 116 The Key Detect Menu shows you the key that is pressed, its status (pressed or released) its scan code and its location in the row and column matrix. • Press EXIT to return to the Diagnostics Setup Menu . ScreenPRO-II Controller • User’s Guide...
Page 117 • Type — displays (or sets) the selected destination type. For standard destinations: • Displays [Single Screen SP] if one ScreenPRO-II has been added to the destination’s configuration. • Displays [Widescreen SP] if two, three or four ScreenPRO-IIs have been added to the destination’s configuration.
Page 118 4. Menu Orientation System Menu • SP to Add — (as you rotate the ADJ knob), lists all available ScreenPRO-II units that can be assigned to the selected destination. Units are identified by their ID number. If a ScreenPRO-II is currently assigned to another destination, it will not appear in the list.
Page 119 4. Menu Orientation System Menu pÅêÉÉåmolJff=dÉåäçÅâ=qÉêãáå~íáçå=jÉåì After having configured a wide screen destination, the ScreenPRO-II Genlock Termination Menu will automatically appear if the system senses that any of the termination switches (in the Widescreen Lock signal chain) are improperly set.
Page 120 An Aux destination is the output of a router, which is typically connected directly to a monitor — rather than to the ScreenPRO-II. This type of destination is single format (e.g., an analog monitor can only accept signals from an analog router).
Page 121 Analog Router Name — selects the router from which analog sources will be routed to the ImagePRO or PrePRO-II. Analog Router Output — selects the specific router output designated as Aux (as assigned on the router’s Output Patch Menu ). ScreenPRO-II Controller • User’s Guide...
Page 122 SDI Router Output — selects the specific router output designated as Aux (as assigned on the router’s Output Patch Menu ). ImagePRO Input or PrePRO-II Input — selects the ImagePRO or PrePRO-II input to which the SDI router output is connected. ScreenPRO-II Controller • User’s Guide...
Page 123 Only one Analog and one SDI router can be connected to a PrePRO-II unit. • In order to properly create “source files” on ImagePRO: On the ScreenPRO-II Controller console, select a ScreenPRO-II Controller destination. On the Input Menu , acquire the selected source in the normal manner.
Page 124 Figure 4-28. Network Setup Menu (sample) For reference only, the Network Setup Menu displays the available IP range for the ScreenPRO-II Controller system. The following information is provided: • Network DHCP — this non-selectable field confirms that the Controller is a DHCP...
Page 125 Figure 4-29. Input Source Patch Menu (sample) The Input Source Patch Menu enables you to associate (patch) specific router inputs to specific source buttons on the ScreenPRO-II Controller. The menu also enables you to assign tallies, and select connections to the ScreenPRO-II units.
Page 126 4. Menu Orientation System Menu DAs to similar ScreenPRO-II inputs, and enables all ScreenPRO-IIs to switch simultaneously to the same input. Note Asterisks around the ID number (e.g., *1* ) indicate that the selected ID has not been detected by the system. However, you can proceed with patching, and once the ID is detected, the patch will be completed as programmed.
Page 127 The D/A selections are provided for future implementation. • Number of Inputs — identifies the number of inputs on the selected router. • Number of Outputs — identifies the number of outputs on the selected router. ScreenPRO-II Controller • User’s Guide...
Page 128: Comm Setup Menus
• DVILink 18x18 Router Support The ScreenPRO-II Controller supports the DVILink 18x18 router enabled with serial control. Connect the router to the EXT COMM port on the back of the Controller. In Appendix A, refer to the “...
Page 129 If the test is successful, a “ ROUTER CONNECTED ” message will appear that includes the Router name and version. If the test is unsuccessful, a “ ROUTER FAILED ” message will appear. In this condition, re-check all connections and settings, and repeat the test. ScreenPRO-II Controller • User’s Guide...
Page 130 If the test is successful, a “ ROUTER CONNECTED ” message will appear that includes the Router name and version. If the test is unsuccessful, a “ ROUTER FAILED ” message will appear. In this condition, re-check all connections and settings, and repeat the test. ScreenPRO-II Controller • User’s Guide...
Page 131 Figure 4-33. Lantronix Setup Menu (sample) The Lantronix Setup Menu enables you to set parameters for multiple Lantronix Ethernet- to-Serial device servers. The ScreenPRO-II Controller supports Lantronix models UDS100 and UDS200 . The menu will appear blank until the Lantronix device is “discovered.”...
Page 132 When a router is chosen on the Router Specification Menu , you then use the Output Patch Menu to associate a specific output with a ScreenPRO-II ID and input. This process creates a unique “ Output Patch Table ” for each defined router .
Page 133: Miscellaneous Menu
Black Invalid Vid Device Contrast Controller Options SP to Restore RESET BACKUP LCD CAL LCD Calibration CHECK CARD RESTORE Figure 4-35. Miscellaneous Menu Tree All functions and sub menus are discussed in the following sections. ScreenPRO-II Controller • User’s Guide...
Page 134 4. Menu Orientation Miscellaneous Menu jáëÅÉää~åÉçìë=jÉåì=aÉëÅêáéíáçå The Miscellaneous Menu accesses ScreenPRO-II Controller functions that do not fall into other distinct menu categories. MISCELLANEOUS MENU LIGHT USER BACKUP ADJUST SETTINGS PREF RESTORE Figure 4-36. Miscellaneous Menu To access the menu: •...
Page 135: Console Port Setup Menu
NONE Stop Bits Figure 4-37. Console Port Setup Menu (sample) This menu enables you to verify (or change) ScreenPRO-II Controller’s serial port communication settings (for the Ext Comm port). The following functions are provided: • Baud Rate — sets the port’s baud rate. Range: 2400 to 115200 .
Page 136: Lockout Code Menu
CHANGE LOCKOUT CODE Enter new code: __ __ __ __ Confirm new code: __ __ __ __ Enter and confirm new code using source keys 1 – 8. CANCEL Figure 4-39. Change Lockout Code Menu (sample) ScreenPRO-II Controller • User’s Guide...
