JUKI IP-420 Instruction Manual
  1. Manuals
  2. Brands
  3. JUKI Manuals
  4. Sewing Machine Accessories
  5. IP-420
  6. Instruction manual

JUKI IP-420 Instruction Manual

Input
Hide thumbs Also See for IP-420:
Table of Contents

Advertisement

Quick Links

ENGLISH
IP-420
INPUT INSTRUCTION MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IP-420 and is the answer not in the manual?

Questions and answers

Related Manuals for JUKI IP-420

Summary of Contents for JUKI IP-420

  • Page 1 ENGLISH IP-420 INPUT INSTRUCTION MANUAL...

  • Page 2: Table Of Contents

    CONTENTS 1. START AND END OF THE BODY INPUT MODE ..........1 1-1. Move to the body input mode ..................... 1 1-2. Return to the normal sewing mode................... 4 2. BASIC OPERATION AND DISPLAY ..............5 2-1. Common button ........................5 2-2.
  • Page 3 (9) External output (012) ........................47 (10) Enlargement/reducton reference pont (004) ................48 (11) Inverson pont (005) ........................49 (12) Thread tenson settng (014) ......................50 (13) Intermedate presser heght settng (018) ..................51 (14) Area Classification (016) ........................ 52 (15) Sewng machne stop (019) ......................
  • Page 4 7. FORMATTING MEDIA (090) ................90 8. TRIAL SEWING ....................91 8-1. Preparing the trial sewing ....................91 8-2. Performing the trial sewing ....................93 9. SETTING FUNCTION ..................95 9-1. Comment input ........................95 9-2. Clamp inversion setting (091) ..................96 9-3.

  • Page 5: Start And End Of The Body Input Mode

    1. START AND END OF THE BODY INPUT MODE 1-1. Move to the body input mode <Data input screen> 1 Turn ON the power switch. When the power switch is turned ON, the data input screen of the normal sewing mode is displayed after the welcome screen was displayed.
  • Page 6 <Mode screen> 3 Select the body input mode. Press MODE SELECTION button B to change over the display from the normal sewing mode selection state to the body input mode selection state LK-1900A series AMS-E series 4 Move to the body input mode.
  • Page 7 5 Select the sewing data use. When SEWING DATA USE button D is pressed, the body input mode standard screen is displayed in the state that the backup data is used. When ENTER button E is pressed, new creation can be performed. <Standard screen> AMS-E series LK-1900A series AMS-EN series...

  • Page 8: Return To The Normal Sewing Mode

    1-2. Return to the normal sewing mode. 1 Display the mode screen. In order to return from the body nput mode to the normal sewng mode, press MODE button n the 6tandard screen to dsplay the mode screen. 2 Select the normal sewing mode. Press MODE SELECTION button A , and change over the dsplay from body nput mode selecton state...

  • Page 9: Basic Operation And Display

    2. BASIC OPERATION AND DISPLAY Explanaton s gven for the operaton and the dsplay whch are common to the body nput mode. 2-1. Common button Buttons that perform common operaton n the respectve screens of the body nput mode are as shown n the lst below.

  • Page 10: Body Input Mode Standard Screen

    2-2. Body input mode standard screen The standard screen of the body nput mode s as shown below. Buttons of the body nput mode standard screen are as shown n the lst below. Button Name of button Description PATTERN READ button Pattern readng screen s dsplayed.
  • Page 11 Button Name of button Description Comment nput screen s dsplayed. COMMENT INPUT button → See “9-1. Comment input” p.95. CODE LIST button Code lst screen s dsplayed. “2-3. Selection of function” p.10. → See CONTENTS DISPLAY Contents dsplay screen s dsplayed, and detaled nformaton on the present needle poston s dsplayed.
  • Page 12 Button Name of button Description FUNCTION button Functon allocated to the button can be drectly called. (“4-1. (1) Jump feed” p.23). Executes jump feed Executes pont sewng (“4-1. (6) Point sewing” p.31). Executes normal sewng (“4-1. (7) Ordinary sewing” p.32). Executes thread trmmng (“4-5.
  • Page 13 Name of button Description Button PRESENT NEEDLE Part where nformaton on the present needle poston s dsplayed. POSITION Contents of the dsplay s shown below. INFORMATION dsplay Item Description Absolute coordnate Absolute coordnate from the orgn of the present needle poston s dsplayed. Relatve coordnate Relatve coordnate of the present needle poston s dsplayed.

