Ford 1998 Crown Victoria Owner's Manual
  1. Manuals
  2. Brands
  3. Ford Manuals
  4. Automobile
  5. 1998 Crown Victoria
  6. Owner's manual

Ford 1998 Crown Victoria Owner's Manual

Ford motor company 1998 ford crown owner's guide
Hide thumbs
Table of Contents

Advertisement

Quick Links

Before driving
Starting and driving
Servicing
All rights reserved. Reproduction by any means, electronic or mechanical
including photocopying, recording or by any information storage and retrieval
system or translation in whole or part is not permitted without written
authorization from Ford Motor Company.
Copyright
1997 Ford Motor Company
Contents
2
3
23
58
78
83
95
109
145
151
152
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 1998 Crown Victoria and is the answer not in the manual?

Questions and answers

Related Manuals for Ford 1998 Crown Victoria

Summary of Contents for Ford 1998 Crown Victoria

  • Page 1: Table Of Contents

    All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Copyright 1997 Ford Motor Company...

  • Page 2: Introduction

    If possible, you should avoid full use of the brakes for the first 1 600 km (1 000 miles). INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation.

  • Page 3: Instrumentation

    Instrumentation...
  • Page 4 Instrumentation Instrument panel dimmer switch (pg. 23) Headlamp control (pg. 23) PANEL AUTO LAMP PUSH INTERIOR R.DEF. Turn signal and wiper/washer control (pg. 34) Tilt steering wheel lever (pg. 35) *if equipped Instrument cluster (pg. 6) Rear window defroster control (pg.
  • Page 5 Electronic sound system (pg. 33) TREB FADE TAPE DOLBY B NR SCAN SIDE Climate control systems (pg. 25) Passenger side air (pg. 68) Clock (pg. 33) Instrumentation...

  • Page 6: Warning Lights And Chimes

    Instrumentation WARNING LIGHTS AND CHIMES Standard instrument cluster CHECK TRAC CNTL FUEL ENGINE VOLTS FUEL < FUEL FILL DOOR Optional instrument cluster EMPTY Low fuel Illuminates when the fuel tank has approximately eight liters (two gallons) remaining. The lamp will also illuminate when the ignition key is turned to ON and the engine is off.
  • Page 7 Instrumentation Check engine Your vehicle is equipped with a computer that monitors the engine’s CHECK emission control system. This ENGINE system is commonly known as the On Board Diagnostics System (OBD II). This OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards.
  • Page 8 Instrumentation Light is blinking: Engine misfire is occurring which could damage your catalytic converter. You should drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced at the first available opportunity. Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire.
  • Page 9 Instrumentation Anti-lock brake system (ABS) (If equipped) Momentarily illuminates when the ignition is turned on and the engine is off. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the brake warning light also remains illuminated with parking brake released.
  • Page 10 Instrumentation Engine oil pressure (if equipped) Illuminates when the oil pressure falls below the normal range. Stop the vehicle as soon as safely possible and switch off the engine immediately. Check the oil level and add oil if needed. Refer to Engine oil in the Maintenance and Care chapter.
  • Page 11 O/D off Illuminates when the transmission control switch has been pushed. When the light is on, the transmission does not shift into overdrive. If the light does not come on when the transmission control switch is depressed or if the light flashes when you are driving, have your vehicle serviced.

  • Page 12: Fuel Gauge

    Instrumentation Headlamps on warning chime Sounds when the headlamps or parking lamps are on, the ignition is off (and the key is not in the ignition) and either front door is opened. Turn signal chime Sounds when the turn signal lever has been activated to signal a turn. GAUGES Standard instrument cluster gauges TRAC...
  • Page 13 amount of reserve fuel in the tank. When refueling the vehicle from empty indication, the amount of fuel that can be added will be less than the advertised capacity due to the reserve fuel. Standard instrument cluster Optional instrument cluster Speedometer Indicates the current vehicle speed.
  • Page 14 Instrumentation Optional instrument cluster Odometer Registers the total kilometers (miles) of the vehicle. Standard instrument cluster Optional instrument cluster Refer to Electronic Message Center for information on how to switch the display from metric to English measurements. 60 70 0 0 0 0 0 0 0 km/h km/h km/h...
  • Page 15 Trip odometer Registers the kilometers (miles) of individual journeys. To reset, depress the control. Refer to electronic message center for Trip A and Trip B features on the optional instrument cluster. Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H”...
  • Page 16 Instrumentation Optional instrument cluster This gauge indicates the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level or mixture, the gauge indication will not be accurate. Battery voltage gauge (if equipped) This gauge shows the battery voltage when the ignition is in the ON position.
  • Page 17 chapter). If the oil level is correct, have your vehicle checked at your dealership or by a qualified technician. ELECTRONIC MESSAGE CENTER The electronic message center only works when the ignition is in the ON position. The message center allows you to: see problems such as door ajar, air suspension, trunk ajar, washer fluid low...
  • Page 18 Instrumentation Press this control to switch the electronic instrument cluster display and the message center display from metric to English units. Select Each press of the SELECT control will select a different function. Press the right side of the control to advance the function to the right, and press the left side of the control to advance the function to the left.
  • Page 19 Remember to turn the ignition OFF when refueling your vehicle. Otherwise, the display will not show the addition of fuel for a few miles. At least 9.5 liters (2.5 gallons) of fuel must be added for the fuel gauge to immediately show the new fuel level. The DTE function will flash for 5 seconds and sound a tone for 1 second when you have approximately: 80 km (50 miles) left before you run out of fuel...
  • Page 20 Instrumentation Press the RESET control while AVG ECON is displayed to reset the function. The average displayed is the average since the last reset. INST ECON (instantaneous fuel economy) Select this function to calculate the instantaneous fuel economy of your running vehicle.

