Tech 21 SansAmp PSA-1 User Manual
  1. Manuals
  2. Brands
  3. Tech 21 Manuals
  4. Amplifier
  5. SansAmp PSA-1
  6. User manual

Tech 21 SansAmp PSA-1 User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

L
P U S H 2 X
PUNCH
CRUNCH
DRIVE
LOW
HIGH
P R O G R A M M A B L E
INPUT
PSA-1
U S E R S G U I D E
TM
LEVEL
DOWN
P U S H 2 X
PRE - AMP
BUZZ
PUNCH
CRUNCH
DRIVE
P R O G R A M M A B L E
TM
UP
TM
LOW
HIGH
LEVEL
PRE - AMP
BUZZ
PUNCH
P
M O D E L
TM
PSA-1

TABLE OF CONTENTS

Programming
Low and High
Down switch and Up switch
0dB and -10dB positions
Left & right returns
MIDI In and MIDI Thru/Out
Using the Effects Loop
Function 1: Custom Preset Data Dump
Function 4: Fixed/Programmable Swap Bit
List of Presets and List of Custom Settings
Warranty Information
1
2
2
3
4
4
5
5
6
6
6
7
7
7
7
7
7
8
8
9
9
9
9
9
9
9
9
10
10
10
10
10
11
11
11
11
11
12
13
13
14
15
16
16
18
19
20
20
21
21
21
22
24
Back Cover
Back Cover

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SansAmp PSA-1 and is the answer not in the manual?

Questions and answers

Related Manuals for Tech 21 SansAmp PSA-1

Summary of Contents for Tech 21 SansAmp PSA-1

  • Page 1: Table Of Contents

    XLR output level switch P R O G R A M M A B L E Footswitch MIDI In and MIDI Thru/Out Suggested Setups Using the SansAmp PSA-1’s Inputs Using the SansAmp PSA-1’s Outputs INPUT PRE - AMP BUZZ PUNCH...

  • Page 2: History Of Tech 21'S Sansamp

    01-49, and that 00 and 50 are bypass settings. The SansAmp PSA-1 can be used for a variety of applications. In the studio, you can record If you need further guidance in setting up your SansAmp PSA-1, check out the diagrams and direct to tape, enhance existing tracks in mixdowns, as well as add interesting touches to any information on pages 12 through 14.

  • Page 3: Powering The Sansamp Psa-1

    Then, if you want to plug straight into the SansAmp PSA-1, bypassing other parts of the system, you can use the SansAmp PSA-1’s front Input.

  • Page 4: Pre-Amp

    MIDI functions ting, increase the setting in small increments. For increased definition when using distortion, posi- have been activated. Refer to the sections on programming your SansAmp PSA-1 and using tion the knob at its midpoint or towards minimum.

  • Page 5: Save Switch

    P U S H 2 X 0dB position when you plug in extra-hot signals, such as the output from active bass guitars. EVEL SELECTOR SWITCH This switch lets you connect the SansAmp PSA-1 to a wide variety of equipment with a vari- Select a Push...

  • Page 6: Mix 50/50 Switch

    100% wet. Your relative wet/dry mixture can then be controlled by increasing Note: The standard output level range of the SansAmp PSA-1 is 0dB due to the wide avail- or decreasing the effects processor’s output level.

  • Page 7: Using The Sansamp Psa-1'S Inputs

    The front-panel Input jack is designed to accept signals from guitars, basses, keyboards, etc. 50% of the SansAmp PSA-1 signal goes You can set up your SansAmp PSA-1 as a permanent part of a rack or patch-bay setup, with through your effects processor, and the its usual input source plugged into the rear-panel jack.

  • Page 8: Using Midi And Remote Footswitch

    MIDI Thru, except when data is being transmitted from the SansAmp PSA-1. Any momen- Use the Up and Down keys to select any of these functions: tary-action footswitch can be used to cycle through the SansAmp PSA-1's presets, as well as MIDI footcontrollers that include a momentary-action switch.

  • Page 9: Function 2: Midi Mapping

    The display will show two zeroes and blinking dots to indicate that The SansAmp PSA-1 comes from the factory with its MIDI map set by default to map incom- Note: If you select a number above 99, the number 1, for you’re back at function 00.

  • Page 10: Function 3: Set Footswitch Loop Count

    SansAmp PSA-1 is at program 00, or bypass. Once Now, if you program the SansAmp PSA-1 to step through only two presets, you can set up you’ve remapped the programs to your satisfaction, press the Save button to exit the Special rhythm and lead programs for individual songs, and select the grouping with your MIDI foot- Page menu.

  • Page 11: Function 5: Midi Channel Select

    Omni (receive on any or all channels), or specific channels 1 through 16. Push the Save cable from the MIDI Thru/Out jack on the rear of the SansAmp PSA-1 to the MIDI in jack button, and the display shows the current setting. Press the Up or Down buttons to select either on a sequencer, computer, etc.
  • Page 12 M O D E L M O D E L PSA-1 PSA-1 LIST OF PRESETS LIST OF CUSTOM SETTINGS Note: Factory presets are based upon using the appropriate types of instruments and/or (Keep a checklist of your customized programs.) accessories associated with each particular sound. ROGRAM OUND ROGRAM...

  • Page 13: Custom Settings Diagrams

    M O D E L M O D E L PSA-1 PSA-1 CUSTOM SETTINGS DIAGRAMS (Photocopy these pages and keep a record of your customized programs.) Program Number Program Number PRE - AMP BUZZ PUNCH CRUNCH DRIVE HIGH LEVEL PRE - AMP BUZZ PUNCH CRUNCH...

  • Page 14: Global Reset

    If unit becomes defective within warranty period, Tech 21, Inc., will elect to repair or replace it free of charge. After war- ranty period expires, manufacturer will repair defective unit for a fee.

Table of Contents