  • Page 14: Selection Of Function

    2-3. Selection of function Procedure of the functon selecton of the body nput mode s gven below. 1 Display the code list screen. When CODE LIST button s pressed n the standard screen of the body nput mode, the code lst screen s dsplayed.

  • Page 15: Input The Numeric Value

    2-4. Input the numeric value Common numerc value nput procedure at the tme of creatng the pattern data s gven below. 1 Input the setting item. The figure on the right-hand side is the screen which is dsplayed when nputtng the set value of settng tem of the functon.

  • Page 16: Specifying The Position

    2-5. Specifying the position The figure on the right-hand side is the position specifying screen whch s dsplayed when specfyng the poston at the settng of functon. The selected functon code s dsplayed at J . 1 Press MOVE key The presser and the present needle poston dsplay M move n the pressed drecton, and the coordnate value dsplay L s updated.
  • Page 17 4 Press CANCEL button The data durng nputtng s destroyed, and the screen returns to the standard screen. By pressng ENTER button at nputtng of the last pont, pressng down of the decdng pont button can be omtted. 5 Press COORDINATE DIRECT INSTRUCTIONS button The coordnate drect nstructons screen (“16-1.

  • Page 18: Example Of Operating Procedure

    3. EXAMPLE OF OPERATING PROCEDURE A seres of operatng procedure up to tral sewng s gven below. For the detals, refer to the respectve tems. 3-1. Pattern input Create the pattern below usng the nput functon. [Input point] Linear line (pitch 3 mm) X(mm) Y(mm) –5.0...
  • Page 19 Move the needle poston up to 1 usng MOVE key C n the jump feed poston specfyng screen, press DECIDING POINT button D , and press ENTER button At this time, the presser moves. So, be careful. 2 Input of the linear ordinary sewing Press CODE LIST button F n the standard screen to dsplay the code lst screen.
  • Page 20 Press MOVE key I n the lnear ordnary sewng poston specfyng screen, move the needle poston from 1 to 2 , and press DECIDING POINT button Repeat ths operaton to nput up to the poston of 5 , and press ENTER button At this time, the presser moves.

  • Page 21: Trial Sewing

    3-2. Trial sewing The shape or the like of the pattern created by using the input function or readout data is confirmed with the tral sewng. Screen and settng possble tem of tral sewng change n accordance wth machne models. Descrpton below s the example regardng AMS-210EN.

  • Page 22: Modification Of The Pattern

    3-3. Modification of the pattern Modfy the pattern data whch has been created n “3-1. Pattern input” p.14. 1 Deletion of element Move the needle poston on the way of the jump feed secton up to 1 usng FEED FORWARD/BACKWARD buttons <Standard screen>...
  • Page 23 3 Deletion of point Move the needle poston up to the poston of E n the standard screen usng FEED FORWARD/BACKWARD buttons Select ABSOLUTE POINT DELETION (functon code 074) from the functon code lst to dsplay the range specfyng screen. In case of deletng plural needle entry ponts, press FEED FORWARD button F to move the needle poston, and...
  • Page 24 5 Move of point Move the needle poston up to the poston of L n the standard screen usng FEE FORWARD/BACKWARD buttons A , and select ABSOLUTE POINT MOVE (functon code 075) Move the needle poston up to the poston M of the movng pont n the poston specfyng screen usng MOVE key N , and press ENTER button The needle entry point moves as shown in the figure below.

  • Page 25: Pattern Writing

    3-4. Pattern writing The created pattern s wrtten to the meda. Use the media which has been formatted with IP-420. 1 Display the pattern writing screen. Press WRITE button n the standard screen to dsplay the pattern wrtng screen. 2 Select the object media selection screen.

  • Page 26: Pattern Reading

    3-5. Pattern reading Pattern data wrtten to the meda s read n. Use the media which has been formatted with IP-420. 1 Display the pattern reading screen. Press READ button to dsplay the pattern readng screen. 2 Display the pattern kind selection screen.