  • Page 21: Overdrive Off

    AVG SPEED (average speed) Select this function to display your average speed in miles per hour or kilometers per hour. Your vehicle must be moving to calculate your average speed. When your vehicle is not moving, the average speed is displayed at 0 kilometers (0 miles) per hour. Message center indicator lights Check air suspension Briefly illuminates when the ignition...
  • Page 22 Instrumentation Low washer fluid Momentarily illuminates when the ignition is turned to ON and will stay on when the windshield washer fluid is low. Trunk ajar If the trunk is not completely closed, this light comes on when you turn the ignition to ON. With the ignition ON, this light will flash five times and sound a tone for one second, then remain on (if the trunk...

  • Page 23: Panel Dimmer Control

    PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlight and parklamp operation. Push up to brighten. Push down to dim. HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps only.
  • Page 24 Controls and features Autolamp control (if equipped) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. The autolamp system also keeps the lights on for a preselected period of time after the ignition switch is turned to OFF.

  • Page 25: Climate Control System

    Controls and features The defroster turns off automatically after 10 minutes or when the ignition is turned to the OFF position. To manually turn off the defroster before ten minutes have passed, push the control again. CLIMATE CONTROL SYSTEM Manual heating and air conditioning system (if equipped) VENT Fan speed control Controls the volume of air circulated...
  • Page 26 Controls and features Under normal conditions, your vehicle’s climate control system should be left in any position other than MAX A/C or OFF when the vehicle is parked. This allows the vehicle to “breathe” through the outside air inlet duct. MAX A/C-Uses recirculated air to cool the vehicle.
  • Page 27 To prevent humidity buildup inside the vehicle, don’t drive with the climate control system in the OFF position. Don’t put objects under the front seat that will interfere with the airflow to the back seats. Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield).

  • Page 28: Automatic Operation

    Controls and features Turning the EATC on Press AUTOMATIC, any of the override controls or the fan speed control. The EATC will only operate when the ignition is in the ON position. Turning the EATC off Press OFF. The Outside Temperature function will continue to operate until the ignition is turned off.
  • Page 29 Controls and features Temperature selection The display window indicates the ˚ selected temperature, function AUTO (AUTO or one of the override controls) and manual control of fan speed ( ) if automatic fan speed is not desired. To control the temperature, select any temperature between 18°C (65°F) and 29°C (85°F) by pressing the blue (cooler) or red (warmer)
  • Page 30 Controls and features Fan speed ( When AUTOMATIC is pressed, fan speed is adjusted automatically for existing conditions. You can override fan speed at any time. To control fan speed manually, use the thumbwheel to cancel automatic fan speed operation. Rotate the thumbwheel up for higher fan speed or down for lower fan speed.
  • Page 31 Controls and features economical and will cool the inside of the vehicle faster. Airflow is from the instrument panel registers. This mode can also be used to prevent undesirable odors from entering the vehicle. NORM A/C-Uses outside air to cool the vehicle. The temperature display will remain the same and air will be cooled based on the selected temperature.
  • Page 32 Controls and features Displaying outside temperature Press OUTSIDE TEMP to display the outside air temperature. It will be displayed until OUTSIDE TEMP is pressed again. If the selected temperature is changed while the outside temperature is displayed, the new temperature will be displayed for four seconds after it is changed, then the outside temperature will return to the window.

  • Page 33: Audio System

    Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield). If your vehicle has been parked with the windows closed during hot weather, the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open.

