Venstar T1700 Installation Instructions Manual
Residential 1-day programmable up to 2-heat & 1-cool
Hide thumbs
Also See for T1700:
- Owner's manual (79 pages) ,
- Specification (1 page) ,
- Calibration manual (4 pages)
Advertisement
Digital
Digital
Thermostat
Thermostat
CONFIGURABLE IN SETUP:
Auto or Manual changeover
Programmable or
Non-Programmable
Use with most Air Conditioning & Heating Systems including: 1 or 2 Stage
Electric Cooling & 3 Stage Gas Heating, Heat Pump, Electric or Hydronic Heat.
INSTALLATION
INSTALLATION
INSTRUCTIONS
INSTRUCTIONS
Venstar Inc. 08/07
residential
THERMOSTAT
T1 700
1-DAY
1-DAY
PROGRAMMABLE
PROGRAMMABLE
up to
2-heat
up to
2-heat
& 1-cool
& 1-cool
HEAT
HEAT
COOL
PUMP
Control up to 2 Heat &
1 Cool Stages
Backlit Display & Button
Legends
Aux Heat Indicator
Outdoor Sensor Ready
Accepts EZ Programmer
Accepts Optional IR
Remote Control
Accepts Comfort Call
Phone Control Accessory
Advertisement
Related Manuals for Venstar T1700
Summary of Contents for Venstar T1700
- Page 1 Remote Control Accepts Comfort Call Phone Control Accessory Use with most Air Conditioning & Heating Systems including: 1 or 2 Stage Electric Cooling & 3 Stage Gas Heating, Heat Pump, Electric or Hydronic Heat. INSTALLATION INSTALLATION INSTRUCTIONS INSTRUCTIONS Venstar Inc. 08/07...
- Page 2 (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Thermostat T1700 Tested to Comply with FCC Standards FOR HOME OR OFFICE USE...
-
Page 4: Table Of Contents
Table of Contents Preparation Remove & Replace the Old Thermostat Wire Connections Sample Wiring Diagrams Test Operation Calibrating the Thermostat Sensors TroubleShooting Page... -
Page 5: Preparation
SECTION 1 Preparation Proper installation of the thermostat will be I2:00 accomplished by following these step by step AUTO instructions. If you are unsure about any of these steps, call a qualified technician for assistance. Assemble tools I2:00 AUTO Flat Blade Wire cutter Screwdriver &... -
Page 6: Remove & Replace The Old Thermostat
SECTION 2 Remove & Replace the Old Thermostat Remove the cover of the old thermostat. I2:00 AUTO If it does not come off easily check for screws. Loosen the screws holding the thermostat I2:00 AUTO base or subbase to the wall, and lift away. Disconnect the wires from the old thermostat. -
Page 7: Wire Connections
SECTION 3 Wire Connections If the terminal designations on your old I2:00 AUTO thermostat do not match those on the new thermostat, refer to the chart below, or the wiring diagrams that follow. Wire from the Install on the new thermostat old thermostat Function connector marked... -
Page 8: Sample Wiring Diagrams
SECTION 4 Sample Wiring Diagrams Section 4 Contents: HVAC Equipment Wiring....4.2 Installing the Outdoor Sensor..4.6 Page 4.1... - Page 9 6 Wire, 1 Stage Cooling, 1 Stage Heat Residential & Commercial 1 Stage Cooling, Commercial Heat Pump 1 Stage Cooling with 1st stage Gas Heat with 2 Stage Heat W1/O/B RS+5 RSGND ELEC 6 Conductor 18 gauge ELEC unshielded cable from the thermostat to the equipment.
- Page 10 6 Wire, 1 Stage Cooling, 1 Stage Heat Residential & Commercial 1 Stage Cooling, with 1st stage Electric Heat W1/O/B RS+5 RSGND ELEC 6 Conductor 18 gauge ELEC unshielded cable from the thermostat to the equipment. RS+5 RSGND 24 vac common 24 vac return fan relay compressor relay...
- Page 11 6 Wire, 1 Stage Cooling, 2 Stage Heat Residential Heat Pump with O Reversing Valve 1 Stage Cooling, with 2 stage Heat W1/O/B RS+5 RSGND ELEC 6 Conductor 18 gauge ELEC unshielded cable from the thermostat to the equipment. RS+5 RSGND 24 vac common 24 vac return...
- Page 12 6 Wire, 1 Stage Cooling, 2 Stage Heat Residential Heat Pump with b Reversing Valve 1 Stage Cooling, with 2 stage Heat W1/O/B RS+5 RSGND ELEC 6 Conductor 18 gauge ELEC unshielded cable from the thermostat to the equipment. RS+5 RSGND 24 vac common 24 vac return...
- Page 13 Installing the Outdoor Sensor The Outdoor Sensor measures outdoor air temperature and sends this information to the thermostat; it measures temperature with a range of -40 to 127 F. The Outdoor Sensor should be connected to the thermostat using solid conductor CAT 5, CAT 5e, or CAT 6 type network communication cable.
-
Page 14: Test Operation
SECTION 5 Test Operation Turn the power on to the Heating/Air Conditioning I2:00 AUTO system. Press the MODE button repeatedly until the I2:00 AUTO HEAT icon appears on the display. Press Up or Down buttons until the set temperature is 10 degrees above room temperature. -
Page 15: Calibrating The Thermostat Sensors
SECTION 6 Calibrating the Thermostat Sensors Under normal circumstances it will not be necessary to adjust the calibration of the temperature and humidity sensors. If calibration is required, please contact a trained HVAC technician to correctly perform the following procedure. I2:00 Place the thermostat in the MODE... -
Page 16: Troubleshooting
SECTION 7 TroubleShooting SYMPTOM: The air conditioning does not attempt to I2:00 turn on. AUTO CAUSE: The compressor timer lockout may prevent the air conditioner from turning on, for a period of time. REMEDY: Consult the Owner's Manual in the Setup section to defeat the cycles per hour and compressor timeguard. - Page 17 TroubleShooting SYMPTOM: When controlling a residential heat pump, I2:00 AUTO and asking for cooling, the heat comes on. CAUSE: The thermostat reversing valve jumper is set for “b”. REMEDY: Set the reversing valve jumper for “O”. See pages 5.4 and 5.5. SYMPTOM: When calling for cooling, both the heat I2:00 AUTO...
Need help?
Do you have a question about the T1700 and is the answer not in the manual?
Questions and answers
need to replace batteries T1700
The Venstar T1700 thermostat does not appear to use batteries. If the screen is blank, it may have lost power. Check the circuit breaker to restore power.
This answer is automatically generated
HOW TO REPLACE BATTERIES
The Venstar T1700 thermostat does not use batteries. If the screen is blank, it may have lost power. Check the circuit breaker to restore power.
This answer is automatically generated
HOW DO I OPEN TO REPLACE BATTERIES
The provided context does not mention how to open the Venstar T1700 thermostat or if it even uses batteries. However, it does suggest that this thermostat may not use batteries and that a blank screen could indicate a power loss. You may want to check the circuit breaker instead.
This answer is automatically generated