  • Page 27: Input Of Pattern

    4. INPUT OF PATTERN 4-1. Ordinary sewing (1) Jump feed (020) This is used when moving the presser to the specified position without driving the sewing machine. 1 Display the jump feed setting screen. When pressng JUMP FEED button A n the standard screen or selectng and executng JUMP FEED (functon code 020) n the code lst screen, the jump feed settng...
  • Page 28 3 Set the jump feed speed. Drect nput the value wth TEN keys D or ncrease/decrease the value wth + or - button n the jump feed speed nput screen, and set the jump feed speed. When ENTER button F s pressed, the nput value becomes effectve, and the screen returns to the jump feed settng screen.

  • Page 29: LNear OrdNary SewNg (023)

    (2) Linear ordinary sewing (023) When one point is specified, the straight line connecting the point and the needle position is inputted as the specified stitch length. 1 Display the linear ordinary sewing setting screen. Select and execute LINEAR ORDINARY SEWING (functon code 023) n the code lst screen, and the lnear ordnary sewng settng screen s dsplayed.
  • Page 30 3 Move the needle position. Press MOVE key G n the coordnate nput screen, and the needle position moves in the specified direction. While MOVE key s held pressed, the needle poston contnuously moves. 4 Input the coordinate. When the needle position has moved to the specified position and DECIDING POINT button H s pressed, the poston s nputted as the shape pont (passng pont).

  • Page 31: SplNe OrdNary SewNg (024)

    (3) Spline ordinary sewing (024) It s possble to smply nput the smooth curve usng the splne ordnary sewng. 1 Display the spline ordinary sewing setting screen. When selectng and executng SPLINE ORDINARY SEWING (functon code 024) n the code lst screen, the splne ordnary sewng settng screen s dsplayed.
  • Page 32 1. In order to input the smooth shape of spline ordinary sewing, the neat curve can be obtained when selecting the input point following the procedure below. 1) Select the top of input curve as the input point. ( 5 and 9 ) 2) Making the points selected in step 1) the center, select the points which are separated a little before and after the...

  • Page 33: Arc OrdNary SewNg (025)

    (4) Arc ordinary sewing (025) When two points are specified, the arc connecting the points and the needle position is inputted as the specified stitch length. Sewing direction is in the order of the specified points, and either clockwise drecton or counterclockwse one can be nputted. 1 Display the arc ordinary sewing setting screen.

  • Page 34: CRcle OrdNary SewNg (026)

    (5) Circle ordinary sewing (026) When two points are specified, the circle connecting the points and the needle position is inputted as the stitch length. Stitch direction is in the order of the specified points, and either clockwise direction or counterclockwse one can be nputted.

  • Page 35: PoNt SewNg (021)

    (6) Point sewing (021) Ths functon s used when drect nputtng the needle entry pont one sttch by one sttch. 1 Display the point sewing setting screen. Press POINT SEWING button n the standard screen, or select and execute POINT SEWING (functon code 021) n the code lst screen, the pont sewng settng screen s dsplayed.

  • Page 36: OrdNary SewNg (022)

    (7) Ordinary sewing (022) Ths functon can nput the lnear ordnary sewng and the splne ordnary sewng. 1 Display the ordinary sewing setting screen. Press ORDINARY SEWING button n the standard screen, or select and execute ORDINARY SEWING (functon code 022) n the code lst screen, and the ordnary sewng settng screen s dsplayed.

  • Page 37: Zigzag Sewing (030 To 033)

    4-2. Zigzag sewing (030 to 033) Ths functon s the nput functon to create the needle entry pont of zgzag n the lateral drecton n terms of the nput reference lne. It s convenent to perform nputtng of zgzag sewng of wappen or the lke. There are 4 knds of zgzag sewngs below.
  • Page 38 3 Move the needle position. When MOVE key G n the coordnate nput screen is pressed, the needle position moves in the specified drecton. 4 Input the coordinate. When the needle position has moved to the specified position and DECIDING POINT button H s pressed, the poston s nputted as the shape pont (passng pont).