  • Page 34: Turn Signal Control

    Controls and features TURN SIGNAL CONTROL Push down to activate the left turn signal. Push up to activate the right turn signal. The flash rate of the turn signal will speed up considerably if the Lighting Control Module detects a left or right turn lamp bulb (front or rear) is burned out.

  • Page 35: Positions Of The Ignition

    Controls and features POSITIONS OF THE IGNITION 1. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. 3. OFF, shuts off the engine and all accessories without locking the steering wheel.
  • Page 36 Controls and features SPEED CONTROL (IF EQUIPPED) To turn speed control on Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved.
  • Page 37 To set a speed Press SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed.
  • Page 38 Controls and features You can accelerate with the accelerator pedal at any time during speed control usage. Releasing the accelerator pedal will return your vehicle to the previously programmed set speed. To set a lower set speed Press and hold CST/COAST. Release the control when the desired speed is reached or Press and release CST/COAST.

  • Page 39: Speed Control

    Pressing OFF will erase the previously programmed set speed. To return to a previously set speed Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). Indicator light This light comes on when either the SET ACC/SET ACCEL or RES/RSM/RESUME controls are pressed.
  • Page 40 Controls and features When programming your HomeLink Universal Transmitter, you will be operating the garage door or gate. Be sure that people and objects are out to the way to prevent potential harm or damage. Do not use the HomeLink Universal Transmitter with any garage door opener that lacks safety stop and reverse features as required by U.S.
  • Page 41 Note to Canadian residents During programming, your hand-held transmitter may automatically stop transmitting after two seconds which may not be long enough to program the HomeLink Universal Transmitter. If you are programming from one of these hand-held transmitters: continue to hold the control on the HomeLink Universal Transmitter re-press the hand-held...

  • Page 42: Automatic Dimming Inside Rear View Mirror (If Equipped)

    Controls and features 2. Press the training control on the garage door opener receiver until the training light (next to the control) begins to flash (1-2 seconds). 3. Press the programmed HomeLink control in the vehicle until the training light on the garage door receiver turns solid (1-2 seconds).

  • Page 43: Electronic Compass (If Equipped)

    Controls and features Press the control to turn the mirror on or off. The mirror will automatically return to the normal state whenever the COMP MIRROR vehicle is placed in R (Reverse)(when the mirror is on) to ensure a bright clear view when backing up.
  • Page 44 Controls and features Compass zone adjustment 1. Determine which compass zone you are in by referring to the zone map. 2. With the compass display turned on, press and hold the COMP side of the control until the zone selection number appears in the mirror display window.

  • Page 45: Power Windows

    Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines. 1. Start the vehicle. 2. Press and hold the COMP side of the control for approximately six seconds until “C” appears in the mirror display.
  • Page 46 Controls and features Press the bottom portion of the rocker switch to open. Express down Press AUTO and release quickly. The window will open fully. Depress again to stop window operation. Window lock The window lock feature allows only the driver to operate the power windows.

  • Page 47: Power Door Locks - If Equipped

    POWER DOOR LOCKS (IF EQUIPPED) Press U to unlock all doors and L to lock all doors. POWER SIDE VIEW MIRRORS The ignition must be in ACC or ON position to adjust the power side view mirrors. To adjust your mirrors: 1.

  • Page 48: Remote Entry System (If Equipped)

    Controls and features CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door.
  • Page 49 Controls and features Unlocking the doors Press this control to unlock the driver’s door. The interior lamps will illuminate. Press the control a second time within five seconds to unlock all doors. Locking the doors Press this control to lock all doors. The horn will chirp and the parklamps/taillamps will flash to confirm the control was pressed.
  • Page 50 Controls and features Autolock This feature automatically locks all doors when: all vehicle doors are closed the ignition is in the ON position you shift into or through R (Reverse) the brake pedal is released. Relock The autolock feature repeats when: any door is opened and closed the brake pedal is released.
  • Page 51 Controls and features Opening the trunk Press the control once to open the trunk. Ensure that the trunk is closed and latched before driving your vehicle. Failure to latch the trunk may cause objects to fall out of the trunk or block the rear view.
  • Page 52 Controls and features The inside lights will not turn off if: they have been turned on with the dimmer control or any door is open. The battery saver will shut off the interior lamps 30 minutes after the last door is closed or after 10 minutes if the door is left open. Replacing the battery The transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent.
  • Page 53 Replacing lost transmitters Take all your vehicle’s transmitters to your dealer for reprogramming if: a transmitter is lost or you want to purchase additional transmitters (up to four may be programmed). SECURILOCK ANTI-THEFT SYSTEM The SecuriLock anti-theft system provides an advanced level of vehicle theft protection.
  • Page 54 Controls and features Theft indicator The theft indicator on top of the instrument panel will operate as follows: When the ignition is OFF, the theft indicator will flash briefly every 2 seconds to indicate the SecuriLock vehicle. When the ignition is turned to RUN or START, the theft indicator will light for 3 seconds and then go out.

