Planet FT-801 User Manual

Planet FT-801 User Manual

Fast ethernet converter, multi-mode and single-mode
Hide thumbs Also See for FT-801:

Advertisement

Copyright
Copyright © PLANET Technology Corp. 2004.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technol-
ogy Corp. The information in this manual is subject to
change without notice. All other trademarks belong to
their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware
will work properly in all environments and applications,
and makes no warranty and representation, either
implied or expressed, with respect to the quality, per-
formance, merchantability, or fitness for a particular
purpose.
PLANET has made every effort to ensure that this User's
Manual is accurate; PLANET disclaims liability for any
inaccuracies or omissions that may have occurred.
Information in this User's Manual is subject to change
without notice and does not represent a commitment on
the part of PLANET. PLANET assumes no responsibility
for any inaccuracies that may be contained in this User's
Manual. PLANET makes no commitment to update or
keep current the information in this User's Manual, and
reserves the right to make improvements to this User's
Manual and/or to the products described in this User's
Manual, at any time without notice.
If you find information in this manual that is incorrect,
misleading, or incomplete, we would appreciate your
comments and suggestions.

FCC Warning

This equipment has been tested and found to comply
with the regulations for a Class A digital device, pur-
suant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated in
a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FT-801 and is the answer not in the manual?

Questions and answers

Summary of Contents for Planet FT-801

  • Page 1: Fcc Warning

    All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, per- formance, merchantability, or fitness for a particular purpose.
  • Page 2 Revision User’s manual for PLANET Fast Ethernet Converter Multi-mode: FT-801, FT-802, FT-803 Single-mode: FT-802S15, FT-802S35, FT-802S50, FT-806A20, FT-806B20 Rev 6.0 (September. 2004)
  • Page 3: Table Of Contents

    Table of Contents Chapter 1 Overview Chapter 2 Model List Chapter 3 Checklist Chapter 4 Product Outlook Chapter 5 Link Fault Pass through (LFP) Chapter 6 Installing the Converter Chapter 7 Duplex Mode setting Chapter 8 LED indication Chapter 9 Cable Connection Parameter Chapter 10 FT-80X Technical Specifications Chapter 11 Power information...
  • Page 5: Chapter 1 Overview

    Model List Your Fast Ethernet Converter comes with one of the following models. ð FT-801: on board ST fiber connector ð FT-802/S: on board SC fiber connector ð FT-803: on board MTRJ fiber connector ð FT-806A20: on board single SC fiber connector ð...
  • Page 6: Chapter 3 Checklist

    Chapter 3 Checklist Your FT-80X carton should contain the following items: ð The Fast Ethernet Bridge Converter ð AC-DC Power Adapter (Output: 5VDC, 2 A max.) ð This user’s manual If any item is missing or damaged, please consult the dealer from whom you purchased your Fast Ethernet Converter.
  • Page 7: Chapter 5 Link Fault Pass Through (Lfp)

    Side View (FT-80X) One DIP switch for Link Fault Pass Through (LFP) feature, “ON” to turn-on the LLCF and LLR detection. And “OFF” to turn–off this feature. Please refer to the following sections for more. DIP Switch for LFP function. Chapter 5 Link Fault Pass through (LFP) The LFP function includes the Link Fault Pass Through function...
  • Page 8 Link Loss Carry Forward (LLCF) FT-80X incorporates an LLCF function for troubleshooting a remote connection. When LFP function is enabled, the FL/TP ports do not transmit a link signal until they receive a link signal from the opposite port. The diagram below shows a typical network configuration with a good link status using FT-80X for remote connectivity.
  • Page 9 If one of the optical conductors is bad (as shown in the diagram box below), the converter with LLR function will return a no-link condition to its link partner. With LLCF function also enabled, the no-link condition is carried forward to the switch/hub where a trap is generated to the management station, and the administrator can then determine the source of the loss.
  • Page 10: Chapter 6 Installing The Converter

    Chapter 6 Installing the Converter Please follow these steps to install the converter: • Turn off the power of the device/station in a network to which the FT-80X will be attached • Ensure that there is no activity in the network •...
  • Page 11: Chapter 7 Duplex Mode Setting

    Chapter 7 Duplex Mode setting The TP port of FT-80X supports duplex mode detection by auto- negotiation (A-N). The following is the duplex mode parameters: Fast Ethernet Device FT-80X Duplex Mode support Ethernet / Fast Ethernet Hub Half-Duplex Ethernet / Fast Ethernet Switch Half-Duplex (without A-N) Fast Ethernet Devices *...
  • Page 12: Chapter 8 Led Indication

    Chapter 8 LED indication Color Description FX LNK Green Blinks: when any FX packets transmit- / ACT ting and receiving Lit: when Fiber connection is good TX LNK Green Blinks: when any TP packets transmit- / ACT ting and receiving Lit: when TP connection is good FX FDX/ Green...
  • Page 13: Chapter 9 Cable Connection Parameter

    Chapter 9 Cable Connection Parameter The limitations are as below: Duplex Connection Limitation (max.) Twisted Pair Node to Node Half / Full 100 meters Node to Switch/Hub Multi-Mode Converters Node to Node MM Half 412 meters Node to Switch Node to Node MM Full 2 kilometers Node to Switch...
  • Page 14: Chapter 10 Ft-80X Technical Specifications

    Chapter 10 FT-80X Technical Specifications The FT-80X comes with the following standard features: · Standard: IEEE802.3/u, 10/100Base-TX and 100Base- · Connectors: ð One RJ-45 (Auto-MDI/MDI-X) Twisted Pair, EIA568 ð One Fiber-optic, 1310nm wavelength (except: FT- 806A/FT-806B), connector-type vary with model ·...
  • Page 15: Chapter 11 Power Information

    Chapter 11 Power information The power jack of FT-80X is with 2.5mm in the central post and required +5VDC power input. It will conform to the bundled AC- DC adapter and Planet’s Media Chassis. Should you have the problem to make the power connection, please contact your local sales representative.
  • Page 16 This page is intentionally left blank...
  • Page 18 2010-000002-005...

Table of Contents