Page 137: Edid Dvi Input Format Menu
Figure 4-40. EDID DVI Input Format Menu (sample) The EDID DVI Input Format Menu enables you to update the system’s preferred EDID resolution for each ScreenPRO-II’s two DVI inputs ( Background and DSK ) — for the selected destination bus.
Page 138: Keypad Backlight Menu
• A ScreenPRO-II’s EDID prom is not reset to any default during a factory reset. To change the EDID, you must use the EDID DVI Input Format Menu . hÉóé~Ç=_~ÅâäáÖÜí=jÉåì...
Page 139: Lcd Settings Menu
Once pressed, you will be prompted to touch the center of a target three times. At the conclusion of the procedure, the display is calibrated and the system returns to the Home Menu . ScreenPRO-II Controller • User’s Guide...
Page 140: User Preference Menu
The DSK will be turned off when source video becomes invalid. OFF — shows the full scaler loading procedure, which can temporarily include non-sync and non-stable video. In Chapter 6, refer to the “ Setting User Preferences ” section on page 221 for instructions. ScreenPRO-II Controller • User’s Guide...
Page 141: Backup/Restore Menu
• SP to Restore — Selects the device(s) that you wish to restore. Choose between All devices, or the ID of a specific ScreenPRO-II (e.g., 1 , 2 , 3 ). • Press { BACKUP } to perform a backup operation to the Flash Memory Card using the selected device(s) and options.
Page 142: Frame Grab Menu
FG to Capture Name Menu HOME Saved Location ERASE Confirmation Current Name New Name CAPTURE SAVE Confirmation DELETE RECALL Figure 4-45. Frame Grab Menu Tree All functions and menus are discussed in the following sections. ScreenPRO-II Controller • User’s Guide...
Page 143 The Frame Grab Menu enables you to capture still frames into each ScreenPRO-II system’s three internal frame stores. The “sources” of the still frames are each ScreenPRO-II’s BG A and BG B inputs, or the scaled inputs ( Layer A or B ). Please note: •...
Page 144 The following Frame Grab Menu functions are provided: • Destination — displays the currently selected destination. • ID — displays the ID(s) of the selected destination’s associated ScreenPRO-II system(s). • Frame Number — enables you to select FG_1 , FG_2 or FG_3 for capture, storage, erasure, recall or deletion.
Page 145: Frame Grab Name Menu
“attached” to the file that already resides in permanent (flash) memory. The name will now be shown on all menus in which a still frame can be selected (e.g., LOGO Menu , DSK Input Setup Menu , Background Input Setup Menu , etc.). ScreenPRO-II Controller • User’s Guide...
Page 146: Effects Menu
Curtain Close , Box In and Box Out . Note Wide screen destinations only support Mix transitions. Key frame effects are ignored by ScreenPRO-II destinations. • Transition Edge Width — When WIPE is selected, this field enables you to set the transition’s edge type.
Page 147: Status Menu
• Press STATUS on the Home Menu . The following status information is provided: • ScreenPRO-II Controller — (top line) displays the Controller’s software version. • SCREENPRO-II — lists the number of ScreenPRO-II units detected. • PREPRO-II — lists the number of PresentationPRO-II units detected.
Page 148: Pip Adjustment Menu
Color: Blue Transparency Invert Size Specified Track Size Size Strobe Mode Strobe Interval BORDR SHDOW BORDR SHDOW RESET Figure 4-50. PIP Adjustment Menu Tree All functions and sub menus are discussed in the following sections. ScreenPRO-II Controller • User’s Guide...
Page 149 ADJ knob. • Move Rate — adjusts the rate (in 0.1 second increments) for programmed PIP movement from key frame to key frame. To adjust, use the ADJ knob or twist the Joystick Z-Axis knob. ScreenPRO-II Controller • User’s Guide...
Page 150: Border Menu
Key Frame Effect — indicates the “motion type” that is used to move the PIP from point to point. Note Only the Linear motion type is supported. All other key frame effects are ignored by ScreenPRO-II destinations. • Press BORDR to display the Border Menu .
Page 151 Shadow Menu . Refer to the “ Shadow Menu ” section on page 152 for details. • Press to display the Image Effects Menu . Refer to the “ Image Effects Menu ” section on page 153 for details. ScreenPRO-II Controller • User’s Guide...
Page 152 Border Menu . Refer to the “ Border Menu ” section on page 151 for details. • Press to display the Image Effects Menu . Refer to the “ Image Effects Menu ” section on page 153 for details. ScreenPRO-II Controller • User’s Guide...
Page 153 For a sepia tone effect, turn Monochrome Mode on, and set Red to 100, Green to 65 and Blue to 10. • Invert — inverts all image colors. • Hue — adjusts the image’s hue, by rotating color vectors throughout the 360 degree color spectrum. ScreenPRO-II Controller • User’s Guide...
Page 154 Note To remove any image effects from the PIP or Key, press the RESET button in the Layer Functions Section — while the Image Effects Menu is active. No other PIP parameters will be affected. ScreenPRO-II Controller • User’s Guide...
Page 155: Key Menu
Strobe Mode STATS Strobe Interval HOME STATS MATTE STATS SIZE & RESET PICK COLOR MATTE GRAB COLOR SIZE & Figure 4-55. Key Menu Tree All functions and sub menus are discussed in the following sections. ScreenPRO-II Controller • User’s Guide...
Page 156: Luma Key Functions
Choose between Luma , Color , or Cut + Fill when Split Mode is enabled ( Split button is on). Refer to the following sections for details. • Luma Key Functions • Color Key Functions • Cut + Fill Key Functions ScreenPRO-II Controller • User’s Guide...
Page 157: Matte Menu
Blue Color — adjusts the blue component of the key color, from 0 to 1024. • Red Threshold — adjusts the key’s clip along the Cyan vector (as demonstrated using a CIE color chip chart). ScreenPRO-II Controller • User’s Guide...