  • Page 55: Keyless Entry System

    3. Within five seconds of turning the ignition to OFF, insert the second previously programmed SecuriLock ignition from OFF to RUN (maintain ignition in RUN for at least one second but no more than 5 seconds). 4. Turn the ignition to OFF and remove the second SecuriLock from the ignition.
  • Page 56 Controls and features The factory-set code is located: on the owner’s wallet card in the glove compartment taped to the computer module When pressing the controls on the keyless entry keypad, press the middle of the controls to ensure a good activation. Programming your own entry code 1.
  • Page 57 Unlocking the doors and releasing the trunk with the keyless entry system To unlock the driver door, enter either the factory-set code or personal code (each digit pressed within 5 seconds of prior digit). The interior lamps will illuminate. To unlock all doors, enter the factory-set code or personal code (driver door unlocks) and press 3/4 within 5 seconds.

  • Page 58: Seating And Safety Restraints

    Seating and safety restraints SEATING Head restraints Push or pull the head rests to the desired position. Front seats Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.
  • Page 59 Pull lever up to adjust seatback. Using the manual recline function (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
  • Page 60 Seating and safety restraints Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Press the control to recline the seatback forward or backward (if equipped).
  • Page 61 Press to move the rear portion of the seat cushion up or down. Adjusting the power seats – seat mounted controls Never adjust the driver’s seat or seatback when the vehicle is moving. The power seat controls are located on the side of the driver’s seat. Press to raise or lower the seat, or to move the seat forward or backward.
  • Page 62 Seating and safety restraints To prevent the risk of injury, make sure children sit where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision.
  • Page 63 2. To unfasten, push the release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front and rear seat passenger outboard safety belts have two types of locking modes described below: Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in...
  • Page 64 Seating and safety restraints How to use the automatic locking mode Buckle the combination lap and shoulder belt. Grasp the shoulder portion and pull downward until the entire belt is extracted. Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
  • Page 65 Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, push the button and slide the height control down.
  • Page 66 Seating and safety restraints Insert the tongue into the correct buckle. To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. To tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips.
  • Page 67 (slide bar)(if equipped), shoulder belt height adjusters (if equipped), child safety seat tether bracket assemblies (if equipped), and attaching hardware, should be inspected after a collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced.

  • Page 68: Air Bag Supplemental Restraint System (Srs)

    Seating and safety restraints AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) SUSP 60 70 CHECK ENGINE PANEL VOLTS FUEL AUTO LAMP km/h P R N D 2 1 < FUEL FILL DOOR PUSH INTERIOR R.DEF. Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and...
  • Page 69 Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. Children and air bags...
  • Page 70 Seating and safety restraints How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the...
  • Page 71 Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag is inflated, the air bag will not function again and must be replaced immediately . If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.

  • Page 72: Safety Restraints For Children

    Seating and safety restraints Disposal of air bags and air bag equipped vehicles For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician. Air bags MUST BE disposed of by qualified personnel. SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children.

  • Page 73: Safety Seats For Children

    To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards. Belt-positioning booster seats raise the child and provide a shorter, firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child.
  • Page 74 Put the safety belt in the automatic locking mode. Refer to Automatic locking mode. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
  • Page 75 Seating and safety restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions.
  • Page 76 Seating and safety restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
  • Page 77 Tether anchorage hardware kits (part number 613D74) including instructions, may be obtained at no charge from any Ford or Lincoln-Mercury dealer. All vehicles built for sale in Canada include a tether anchor hardware kit.

  • Page 78: Starting

    Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
  • Page 79 Starting 2. Make sure the headlamps and vehicle accessories are off. 3. Make sure the parking brake is set. 4. Make sure the gearshift is in P (Park). 5. Turn the key to 4 (ON) without turning the key to 5 (START).
  • Page 80 Starting TRAC CHECK CNTL FUEL ENGINE VOLTS FUEL < FUEL FILL DOOR EMPTY Make sure the corresponding lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced. If the driver’s safety belt is fastened, the light ( SUSP 60 70 0 0 0 0 0 0 0...

  • Page 81: Starting The Engine

    STARTING THE ENGINE 1. Turn the key to 5 (START) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to 4 (ON). 2. If the temperature is above 12° C (10° F) and the engine does not start within five seconds on the first try, turn the key to OFF, wait ten seconds and try again.
  • Page 82 Starting Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately. Do not drive if you smell exhaust fumes.