  • Page 39: Offset Sewing (034 To 037)

    4-3. Offset sewing (034 to 037) This is an input function to create the needle entry point which is separated an optional fixed distance n terms of the nput reference lne. It s convenent when nputtng the needle entry pont takng the perphery of small thng as the reference when attachng the small thngs or the lke.
  • Page 40 3 Move the needle position. Press MOVE key G n the coordnate nput screen, and the needle position moves in the specified direction. 4 Input the coordinate. When the needle position has move to the specified position, press DECIDING POINT button H , and the poston s nputted as the shape pont (passng pont).

  • Page 41: Double Sewing

    4-4. Double sewing This is an input function to create the needle entry point to the point which is separated an optional fixed dstance n terms of the nput reference lne. (1) Double orderly sewing (040 to 043) Create the sewing so that the sewing composed with the input points and that of the offset figure are in the same drecton.
  • Page 42 3 Move the needle position. Press MOVE key G n the coordnate screen, and the needle position moves in the specified direction. 4 Input the coordinate. When the needle position has moved to the specified position and DECIDING POINT button H s pressed, the poston s nputted as the shape pont (passng pont).

  • Page 43: Double Reverse SewNg (044 To 047)

    (2) Double reverse sewing (044 to 047) Create the sewing so that the sewing composed at the input point and that of the offset figure are in the reverse drecton. There are 4 knds of the double reverse sewngs below. •...

  • Page 44: Overlapped Reverse SewNg (050 To 053)

    (3) Overlapped reverse sewing (050 to 053) Sewing of the figure composed at the input point and that which returns it reversely are created. There are four dfferent types of overlapped reverse sewng as descrbed below: • Lnear overlapped reverse sewng (functon code 050) •...
  • Page 45 3 Move the needle position. Press MOVE key D n the coordnate nput screen, and the needle position moves in the specified direction. 4 Input the coordinate. When the needle position has moved to the specified position, and DECIDING POINT button E s pressed, the poston s nputted as the shape pont (passng pont).

  • Page 46: Machine Control Command

    4-5. Machine control command Machne control command nputs varous control commands to the present pont. (1) Thread trimming (001) Thread trmmng can be optonally performed on the way of pattern data. 1 Select thread trimming. When selecting and executing THREAD TRIMMING (function code 001) n the code lst screen, the left-hand screen s dsplayed.

  • Page 47: Stop (003)

    (3) Stop (003) Ths functon nputs the Stop command. 1 Select the Stop. When selectng and executng STOP (functon code 003) n the code lst screen, the left-hand screen s dsplayed. 2 Specify the stop state. The presser state at the tme of stop s dsplayed at PRESSER STATE SETTING button B , and the needle poston at the tme of stop s dsplayed at NEEDLE POSITION SETTING button...

  • Page 48: One RevolutOn Of SewNg MachNe (006)

    5 Perform setting of the needle position. When NEEDLE POSITION SETTING button C s pressed, the needle poston settng screen s dsplayed. The needle poston at the tme of stop can be selected from F . The selected button s changed n color. When ENTER button G s pressed, the selected contents are nputted, and the screen returns to the stop screen.

  • Page 49: Mark 1 And Mark 2 (008, 009)

    (5) Mark 1 and mark 2 (008, 009) These functons put marks n the pattern. 1 Select mark 1 and mark 2. When selectng and executng MARK 1 (functon code 008) and MARK 2 (functon code 009) n the code lst screen, the left-hand screen s dsplayed. 2 Input the mark 1.

  • Page 50: Delay (010)

    (7) Delay (010) Ths functon can set the external output tme or the lke. 1 Select the delay. When selectng and executng DELAY (functon code 010) n the code lst screen, the left-hand screen s dsplayed. 2 Input the delay value. When the delay value s set wth TEN key and + or - button B n the left-hand screen, and...

  • Page 51: External Output (012)

    (9) External output (012) Ths functon can send sgnal to the external termnal of the sewng machne man unt. 1 Select the external output. When selectng and executng EXTERNAL OUTPUT (functon code 012) n the code lst screen, the left-hand screen s dsplayed.