Page 158: Key Adjustment Menu
Working with Layers ” section on page 226 for instructions on using all types of keys. hÉó=pìÄ=jÉåìë The following sub menus can be accessed from the Key Adjustment Menu : • Matte Menu • Key Adjustment Menu ScreenPRO-II Controller • User’s Guide...
Page 159 Press { MIN } (if present) to change the highlighted color to 0 . • Press { MAX } (if present) to change the highlighted color to 1023 . • Press { BLACK } (if present) to change all three colors to 0 . ScreenPRO-II Controller • User’s Guide...
Page 160 Key Frame Effect — indicates the “motion type” that is used to move the Key from point to point. Note Only the Linear motion type is supported. All other key frame effects are ignored by ScreenPRO-II destinations. ScreenPRO-II Controller • User’s Guide...
Page 161 To return the Key to its default size and aspect ratio, press the RESET button in the Joystick Section . • To adjust the Key with fine resolution, press the FINE ADJUST button in the Joystick Section . ScreenPRO-II Controller • User’s Guide...
Page 162: Clone Setup Menu
For example, if you adjust H Position , both images move left and right. If you adjust V Position , both images move up and down. Cloned PIP A PIP A Figure 4-60. Clone Offset Mode ScreenPRO-II Controller • User’s Guide...
Page 163 Figure 4-61. Clone Mirror Mode • Offset — if “ Offset ” is selected on the Clone Type line, this field enables you to set the offset (in pixels). If “ Mirror ” is selected, the field is hidden. ScreenPRO-II Controller • User’s Guide...
Page 164: Crop Menu
Disable the function for individual parameter adjustments. Note To remove any crop effects from the PIP or Key, press the RESET button in the Joystick Section — while the Crop Menu is active. No other parameters will be affected. ScreenPRO-II Controller • User’s Guide...
Page 165: Source Adjustment Menus
4. Menu Orientation Source Adjustment Menus pçìêÅÉ=^ÇàìëíãÉåí=jÉåìë The following topics are discussed in this section: • Source Adjustment Menu Trees • Source Adjustment Menu Description • Source Adjustment Menu Functions ScreenPRO-II Controller • User’s Guide...
Page 166 Matte Image Effects Menu Menu Menu H Position V Position Move Rate Key Frame Effect Track Size STATS Figure 4-63. Source Adjustment Menu Trees All functions and sub menus are discussed in the following sections. ScreenPRO-II Controller • User’s Guide...
Page 167 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Move Rate Key Frame Effect [ Linear ] OPERATION: JOY Z TO SIZE, X Y TO POSITION TRACK SIZE Figure 4-65. Key Source Adjustment Menu (sample) ScreenPRO-II Controller • User’s Guide...
Page 168 Key Frame Effect — indicates the “motion type” that is used to move the PIP or Key from point to point. Note Only the Linear motion type is supported. All other key frame effects are ignored by ScreenPRO-II destinations. • At the bottom of each menu, the TRACK SIZE...
Page 169 To return the source to its default size and aspect ratio, press the RESET button in the Joystick Section . • To adjust the source with fine resolution, press the FINE ADJUST button in the Joystick Section . ScreenPRO-II Controller • User’s Guide...
Page 170: Background Input Setup Menu
The following topics are discussed in this section: • Background Input Setup Menu Tree • Shared Background Menu Functions • Background Menu Functions — Matte Type • Background Menu Functions — DVI Type • Background Menu Functions — FG Type ScreenPRO-II Controller • User’s Guide...
Page 171 HOME Crop: H Offset Crop: V Offset MATTE SAVE HOME SAVE RESET SAVE APPLY FORMAT FORCE ACQUIRE Figure 4-66. Background Input Setup Menu Tree All functions and sub menus are discussed in the following sections. ScreenPRO-II Controller • User’s Guide...
Page 172 Destination — displays the currently selected destination. Note that different backgrounds can be assigned to different destinations. • ID — displays the ID of the selected destination’s associated ScreenPRO-II. Note that with wide screen destinations, the background for each ScreenPRO-II can be individually adjusted.
Page 173 BG Matte Menu ” section on page 174 for details. • Press SAVE to store all selected background settings. In Chapter 6, refer to the “ Background Transitions ” section on page 227 for operating instructions. ScreenPRO-II Controller • User’s Guide...
Page 174 Figure 4-69. BG Matte Menu (sample) The Background Matte Menu enables you to create a solid background matte color to use behind your PIPs and Keys. Each ScreenPRO-II supports two separate matte colors — one for BG_A and one for BG_B .
Page 175 • Press { APPLY FORMAT } to “activate” the selected format. • Press { FORCE ACQUIRE } to automatically detect the input signal resolution and update the display Format field accordingly. ScreenPRO-II Controller • User’s Guide...
Page 176 Frame Grab Menu ” section on page 142 for details on the Frame Grab Menu . In Chapter 6, refer to the “ Working with Still Frames ” section on page 246 for frame grab instructions. ScreenPRO-II Controller • User’s Guide...
Page 177: Dsk Menus
Blue Mask STATS Opacity HOME SAVE SAVE MATTE HOME RESET STATS SAVE PICK COLOR APPLY FORMAT GRAB COLOR FORCE ACQUIRE Figure 4-72. DSK Menu Tree All functions and sub menus are discussed in the following sections. ScreenPRO-II Controller • User’s Guide...
Page 178 DSK type: • Destination — displays the currently selected destination. • ID — displays the ID of the selected destination’s associated ScreenPRO-II. • Invert Mode — enables you to invert the DSK signal. • Clip — adjusts the threshold of the video that electronically “cuts” into the background image.
Page 179 DSK type: • Destination — displays the currently selected destination. • ID — displays the ID of the selected destination’s associated ScreenPRO-II. • Red Color — adjusts the red component of the DSK color, from 0 to 1024. •...
Page 180 • Destination — displays the currently selected destination. • ID — displays the ID of the selected destination’s associated ScreenPRO-II. • DSK Input — displays the input connector from which the DSK source is pulled. ScreenPRO-II Controller • User’s Guide...