  • Page 83: Driving

    Driving BRAKES Your brakes are self-adjusting. Refer to the “Service Guide” for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
  • Page 84 Driving ABS warning lamp warning lamp in the instrument cluster illuminates for about five seconds when starting the vehicle. If an ABS fault is detected, the light will remain on, the ABS system is disabled with normal braking still effective, and your vehicle should be serviced as soon as possible. Normal braking is still effective unless the BRAKE warning lamp is also illuminated.

  • Page 85: Traction Control

    Driving The parking brake is not designed to stop a moving vehicle. However, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency. Since the parking brake applies only the rear brakes, the vehicle’s stopping distance will increase greatly and the handling of your vehicle will be adversely affected.
  • Page 86 Driving The Traction Control of available traction on slippery surfaces. The system is a driver aid which makes your vehicle easier to handle primarily on snow and ice covered roads. During Traction Control of sound coming from the engine compartment and the engine will not “rev-up”...

  • Page 87: Speed Sensitive Steering

    Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running. This action could damage the power steering pump. Speed sensitive steering The steering in your vehicle is speed sensitive. At high speeds, steering assist will decrease to improve steering feel.

  • Page 88: Transmission Operation

    Driving TRANSMISSION OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift from being moved from P (Park) unless the brake pedal is depressed. If you cannot move the gearshift out of P (Park) with the brake pedal depressed: 1.
  • Page 89 Hold the brake pedal down while you move the gearshift lever from position to position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure someone. P (Park) Always come to a complete stop before shifting into P (Park).
  • Page 90 Driving Overdrive can be deactivated by pressing the transmission control switch on the gearshift lever. The transmission control indicator light (TCIL) will illuminate on the instrument cluster. Drive Not shown on the display. Activate by pressing the transmission control switch on the gearshift lever with the gearshift in the Drive position. The O/D OFF indicator will illuminate in the instrument cluster.

  • Page 91: Vehicle Loading

    Your vehicle is classified as a light duty towing vehicle. It does not come from the factory fully equipped to tow. No towing packages are available through Ford or Mercury/Lincoln dealers. Do not tow a trailer until your vehicle has been driven at least 3 200 km (2 000 miles).
  • Page 92 Driving The amount of weight your loaded trailer should be no more than 907 kg (2 000 lbs.). Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label. Towing trailers beyond the maximum recommended gross trailer weight could result in engine damage, transmission/axle damage, structural damage, loss of control, and personal injury.
  • Page 93 Trailer lamps Trailer lamps are required on most towed vehicles. Make sure your trailer lamps conform to local and Federal regulations. See your dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps. Driving while you tow Do not drive faster than 88 km/h (55 mph) when towing a trailer.

  • Page 94: Driving Through Water

    Driving Launching or retrieving a boat When backing down a ramp during boat launching or retrieval, Do not allow the static water level to rise above the bottom edge of the rear bumper and Do not allow waves to break higher than 15 cm (six inches) above the bottom edge of the rear bumper.

  • Page 95: Fuel Pump Shut-Off Switch

    HAZARD LIGHTS CONTROL Use only in an emergency to warn traffic of vehicle breakdown, approaching danger, etc. The hazard flashers can be operated when the ignition is off. The hazard lights control is located on top of the steering column. Depress hazard lights control to activate all hazard flashers simultaneously.

  • Page 96: Fuses And Relays

    Roadside emergencies The fuel pump shut-off switch is located on the left side of the trunk behind the trunk liner. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse.
  • Page 97 Standard fuse amperage rating and color Fuse rating 5 amp 7.5 amp 10 amp 15 amp 20 amp 20 amp fuse link 25 amp 30 amp 30 amp fuse link 40 amp fuse link 50 amp fuse link 60 amp fuse link 80 amp fuse link 100 amp fuse link Passenger compartment fuse panel...
  • Page 98 Roadside emergencies The fuses are coded as follows. Fuse/Relay Fuse Amp Location Rating Brake Pedal Position (BPP) Switch, Multi-Function Switch, Speed Control Wiper Control Module, Windshield Wiper Motor — Not Used Lighting Control Module, Main Light Switch Backup Lamps, Variable Assist Power Steering (VAPS), Turn Signals, Air Suspension, Daytime Running Lamps, Electronic Day/Night Mirror, Shift Lock,...
  • Page 99 Fuse/Relay Fuse Amp Location Rating 18A CB 20A CB Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses.
  • Page 100 Roadside emergencies The high-current fuses are coded as follows. Fuse/Relay Fuse Amp Location Rating 20A* 30A* 25A* 30A* 15A* 20A* 20A CB 30A** 50A** Description Electric Fuel Pump Relay Generator, Starter Relay, Fuses 15 and 18 Radio, CD Changer, Subwoofer Amplifier Police Power Relay Horn Relay DRL Module...