  • Page 52: Enlargement/ReductOn Reference PoNt (004)

    (10) Enlargement/reduction reference point (004) Enlargement/reducton reference pont can be nputted at the optonal poston of the created pattern data. When the enlargement/reducton reference pont s not set, takng the orgn as the reference, enlargement/reducton s performed. 1 Select the enlargement/reduction reference point. When selectng and executng ENLARGEMENT/REDUCTION REFERENCE POINT (functon code 004) n the...

  • Page 53: InversOn PoNt (005)

    (11) Inversion point (005) Inverson pont can be nputted only when the nverson state s set to the optonal nverson at clamp (“9-2. Clamp inversion setting” p.96). nverson settng 1 Select the inversion point. When selectng and executng INVERSION POINT (functon code 005) n the code lst screen, the left-hand screen s dsplayed.

  • Page 54: Thread TensOn SettNg (014)

    (12) Thread tension setting (014) The value of the thread tenson s set. Ths value s vald up to the place where there s the next thread tenson settng command. 1 Select the thread tension setting. When selecting and executing THREAD TENSION SETTING (function code 014) n the code lst screen, the left-hand screen s dsplayed.

  • Page 55: IntermedAte Presser HeGht SettNg (018)

    (13) Intermediate presser height setting (018) The ntermedate presser heght s set. Ths value s effectve up to the poston where the next ntermedate presser heght settng command exsts. 1 Select the intermediate presser height setting. When selectng and executng INTERMEDIATE PRESSER HEIGHT SETTING (function code 018) n the code lst screen, the left-hand screen s dsplayed.

  • Page 56: Area Classification (016)

    (14) Area Classification (016) Area Classification command is inputted. 1 Select the area Classification. When selectng and executng AREA CLASSIFICATION (functon code 016) n the code lst screen, the left- hand screen s dsplayed. 2 Input the area Classification. When ENTER button A s pressed n the rght-hand screen, the area Classification command is inputted, and the screen returns to the standard screen.

  • Page 57: SewNg MachNe Stop (019)

    (15) Sewing machine stop (019) Sewng machne stop command s nputted. 1 Select the sewing machine stop. When selecting and executing SEWING MACHINE STOP (functon code 019) n the code lst screen, the left- hand screen s dsplayed. 2 Specify the stop state. Select the needle poston at the tme of stop from among A .

  • Page 58: MachNe Control Command DeletOn (059)

    (16) Machine control command deletion (059) Machne control command of the present poston (2nd orgn, stop, thread trmmng, thread tenson set value, ntermedate presser heght settng, etc.) s deleted. 1 Select the machine control command deletion. When selecting and executing MACHINE CONTROL COMMAND DELETION (functon code 059) n the code lst screen, the left-hand screen s dsplayed.

  • Page 59: Automatic Back-Tack (064)

    4-6. Automatic back-tack (064) Back-tack of Z type or V type of the specified number of stitches is created to the start of sewing, the end of sewng, or the both of the element ncludng the present pont. 1 Select the automatic back-tack. When selectng and executng AUTOMATIC BACK-TACK (functon code 064) n the code lst screen, the...

  • Page 60: Condensation Sewing (065)

    4-7. Condensation sewing (065) The specified number of stitches of the start of sewing, the end of sewing, or the both of the element including the present point is changed to the specified pitch. 1 Select the condensation sewing. When selectng and executng CONDENSATION SEWING (functon code 065) n the code lst screen, the condensaton sewng settng screen s dsplayed.

  • Page 61: Overlapped Sewing (066)

    4-8. Overlapped sewing (066) Overlapped sewing data of the specified number of stitches is created after the present point. 1 Select the overlapped sewing. When selectng and executng OVERLAPPED SEWING (functon code 066) n the code lst screen, the overlapped sewng settng screen s dsplayed. 2 Perform setting of the overlapped sewing.

  • Page 62: Breakpoint (Spline And Ordinary Sewing)

    4-9. Breakpoint (spline and ordinary sewing) The breakpont s the pont where two ponts of the shape pont of splne sewng are overlapped, and shows the termnaton of one splne curve. The pont where ENTER button C and DECIDING POINT button B are pressed wth the nput of splne sewng becomes the breakpont.
  • Page 63 2 Input the breakpoint in the ordinary sewing. For the ordnary sewng, the pont to be nputted s determned accordng to the knd of element mmedately before the pont where DECIDING POINT button B s pressed. Select ORDINARY SEWING (functon 022) , and nput ponts 1 , 2 , 5 and 7 wth DECIDING POINT button B and ponts 3 , 4 and 6 wth PASSING POINT button...
  • Page 64 When you desre to move pont R to pont S , the result wll be changed by selectng ether shape pont of rear 2 or front 3 . The result when pont of rear 2 has been moved. The result when pont of front 3 has been moved. Pont R can be moved by movng both pont of rear 2 and pont of front 3 to the same coordnates.