Page 181 • Type — selects the desired DSK type: When None is selected, the DSK circuitry for a selected ScreenPRO-II (as chosen with the ID field), can be turned off. This selection is recommended, for example, when a DSK is only required on one of three screens (in a wide screen configuration), and when only a single head graphics card would be required for the “active”...
Page 182: Logo Menu
File Name — displays the selected still frame’s temporary storage register. Resolution — displays the resolution of the selected still frame. Once you have reviewed all of the sections in this chapter, please continue with Chapter 5, “ System Setup ” on page 183. ScreenPRO-II Controller • User’s Guide...
Page 183: Setup Prerequisites
RK==póëíÉã=pÉíìé få=qÜáë=`Ü~éíÉê This chapter provides comprehensive instructions for setting up the ScreenPRO-II Controller system. The following topics are discussed: • Setup Prerequisites • System Setup Sequence • System Power Up • Return to Factory Default • Touch Screen Calibration •...
Page 184 5. System Setup Setup Prerequisites pÉíìé=mêÉêÉèìáëáíÉë Before starting to set up your ScreenPRO-II Controller system, please review the following important prerequisites: • Ensure that you are familiar with all ScreenPRO-II Controller system hardware, including all Controller sections, and the functions of all buttons within the sections.
Page 185: Id Setup And Remote Enable
5. System Setup System Setup Sequence póëíÉã=pÉíìé=pÉèìÉåÅÉ This section provides a top level view of the entire ScreenPRO-II Controller setup procedure, plus links to each individual procedure. Important For the optimum ScreenPRO-II Controller system setup, it is recommended that you follow all procedures in the order outlined below.
Page 186 On an individual ScreenPRO-II system, press { REMOTE CONTROL } on the Home Menu to access the Remote Control Menu . Scroll to the Unit ID line, and select a unique ID for the ScreenPRO-II chassis. The ID range is 1 to 32 .
Page 187 Power up all routers in your system, and allows them to fully boot up. These are your devices with static IP addresses. Power up the ScreenPRO-II Controller, and allow it to fully boot up. This is the system’s DHCP server.
Page 188 If required, press { PG DN } and { PG UP } to move between pages. • Press { DETAILS } to view additional information for a specific download. At the conclusion of the procedure, each ScreenPRO-II, PresentationPRO-II and BlendPRO-II is running the same version of code as the Controller. ScreenPRO-II Controller • User’s Guide...
Page 189 Return to Factory Default oÉíìêå=íç=c~Åíçêó=aÉÑ~ìäí ScreenPRO-II Controller system setup: Step 3 . In this procedure, you will perform a factory reset — in order to reset all router tables and source mappings. The procedure guarantees that any previous setups and presets (e.g., those that may have been programmed by other users), do not remain in system memory.
Page 190: Programming Edid
In this procedure, you will program EDID (Extended Display Identification Data), as a prerequisite for background and DSK setup. The procedure guarantees proper communications at the preferred resolution between each ScreenPRO-II’s DVI inputs and your system’s PCs. Prerequisite — Ensure that you are familiar with the EDID DVI Input Format Menu .
Page 191: Restore From Flash Memory Card
5. System Setup Restore from Flash Memory Card oÉëíçêÉ=Ñêçã=cä~ëÜ=jÉãçêó=`~êÇ ScreenPRO-II Controller system setup: Step 6 (optional) In this procedure, you will restore your system configuration from flash memory — provided that you previously backed up your system to the flash memory card.
Page 192: Standard Destination Setup
1 , 2 , 3 or 4 . Scroll to the SP to Add line and select the ID of an available ScreenPRO-II. If a ScreenPRO-II is already assigned to a destination, it will not appear in the list.
Page 193: Router Setup
” section on page 132. Use the following steps to set up your system’s routers: Ensure that your router(s) are properly connected to the ScreenPRO-II Controller system. In Chapter 3, refer to the “ System Installation ” section on page 73.
Page 194 If you are uncertain about the current patch, or if you want to remove the current (existing) patch and start clean, press { DELETE PATCH }. On the Device ID line, select the ScreenPRO-II ID to which you want to patch the selected router output.
Page 195: Aux Destination Setup
The ScreenPRO-II Controller system provides three types of Aux destinations — Aux , ImagePRO Aux and PrePRO-II Aux . Each type of destination can be switched from the ScreenPRO-II Controller by selecting it on the Destination Bus , then selecting the desired source on the Source Selection Bus .
Page 196: Aux Destination Setup
Aux 1 , Aux 2 , Aux 3 or Aux 4 . Scroll to the Type line and select ImagePRO Aux or PrePRO-II Aux . Press { AUX SETUP } to display the Aux Setup Menu . ScreenPRO-II Controller • User’s Guide...
Page 197 Destination Bus are now active. Please note: • For proper operation, ImagePRO and PrePRO-II devices must be connected to the ScreenPRO-II Controller via Ethernet. • ImagePRO and PrePRO-II output setups must be performed locally on the units themselves.
Page 198: Input Patching
You may not need to change the input patches if you want to use those already contained in the default Input Patch Table . The ScreenPRO-II Controller creates a unique “ Input Patch Table ” for each default router. After a factory reset, the table defaults to the following settings: Table 5-2.
Page 199: Output Format Setup
Chapter 4, refer to the “ Output Menu Functions ” section on page 102. In this procedure, you will configure the output format for each ScreenPRO-II that is used in your ScreenPRO-II Controller system. Important Be sure to select your projector’s native resolution and a frame rate that is consistent with your inputs —...
Page 200: Sync Setup
5. System Setup Sync Setup póåÅ=pÉíìé ScreenPRO-II Controller system setup: Step 12 Prerequisites — Ensure that you are familiar with the Settings Menu . In Chapter 4, refer to the “ Settings Menu ” section on page 104. In this procedure, you will set up sync parameters for the monitors and projectors connected to the system —...