  • Page 101: Changing The Tires

    Fuse/Relay Fuse Amp Location Rating 50A** 40A** 30A** 50A** 40A** 50A** 50A** 30A** Relay 1 Relay 2 Relay 3 Relay 4 * Mini Fuses ** Maxi Fuses Relays Relays are located in the power distribution box and should be replaced by qualified technicians.
  • Page 102 (not the dealer) to get a replacement key. If the lug wrench/lug nut key assembly is lost, see your nearest Ford or Lincoln/Mercury dealer who has access to the master set of keys. Do not use an impact wrench with the anti-theft key.
  • Page 103 Reinstalling the anti-theft lug nut 1. Insert the key over the locking lug nut. 2. Place the lug nut wrench over the lug nut key and apply pressure on the key with the wrench. 3. Install the lug nut. Tire change procedure To prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to...
  • Page 104 Roadside emergencies On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Refer to Air suspension system in the Driving chapter for more information. 6. Put the jack in the jack notch next to the door closest to the tire you are changing.

  • Page 105: Jump Starting Your Vehicle

    JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. You could damage the catalytic converter. Batteries contain sulfuric acid which burns skin, eyes, and clothing.
  • Page 106 Roadside emergencies Connecting the jumper cables 1. Position the vehicles so that they do not touch one another. 2. Switch off the engine. Switch off any unnecessary electrical equipment. 3. Connect the positive (+) terminal of the discharged battery (1) to the positive (+) terminal of the booster battery (2).
  • Page 107 Removing the jumper cables 1. Remove the jumper cables in reverse order. Take the cable off the metallic engine surface (1) first, followed by the cable on the negative (-) booster battery terminal (2). 2. Remove the cable from the positive (+) terminal of the booster battery (3) and then the discharged battery (4).

  • Page 108: Wrecker Towing

    OFF position (if equipped). When calling for a tow truck, tell the operator what kind of vehicle you have. A towing manual is available from Ford Motor Company for all authorized tow truck operators. Have your tow truck driver refer to this...

  • Page 109: Maintenance And Care

    SERVICE RECOMMENDATIONS To help you service your vehicle: We highlight do-it-yourself items in the engine compartment for easy location. We provide a “Service Guide” which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service.

  • Page 110: Opening The Hood

    Maintenance and care Working with the engine on 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Block the wheels to prevent the vehicle from moving unexpectedly. Do not start your engine with the air cleaner removed and do not remove it while the engine is running.

  • Page 111: Identifying Components In The Engine Compartment

    Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L SOHC V8 engine 1. Brake fluid reservoir 2. Engine oil dipstick 3. Engine oil filler cap 4. Windshield washer fluid reservoir 5. Air filter assembly 6. Power steering fluid reservoir 7.

  • Page 112: Engine Oil

    Maintenance and care ENGINE OIL Checking the engine oil Refer to the Service Guide for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan.
  • Page 113 3. Recheck the engine oil level. Make sure the oil level is not above the MAX mark on the dipstick. Engine oil and filter recommendations Look for this certification mark. Ford oil specification is WSS-M2C153-G. Use SAE 5W-30 motor oil certified for gasoline engines by the American Petroleum Institute. Maintenance and care...
  • Page 114 Change your engine oil and filter according to the appropriate schedule listed in the “Service Guide”. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, startup engine noises or knock may be experienced.
  • Page 115 3. If necessary, add brake fluid until the level reaches MAX. Do not fill above this line. 4. Use only a DOT 3 brake fluid certified to meet Ford specifications. Refer to Lubricant specifications in the Capacities and specifications chapter. Brake fluid is toxic.