  • Page 65: Modification Of The Pattern

    5. MODIFICATION OF THE PATTERN To perform the modification of the pattern, move the needle position to the modifying position using beforehand FEED BACKWARD key or FEED FORWARD key n the standard screen. 5-1. Point modification (1) Point deletion (070 and 074) The pattern data of the specified section is deleted in needle entry point unit.
  • Page 66 4 Execute the relative point deletion. When ENTER button E s pressed n the pont deleton confirmation screen, the point deletion is executed, and the screen returns to the standard screen. In case of the relatve pont deleton, the whole pattern data after the deleted pont moves whle holdng the relaton before deleton.

  • Page 67: PoNt Move (071 And 075)

    (2) Point move (071 and 075) This function moves the specified needle entry point. There are two methods of RELATIVE POINT MOVE and ABSOLUTE POINT MOVE dependng on movng of the pattern data after the moved pont. The pont move can move not only the pattern data created wth the pont sewng nput, but also the data nputted wth any functon such as lnear sewng or the lke.
  • Page 68 In case of the relatve pont move, the whole pattern data after the moved pont moves whle holdng the prevous relaton. Move Relative point move In case of the absolute pont move, select and execute ABSOLUTE POINT MOVE (functon code 075) n the code lst screen.

  • Page 69: PoNt AddNg (076)

    (3) Point adding (076) The point is added after the specified needle entry point. The pattern data after the added pont does not move. Pont addng can be added to not only the pattern data created wth the nput of pont sewng, but also the data nputted wth any functon such as lnear sewng or the lke.
  • Page 70 4 Execute the absolute point adding. When ENTER button D s pressed n the absolute pont adding confirmation screen, point adding is executed and the screen returns to the standard screen. 1. As the result of adding the point, be careful that the distance of change does not exceed the maximum stitch length of the sewing machine.

  • Page 71: Vertex Modification

    5-2. Vertex modification (1) Vertex deletion (072 and 077) This function deletes one specified vertex of the pattern data. There are two methods of RELATIVE VERTEX DELETION and ABSOLUTE VERTEX DELETION dependng on movng of the pattern data after the deleted pont. This function cannot be executed when the specified point is the needle entry point other than the vertex of the element.

  • Page 72: Vertex Move (073 And 078)

    (2) Vertex move (073 and 078) This function moves the specified needle entry point. There are two methods of RELATIVE VERTEX MOVE and ABSOLUTE VERTEX MOVE dependng on movng of the pattern data In case of the relative vertex move : This function cannot be executed when the specified point the needle entry pont other than the vertex.

  • Page 73: Element Deletion (063)

    5-3. Element deletion (063) Ths functon deletes sewng element and machne command n terms of element. All elements after deleton move so as to advance as many as the deleted elements. 1 Display the element deletion executing screen. When pressng ELEMENT DELETION button A n the standard screen, or selectng and executng ELEMENT DELETION (functon code 063)

  • Page 74: Jump Feed Speed Change (060)

    5-4. Jump feed speed change (060) Jump feed speed can be changed to the created jump feed element n terms of element. 1 Display the jump feed speed change setting screen. When selecting and executing JUMP FEED SPEED CHANGE (functon code 060) n the code lst screen, the jump feed speed change settng screen s dsplayed.

  • Page 75: Sewing Speed Section Change (061)

    5-5. Sewing speed section change (061) Sewng speed can be lmted to the created element n terms of needle entry pont. 1 Display the sewing speed section change setting screen. Press SEWING SPEED SECTION CHANGE button the standard screen or select and execute SEWING SPEED SECTION CHANGE (function code 061) n the code lst screen, the sewng speed secton change settng screen s...