Page 201: Genlock Setup
• For Single Screen Destinations — if you elect to connect an external genlock signal to ScreenPRO-II (and loop that signal from chassis to chassis), use this procedure to select the genlock “type” and verify the current setting of each ScreenPRO-II’s Termination Switch .
Page 202: Projector Setup
” section on page 106. Configurator Application . You can use the Configurator application to assist with wide screen setup. The software is available via download from the website, or contact Barco Technical Support . In Appendix B, refer to the “ Contact Information ”...
Page 203 WIDE SCREEN to display the Wide Screen Settings Menu . Note that the Total Projectors line shows the total number of ScreenPRO-II units that you defined in the wide screen configuration (on the Destination Setup Menu ). 11. Scroll to the Total H Res line and enter the total number of horizontal pixels in the overall wide screen display.
Page 204 When adjustments are complete, turn off the Alignment Test Pattern . 25. Press { BACK } to return to the Output Menu. 26. Press HOME to return to the Home Menu . 27. Press SAVE to save the new system configuration in memory. ScreenPRO-II Controller • User’s Guide...
Page 205: Background Setup
On the Destination Bus , select the destination whose background sources you want to configure. On the ScreenPRO-II Controller console, press BG A to display the Background Input Setup Menu . To configure a matte background: Scroll to the Type line and select Matte .
Page 206: Input Setup
On the Destination Bus , select the destination whose inputs you want to configure. On the ScreenPRO-II Controller console, select a layer ( LAYER A or LAYER B ). Press HOME to display the Home Menu .
Page 207: Color Balance Adjustments
Scroll to the Green Brightness line and adjust as required. • Scroll to the Blue Contrast line and adjust as required. • Scroll to the Blue Brightness line and adjust as required. • Press { SAVE } to save the input configuration. ScreenPRO-II Controller • User’s Guide...
Page 208 You do have to repeat the input setup procedure if either of the following criteria are met: • Your other destinations use a different router. • Your other destinations use unique input patching. 14. If required, repeat the entire procedure from step 1 for other destinations. ScreenPRO-II Controller • User’s Guide...
Page 209 Turn the Modify Layers on Program function to On . On the Destination Bus , select your widescreen destination. On the ScreenPRO-II Controller console, select LAYER A . On the Source Selection Bus , select the first source that you want to set up.
Page 210 20. Repeat steps 13 through 19 for all remaining widescreen destinations. 21. When complete, clear the layer and transition it off program. 22. On the ScreenPRO-II Controller console, select LAYER B . 23. Repeat the entire procedure from step 6 — for the same source.
Page 211: Dsk Setup Procedure
On the Destination Bus , select the destination whose DSK source you want to configure. On the ScreenPRO-II Controller console, press DSK to display the DSK Adjustment Menu . Press { INPUT SETUP } to display the DSK Input Setup Menu .
Page 212: Logo Setup Procedure
Use the following steps to set up the LOGO: On the Destination Bus , select the destination whose LOGO you want to configure. On the ScreenPRO-II Controller console, press LOGO to display the LOGO Menu . To configure a black LOGO: Scroll to the Type line and select Black .
Page 213: Saving The Setup
5. System Setup Saving the Setup p~îáåÖ=íÜÉ=pÉíìé ScreenPRO-II Controller system setup: Step 19 When all system setup procedures have been complete, press { HOME } to display the Home Menu , then press SAVE . This action saves the state of the Controller in non- volatile memory.
Page 214: Backup To Flash Memory Card
5. System Setup Backup to Flash Memory Card ScreenPRO-II Controller • User’s Guide...
Page 215: Prerequisites
SK==léÉê~íáçåë få=qÜáë=`Ü~éíÉê This chapter includes operational instructions for all ScreenPRO-II Controller modes and functions. The following topics are discussed: • Prerequisites • Operational Configuration • Working with Destinations • Working with Layers • Working with Layer Functions • Using Move •...
Page 216 6. Operations Prerequisites mêÉêÉèìáëáíÉë Prior to using the ScreenPRO-II Controller system, please ensure the following: • All system inputs, backgrounds, the DSK and the LOGO are properly configured. In Chapter 5, refer to the following sections for details: “ Input Setup "...
Page 217: Monitor Layout
Press { LCD SETTINGS } to display the first LCD Settings Menu . Press { LCD Cal } to display the first Touch Screen Calibration Menu . Follow directions on screen to complete the calibration procedure. ScreenPRO-II Controller • User’s Guide...
Page 218 Images between the two vertical green lines are projected. Images outside of the lines are not. Preview #1 Preview #2 Wide Wide Screen Screen Preview #1 Preview #2 Marker Marker Figure 6-3. Wide Screen Marker, Center Justification ScreenPRO-II Controller • User’s Guide...
Page 219 Operational Configuration iççâ~ÜÉ~Ç=mêÉîáÉï The ScreenPRO-II Controller uses a “lookahead” preview system that ensures the accuracy of all your transitions. The “look” or appearance that you create on Preview represents the exact appearance of Program — after you transition the images to Program.
Page 220 6. Operations Operational Configuration råÇÉêëí~åÇáåÖ=o~ëíÉê=_çñÉë With ScreenPRO-II Controller, Raster Boxes are always enabled on Preview, each PIP or Key is surrounded by a thin border that helps you identify the PIP or Key’s original layer. • The PIP or Key with a red “corner” style raster box is Layer A .
Page 221 ^=tçêÇ=^Äçìí=ilp On rare occasion, you can experience LOS (loss of signal) — typically due to a poor video, graphics or computer connection. In these cases, the ScreenPRO-II Controller obeys a precise set of rules for how to handle the signals: •...
Page 222: Working With Destinations
• When you press a single button or a group of buttons, your selection is mutually exclusive with all other active destinations. • Press the All button to turn all destinations on. ScreenPRO-II Controller • User’s Guide...
Page 223 Enable all destinations that you want to transition. Perform the desired transition in the normal manner. Once performed, the pending route is completed. Note If you want to clear the pending route prior to performing it, simply clear the lit Aux destination(s). ScreenPRO-II Controller • User’s Guide...