  • Page 116: Engine Coolant

    Maintenance and care ENGINE COOLANT Check the level of the engine coolant in the reservoir. Refer to the “Service Guide” for service interval schedules. Be sure to read and understandPrecautions when servicing your vehicle in this chapter. If the engine coolant has not been checked at the above recommended interval, the engine coolant reservoir may become empty.
  • Page 117 Before adding engine coolant, check the color of the coolant in your vehicle. For vehicles with green coolant, use Ford Premium Cooling System Fluid E2FZ-19549–AA (in Canada, Motorcraft CXC-8–B) or an equivalent premium engine coolant that meets Ford specification ESE-M97B44–A.
  • Page 118 Maintenance and care For vehicles with green coolant, not all coolant recycling processes produce coolant which meets Ford specification ESE-M97B44–A, and use of such coolant may harm engine and cooling system components. For vehicles with orange coolant, no recycling process has been approved at this time and use of such coolant may harm engine and cooling system components.
  • Page 119 How fail-safe cooling works Standard cluster Optional cluster If the engine overheats, the engine will automatically switch to alternating cylinder operation. Each disabled cylinder acts as an air pump and cools the engine. When this occurs: if your vehicle is equipped with analog gauges, the engine coolant temperature gauge will move to the H (hot) area if your vehicle is equipped with digital gauges, the engine coolant temperature gauge will illuminate all eight bars and a tone will sound...
  • Page 120 Maintenance and care symbol will begin to flash. if your vehicle is equipped with digital gauges, the gauge bars will flash and a tone will sound continuously for thirty seconds. the engine will completely shut down, causing steering and braking effort to increase.

  • Page 121: Checking And Adding Power Steering Fluid

    Maintenance and care CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the “Service Guide” for the service interval schedules. If adding fluid is necessary, use only MERCON ATF. 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C).

  • Page 122: Transmission Fluid

    Maintenance and care TRANSMISSION FLUID Checking and adding automatic transmission fluid Follow the scheduled service intervals outlined in the “Service Guide.” Before adding any fluid, make sure the correct type is used. The type of fluid used is normally indicated on the dipstick and/or dipstick handle and also in the Lubricant specifications section in the Capacities and specifications chapter.
  • Page 123 Maintenance and care If your vehicle has been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow the fluid to cool before checking.
  • Page 124 Maintenance and care BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the “Service Guide” for the service interval schedules.
  • Page 125 When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.

  • Page 126: Windshield Wiper Blades

    Maintenance and care Always dispose of automotive batteries in a responsible manner. Follow your local standards for disposal. Call your local recycling center to find out more about recycling automotive batteries. WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem less effective.
  • Page 127 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear...
  • Page 128 Maintenance and care Temperature A B C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
  • Page 129 Maintenance and care Four tire rotation (for vehicles with aluminum wheels) Five tire rotation (for vehicles with steel wheels and full size spare tires)

  • Page 130: Snow Tires And Chains

    Maintenance and care Replacing the tires Replace the tires when the wear band is visible through the tire treads. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier to lose control and roll over.

  • Page 131: What You Should Know About Automotive Fuels

    Remove the tire chains when they are no longer needed. Do not use tire chains on dry roads. The suspension insulation and bumpers will help prevent vehicle damage. Do not remove these components from your vehicle when using snow tires and chains. WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank.
  • Page 132 Maintenance and care Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury. Avoid getting fuel liquid in your eyes.
  • Page 133 It should not be necessary to add any aftermarket products to your fuel tank if you continue to use a high-quality fuel. Cleaner air Ford approves the use of gasolines to improve air quality, including reformulated gasolines that contain oxygenates up to 10% ethanol or 15% MTBE.

  • Page 134: Emission Control System

    Maintenance and care Running out of fuel Avoid running out fuel because this situation may have an adverse affect on powertrain components. If you have run out of fuel: You may need to crank the engine several times before the system starts to pump fuel from the tank to the engine.
  • Page 135 If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.

  • Page 136: Exterior Bulbs

    Maintenance and care If the vehicle’s powertrain system or its battery has just been serviced, the OBD-II system is reset to a “not ready for I/M test” condition. To ready the OBD-II system for I/M testing, a minimum of 30 minutes of city and highway driving is necessary as described below: First, at least 10 minutes of driving on an expressway or highway.
  • Page 137 Maintenance and care 2. Remove the protective cover by turning the three knobs to the unlock position. 3. Disengage the safety snap on the connector by pulling upward slightly on the clip. 4. Release clip and disconnect the electrical connector from the bulb. 5.

  • Page 138: Aiming The Headlamps

    Maintenance and care Replacing front parking lamp/turn signal bulbs 1. Make sure headlamp switch is in OFF position, then open the hood. 2. Remove the protective cover by turning the three knobs to the unlock position. 3. Disengage the safety snap on the connector by pulling upward slightly on the clip.

  • Page 139: Replacing The Interior Bulbs

    The headlamps do not seem to provide enough light for clear night vision. The headlamp beams are pointed substantially away from a slightly down and to the right position. REPLACING THE INTERIOR BULBS Check the operation of the following interior bulbs frequently: interior overhead lamp map lamp Using the right bulbs...