Page 224 Route Source 3 to Destinations 1 and 2 , and Aux Destinations 1 and 2 : Turn DEST AUX off. Press Destinations 1 and 2 simultaneously. Press LAYER A . Turn DEST AUX on. Press Destinations 1 and 2 simultaneously. ScreenPRO-II Controller • User’s Guide...
Page 225 Double-punch the ALL button to clear all destinations. Turn DEST AUX on. Press Destinations 3 and 4 simultaneously. Select Source 7 . Turn DEST AUX off. Press Destinations 1 and 2 simultaneously. Press AUTO TRANS . ScreenPRO-II Controller • User’s Guide...
Page 226: Working With Layers
Use the SHIFT button to access sources 9 through 16 . • The SDI 1 and SDI 2 buttons are only active when a ScreenPRO-II is configured to use internal routing . The buttons are disabled when external routing is used.
Page 227 The similar situation is true for BG B . • If BG A is on Program and BG B is selected in Preview, BG A will transition to BG B on the next transition. ScreenPRO-II Controller • User’s Guide...
Page 228 6. Operations Working with Layers råÇÉêëí~åÇáåÖ=péäáí=~åÇ=jáñ=jçÇÉë The ScreenPRO-II Controller provides two different modes with which you can transition PIPs and Keys: • Split Mode • Mix Mode péäáí=jçÇÉ With the Split button lit, the mixer’s two layers operate independently . You can size,...
Page 229 Press the desired layer button ( A or B ). Please note: The layer button blinks to indicate that it is active for modification. In the Source Selection Bus , the source assigned to the layer blinks. ScreenPRO-II Controller • User’s Guide...
Page 230 153 for details. Global Functions — Remember that the following global functions are always available: Press Reset (in the Joystick Section ) to reset the current effect (e.g., PIP, Key, crop, etc.) to a nominal default value. ScreenPRO-II Controller • User’s Guide...
Page 231 Press CUT or AUTO TRANS to transition the look to Program. Refer to the “ Working with Transitions " section on page 241 for details. Repeat the procedure from step 1 for the next transition. ScreenPRO-II Controller • User’s Guide...
Page 232 Use the Clip , Gain and Opacity controls to set the appearance of the fill video as desired. Alternate between selecting Layer A and Layer B , and use each layer’s Size and Position controls to position the fill within the key as desired. ScreenPRO-II Controller • User’s Guide...
Page 233 Matte Menu , press { EFX } to display the Image Effects Menu . Select the desired effect, including monochrome, chroma and hue, invert and strobe. In Chapter 4, refer to the " Image Effects Menu " section on page 153 for details. ScreenPRO-II Controller • User’s Guide...
Page 234 Program. jçÇáÑóáåÖ=i~óÉêë=lå=mêçÖê~ã The ScreenPRO-II Controller enables you to modify layers directly on Program, without first setting up a "look" on Preview. The mode is typically used for creating and viewing a "look" on Program (especially in conjunction with a large screen projector) when the Preview monitor may be too small to realize the desired result.
Page 235: Working With Layer Functions
Ensure that the PIP or Key is positioned fully within the boundaries of an outside destination’s screen. If the PIP or Key straddles the widescreen overlap region, the mode cannot be enabled. Press Clone to display the Clone Setup Menu . ScreenPRO-II Controller • User’s Guide...
Page 236 If a source is on Program, selecting its layer and pressing Freeze will freeze the image on Program. • You can also use Freeze if the PIP or Key is only on Preview, and then transition the frozen image to Program. ScreenPRO-II Controller • User’s Guide...
Page 237 Transition the new "look" to program with a CUT or AUTO TRANS . To exit the mode, transition the effect off Program and back to Preview. Press and hold the Split button, then press either of the two layer buttons. ScreenPRO-II Controller • User’s Guide...
Page 238: Using Move
• Move Notes mêçÖê~ããáåÖ=jçîÉë The ScreenPRO-II Controller enables you to move a PIP or a Key (or both) smoothly from one screen location to another at a predefined rate, while the layer(s) are on-air. All moves Move are two-keyframe effects, with a starting location and an ending (destination) location.
Page 239: Program A Move On Program
To move the layer back to keyframe 1, press Move . The button lights and on Preview, the raster box blinks at the "starting" location. Perform a CUT or AUTO TRANS . In this "ping-pong" manner, you can continue to transit back and forth between keyframes 1 and 2. ScreenPRO-II Controller • User’s Guide...
Page 240 Move Setup twice. • On screen, off screen — The ScreenPRO-II Controller enables you to move a PIP or Key from an off-screen location to an on-screen location, and vice-versa. Remember that Move behaves differently, depending on the selected mode: •...
Page 241: Working With Transitions
Press { HOME } > { EFFECTS } to display the Effects Menu . Adjust the Transition Rate field for the desired rate, in 0.1 second increments. Adjust the Transition Wipe field for the desired wipe pattern. ScreenPRO-II Controller • User’s Guide...
Page 242 In the Transition Section , move the T-Bar to manually dissolve (or wipe) the images on Preview to Program. qê~åëáíáçå=kçíÉë Using the Effects Menu , transitions performed on the ScreenPRO-II Controller are destination-based. Two examples are provided below. Select destinations 1 and 3, then press WIPE . Next, select destination 2 only and press MIX .
Page 243: Working With Presets
Working with Presets tçêâáåÖ=ïáíÜ=mêÉëÉíë This section provides detailed instructions for working with Presets. The ScreenPRO-II Controller’s Preset Section enables you to store and recall entire Controller setups. Each preset button represents one “look” of the overall projected image. The Controller has 6 Preset buttons and 6 "page"...
Page 244 In the Preset Section , press Next to recall the next valid Preset in sequential order. Please note: If Preset 2 is lit, pressing Next recalls Preset 3 . If Preset 6 is active on page 2 , pressing Next advances to Preset 1 on page 3 . ScreenPRO-II Controller • User’s Guide...
Page 245 "end" points — all of which use the end point from the previous Preset as their new starting point. If you recall a Preset with a defined Move to an empty layer, both the starting and ending points of the recalled Move will be used. ScreenPRO-II Controller • User’s Guide...
Page 246: Working With Still Frames
The ScreenPRO-II Controller enables you to capture still frames into each ScreenPRO-II’s three internal frame stores. The “sources” of the still frames are each ScreenPRO-II’s BG A and BG B inputs, or the scaled inputs ( Layer A or B ).
Page 247 Note The layer can be on Program or Preview. Select PIP or Key in the normal manner. The selected PIP or Key Adjustment Menu appears. Adjust the PIP or Key’s size and position. Remember that: ScreenPRO-II Controller • User’s Guide...
Page 248: Capturing Still Frames From A Background Input
Press NO to cancel the procedure. If required, press { DELETE } to delete the selected frame from permanent storage. This button only appears when frames are stored in permanent memory. ScreenPRO-II Controller • User’s Guide...
Page 249 Press Enter (on the PS-2 keyboard) to save the name. Once saved, the system "attaches" the name to the still in permanent memory. Press { BACK } to return to the Frame Grab Menu . ScreenPRO-II Controller • User’s Guide...
Page 250: Using The Dsk
In the Layer Control Section , press DSK to display the DSK Adjustment Menu . Press { INPUT SETUP } to display the DSK Input Setup Menu . On the ID line, select the ID of the ScreenPRO-II with which you want to perform the DSK.
Page 251: Using The Logo
"look." • After a transition, the LOGO layer is automatically cleared from Preview. In this way the next transition will always fade up from black to your previous setup. ScreenPRO-II Controller • User’s Guide...
Page 252: Locking And Unlocking The Controller
If you have selected a Custom lockout code, but you have forgotten the code, a Master Code is available. Refer to the ScreenPRO-II Controller system’s most current " Whatsnew_ScreenPRO-II Controller.txt " document for details. This document is bundled with every software download.
Page 253: Working With Tallies
Tally functionality can be tested. Press { HOME } > SYSTEM > { DIAG } > { TALLY } to initiate the test. rëáåÖ=_~Åâìé=~åÇ=oÉëíçêÉ The ScreenPRO-II Controller system enables you to backup and restore the complete system setup including all Presets, using a customer supplied flash memory card. The following topics are discussed: •...
Page 254 When restoring, you must have the same version of software installed in the Controller as was used to perform the backup. • Conversion between versions can only be done with the Barco Backup and Restore utility. Note The Barco Backup and Restore utility can be found in the ScreenPRO-II Controller software bundle —...
Page 255: Screenpro-Ii Input Specifications
^K==péÉÅáÑáÅ~íáçåë få=qÜáë=^ééÉåÇáñ This appendix provides detailed technical specifications for the ScreenPRO-II Controller. The following topics are provided: • ScreenPRO-II Input Specifications • ScreenPRO-II Output Specifications • User Control • Widescreen Functions • Physical and Electrical Specifications • Communications Specifications •...
Page 256 ^K==péÉÅáÑáÅ~íáçåë ScreenPRO-II Input Specifications pÅêÉÉåmolJff=fåéìí=péÉÅáÑáÅ~íáçåë= The table below lists input specifications for individual ScreenPRO-II units. Table A-1. ScreenPRO-II Input Specifications Parameter Specification Scaled Channel Inputs Analog inputs (8) — RGBHV / RGBS / RGsB computer video, YPbPr video (SD or HD), S-video, or composite video on 15-pin HD connector SD and HD-SDI Input (2 optional) —...
Page 257 ^K==péÉÅáÑáÅ~íáçåë ScreenPRO-II Output Specifications pÅêÉÉåmolJff=lìíéìí=péÉÅáÑáÅ~íáçåë= The table below lists output specifications for individual ScreenPRO-II units. Table A-2. ScreenPRO-II Output Specifications Parameter Specification Analog Outputs RGBHV / RGBS / RGsB (non-interlaced only) on 15-pin HD connectors Preview and two Program monitor / projector outputs Digital Outputs Digital DVI per DDWG 1.0 on DVI-I connector (Program output)
Page 258: Widescreen Functions
Same as Encore Note * Additional BlendPRO-II units connected to the ScreenPRO- II Controller system will not be recognized. mÜóëáÅ~ä=~åÇ=bäÉÅíêáÅ~ä=péÉÅáÑáÅ~íáçåë= The table below lists ScreenPRO-II Controller physical and electrical specifications. Table A-5. ScreenPRO-II Controller Physical and Electrical Specifications Parameter Specification Power 120-240 VAC - 50/60 Hz., Auto-selecting 1.0A maximum...
Page 259: Communications Specifications
0.25" (0.63 cm) 1.22" (3.09 cm) 11.50" (29.21 cm) 12.72" (32.30 cm) Figure A-1. ScreenPRO-II Controller Side View `çããìåáÅ~íáçåë=péÉÅáÑáÅ~íáçåë= The table below lists ScreenPRO-II Controller communications specifications. Table A-6. ScreenPRO-II Controller Communications Specifications Parameter Specification Ethernet RJ-45, 10/100 Mbps Autosense...
Page 260: Pinouts
Ethernet Connector • Serial Connector • Tally Connector bíÜÉêåÉí=`çååÉÅíçê The figure below illustrates the ScreenPRO-II Controller Ethernet connector: Figure A-2. Ethernet Connector The table below lists Ethernet connector pinouts. Table A-7. Ethernet Connector Pinouts Signal Wire Color TX Data +...
Page 261 ^K==péÉÅáÑáÅ~íáçåë Pinouts pÉêá~ä=`çååÉÅíçê The figure below illustrates the ScreenPRO-II Controller serial connector, which is used for both the Ext Comm and Console Port connections. Figure A-3. Serial Connector The table below lists Serial connector pinouts. Table A-8. Serial Connector Pinouts...