  • Page 140: Cleaning And Caring For Your Vehicle

    Cleaning the wiper blades and windshield. Repairing paint chips Minor scratches or paint damage from road debris may be repaired with touch-up paint, repair foil or aerosol paint spray from the Ford accessory line. Observe the application instructions on the products.
  • Page 141 Remove particles such as bird droppings, tree sap, insect remains, tar spots, road salt and industrial fallout immediately. Cleaning the wheels Wash with the same detergent as the body of your vehicle. Do not use acid-based or alcohol-based wheel cleaners, steel wool, fuel or strong detergents.
  • Page 142 Maintenance and care Cover the highlighted areas to prevent water damage when cleaning the engine. Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary.
  • Page 143 Cleaning the instrument panel Clean with a damp cloth, then dry with a dry cloth. Avoid cleaner or polish that increases the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection.
  • Page 144 Maintenance and care of the area at a time. For heavily soiled areas, spray the cleaner directly onto the leather (two squirts should be adequate) and rub with the pad. Repeat if necessary. Use a soft, damp cloth to remove the loosened dirt and foam. Dry with a soft cloth.

  • Page 145: Capacities And Specifications

    MOTORCRAFT PART NUMBERS Component Air filter Fuel filter Battery (standard) Battery (optional) Oil filter PCV valve Spark plugs* * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information. If a spark plug is removed for inspection, it must be reinstalled in the same cylinder.

  • Page 146: Refill Capacities

    If your engine coolant is green in color, use Ford Premium Cooling System Fluid. If your coolant is orange in color, use Ford Extended Life Engine Coolant. Refer to Lubricant Specifications. Add 118 ml (4 oz.) of additive friction modifier C8AZ-19B546–A, Ford specification EST-M2C118–A for complete refill of Traction-Lok axles.

  • Page 147: Lubricant Specifications

    LUBRICANT SPECIFICATIONS Item Ford part name Brake fluid High Performance DOT 3 Motor Vehicle Brake Fluid Door Silicone Lubricant weatherstrips Engine Ford Premium coolant Engine Coolant (green in color) Ford Extended Life Engine Coolant (orange in color) Engine oil Motorcraft 5W30...

  • Page 148: Engine Data

    Premium Rear Axle Lubricant Windshield Ultra-Clear washer fluid Windshield Washer Concentrate Add 118 ml (4 oz.) of additive friction modifier C8AZ-19B546–A, Ford specification EST-M2C118–A for complete refill of Traction-Lok axles. ENGINE DATA Engine Cubic inches Horsepower-single exhaust Horsepower-dual exhaust Torque-single exhaust...
  • Page 149 Capacities and specifications...

  • Page 150: Vehicle Identification Number

    The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmission, frame and transfer case (if equipped). MFD. BY FORD MOTOR CO. IN U.S.A. DATE: XXXXX GVWR:XXXXX LB/ XXXXX KG FGAWR: XXXXXX/XXXXXXX...

  • Page 151: Reporting Safety Defects

    However, NHTSA cannot become involved in individual problems between you, your dealer or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1–800–424–9393 (202–366–0123 in the Washington D.C.

  • Page 152: Index

    Index Aiming headlamps ...138 Air bag supplemental restraint system ...68 and child safety seats ...69 description ...68 disposal ...72 indicator light ...71 passenger air bag ...70 Air conditioning manual heating and air conditioning system ...25,26 Air suspension description ...87 Anti-lock brake system (ABS)description Battery ...124 voltage gauge ...16...
  • Page 153 Hazard flashers ...95 Headlamps ...23 autolamp system ...24 daytime running lights ...24 flashing ...23 high beam ...23 Heating ...25 High beams indicator light ...9 Hood release lever ...110 Ignition positions of the ignition ...35 Instrument panel cleaning ...143 lighting up panel and interior .23 Keyless entry system autolock ...50 keypad ...55...
  • Page 154 Index cleaning upholstery ...143 head restraints ...58 lumbar support ...61 Servicing your vehicle ...109 precautions when servicing ...109 Speed control ...36 canceling a set speed ...38 indicator light ...39 resuming a set speed ...39 tap up/tap down ...37,38 turning off ...36 Speed sensitive steering ...87 Speedometer ...13 Starting your vehicle ...78,81...

  • Page 160: Filling Station Information

    Coolant capacity Power steering fluid capacity If your engine coolant is green in color, use Ford Premium Cooling System Fluid. If your engine coolant is orange in color, use Ford Extended Life Engine Coolant. Refer to Lubricant Specifications. Ensure correct automatic transmission fluid is used for a specific application.

This manual is also suitable for:

Crown vic 1993

Table of Contents

Save PDF