Page 262 Tally 6 contact closure Tally 6 grounding closure Tally 6 contact closure Tally 7 contact closure Tally 7 grounding closure Tally 7 contact closure Tally 8 contact closure Tally 8 grounding closure Tally 8 contact closure Signal ground ScreenPRO-II Controller • User’s Guide...
Page 263: Screenpro-Ii Input And Output Resolutions
This section provides a comprehensive list of available input and output resolutions on the individual ScreenPRO-II units. These resolutions can be assigned to the selected input on the Input Menu , and as the system’s output format on the Output Menu . In Chapter 4, refer to the “...
Page 264 ^K==péÉÅáÑáÅ~íáçåë ScreenPRO-II Input and Output Resolutions • 1024x768 @75 • 1024x768 @85 • 1152x864 @75 • 1280x768 @47.95 • 1280x768 @48 • 1280x768 @50 • 1280x768 @59.94 • 1280x768 @75 • 1280x960 @50 • 1280x960 @59.94 • 1280x960 @60 •...
Page 265 ^K==péÉÅáÑáÅ~íáçåë ScreenPRO-II Input and Output Resolutions • 1600x1200 @50 • 1600x1200 @59.94 • 1600x1200 @60 • 1280x720p @50 • 1280x720p @59.94 • 1280x720p @60 • 1920x1080p @23.98 • 1920x1080p @24 • 1920x1080p @25 • 1920x1080p @29.97 • 1920x1080p @30 •...
Page 266 ^K==péÉÅáÑáÅ~íáçåë ScreenPRO-II Input and Output Resolutions ScreenPRO-II Controller • User’s Guide...
Page 267: In This Appendix
Warranty related repairs include parts and labor, but do not include faults resulting from user negligence, special modifications, lightning strikes, abuse (drop/crush), and/or other unusual damages. The customer shall pay shipping charges when unit is returned for repair. Barco will cover shipping charges for return shipments to customers. oÉíìêå=j~íÉêá~ä=^ìíÜçêáò~íáçå=Eoj^F...
Page 268: Contact Information
BELGIUM • Phone: +32 56.36.82.11 • Fax: +32 56.35.16.51 • Website: www.events.barco.com Technical Support / Customer Service Information • Tech Line: (866) 374-7878 — 24 hours per day, 7 days per week • E-mail: folsomsupport@barco.com ScreenPRO-II Controller • User’s Guide...
Page 269: Software Upgrade Overview
`K==réÖê~ÇáåÖ=pçÑíï~êÉ få=qÜáë=^ééÉåÇáñ The following topics are discussed in this Appendix: • Software Upgrade Overview • Hardware Requirements • Software Requirements • Downloading Software • Serial Upgrade Method • Ethernet Upgrade Method ScreenPRO-II Controller • User’s Guide...
Page 270: Downloading Software
All software files listed above (and more) are contained in the file that you will download. Software files can be downloaded from either the Folsom FTP site or the Barco Folsom website, as described in the following “ Downloading Software ”...
Page 271: Via Ftp Site
`K==réÖê~ÇáåÖ=pçÑíï~êÉ Downloading Software açïåäç~ÇáåÖ=pçÑíï~êÉ Two different methods can be used to download ScreenPRO-II Controller software and the Flash File Loader utility: • Via FTP Site • Via Web Site sá~=cqm=páíÉ Barco Folsom's FTP site address is: ftp.folsom.com To download from the FTP site: Create a target folder on your PC (e.g., ScreenPRO-II Controller).
Page 272: Serial Upgrade Method
Follow the prompts to install the upgrade package. At the conclusion of the procedure, a new path will be created under Start > Programs > Barco Folsom . Connect the Console port on the back of the ScreenPRO-II Controller to the COM 1 port on your PC.
Page 273 Repeat steps 7 and 8 above, then re-check the status lights. With communication status OK, continue with step 10 . 10. To upload files to ScreenPRO-II Controller, click " Open script file to read and upload ." 11. In the dialog, select " Complete_Load.sld " and click Open . The ScreenPRO-II Controller menu should immediately display the "...
Page 274: Ethernet Upgrade Method
IP connections to the outside world. Power-up the ScreenPRO-II Controller. On the PC, click Start > Programs > Barco Folsom > ScreenPRO-II Controller Software #.## > Flash Loader to launch the Flash Loader utility. Figure C-2. Flash Loader Utility Click Communication >...
Page 275: Troubleshooting Ethernet Communication
Troubleshooting Ethernet Communication ” section on page 275. To upload files to the ScreenPRO-II Controller, click " Open script file to read and upload ." 10. In the dialog, select " Complete_Load.sld " and click Open . The ScreenPRO-II Controller menu should immediately display the " System in LOADER MODE "...
Page 276 `K==réÖê~ÇáåÖ=pçÑíï~êÉ Ethernet Upgrade Method If you see a “ Request timed out ” message, the PC is unable to locate and communicate with the ScreenPRO-II Controller. If this is the case: • Check your network connections and settings as described above, or ...
Page 277 1-1 Sizing Menu ......95 {LCD CAL} ......139 ScreenPRO-II Controller • User’s Guide...
Page 279 Aux destinations ....72 Configure ScreenPRO-II outputs ..101 blank, DVI connection ....70 Connection blank, external routing, analog router I/O .66...
Page 281 ......82 Features, ScreenPRO-II Controller ..20 Feet, adjustable .
Page 282 ......103 install ScreenPRO-II Controller ..73 termination ......76 lock controller .
Page 283 PIPs in split mode ....229 use previous ..... .245 ScreenPRO-II Controller • User’s Guide...
Page 287 PrePRO-II ScreenPRO-II Controller ... . .20 Aux ......120 software upgrade .
Page 291 Touch screen ..... . .19, 38 calibration ....76, 189, 217 ScreenPRO-II Controller • User’s Guide...
Page 292 Keys in split mode ....231 PIPs in mix mode ....229 ScreenPRO-II Controller • User’s Guide...

Barco ScreenPRO-II User Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Barco ScreenPRO-II

Summary of Contents for Barco ScreenPRO-II

Table of Contents