  • Page 76: Sewing Pitch Change (062)

    5-6. Sewing pitch change (062) Sewing pitch between the specified elements can be changed to the created element. 1 Display the sewing pitch change setting screen. When selecting and executing SEWING PITCH CHANGE (functon code 062) n the code lst screen, the sewng ptch change settng screen s dsplayed.

  • Page 77: Symmetry

    5-7. Symmetry A figure which is symmetrical to the created pattern is created. Taking the present needle position as the reference, ths functon s performed to the whole pattern. When executng ths functon, set the present needle poston to the poston of the reference beforehand. (1) X-axis symmetry (082) A figure which is symmetrical to X-axis passing the present needle position is created.

  • Page 78: PoNt Symmetry (084)

    (3) Point symmetry (084) Taking the present needle position as reference, a symmetrical figure is created. The present pattern is kept as t s, and the symmetrcal pattern s added after t. 1 Execute the point symmetry. When selectng and executng POINT SYMMETRY (functon code 084) n the code lst screen, and pressng ENTER button in the confirmation screen, the point symmetry is...

  • Page 79: Shape Point Modification

    5-8. Shape point modification Modification of the shape point of element including the present point is performed. (1) Shape point adding (135) Addng of the shape pont s performed. 1 Select the shape point adding. When selecting and executing SHAPE POINT ADDING (functon code 135) n the code lst screen, the presser move confirmation screen is displayed.
  • Page 80 3 Specify the adding position. Usng MOVE key E , specfy the poston of addng destnaton of shape pont wth CURSOR J , and press ENTER button 4 Delete the machine control command. As the machine control command deletion confirmation screen s dsplayed, press ENTER button G f the machne control command on the way of element may be deleted.

  • Page 81: Shape PoNt Move (136)

    (2) Shape point move (136) Move of the shape pont s performed. 1 Select the shape point move. Select and execute SHAPE POINT MOVE (function code 136) s the code lst screen. Operatng procedure of the shape pont move s the same as “5-8.(1) Shape point adding”...

  • Page 82: Shape PoNt DeletOn (137)

    (3) Shape point deletion (137) Deleton of the shape pont s performed. 1 Select the shape point deletion. When selecting and executing SHAPE POINT DELETION (functon code 137) n the code lst screen, the presser move confirmation screen is displayed. When ENTER button A s pressed, the presser moves, and the shape pont specfyng screen s dsplayed.
  • Page 83 3 Delete the machine control command. As the machine control command deletion confirmation screen s dsplayed, press ENTER button E f the machne control command on the way of element may be deleted. 4 Execute the shape point deletion. When ENTER button F s pressed n the shape pont deletion confirmation screen, the shape point deletion is executed, and the screen returns to the standard screen.

  • Page 84: Pattern Operation

    6. PATTERN OPERATION 6-1. Pattern copy (086) Copy of the created pattern s performed up to the maxmum 10 copes. 1 Select the pattern copy. When selectng and executng PATTERN COPY (functon code 086) n the code lst screen, the pattern copy poston specfyng screen s dsplayed.

  • Page 85: Pattern Move (085)

    6-2. Pattern move (085) Parallel move of the created pattern is performed. Positioning can be performed with ease by moving the present position to the position where you desire to move. 1 Move to the reference position. Move the pattern up to the reference position where you desire to move the present point with FEED FORWARD button or FEED BACKWARD button in the standard screen.

  • Page 86: Pattern Erase (087)

    6-3. Pattern erase (087) All created pattern data are erased. 1 Select the pattern erase. When selectng and executng PATTERN ERASE (functon code 087) n the code lst screen, the pattern erase confirmation screen is displayed. 2 Execute the pattern erase. When ENTER button A s pressed, the pattern erase s executed, and the screen returns to the standard screen.

  • Page 87: Pattern Reading

    6-4. Pattern reading Pattern data s read. Use the media which has been formatted with IP-420. (1) Read the pattern data. 1 Select the pattern reading. When PATTERN READ button s pressed n the standard screen, the pattern readng screen s dsplayed.
  • Page 88 1. When PATTERN INFORMATION button F is pressed, the pattern information screen is displayed, and the pattern data information on the pattern No. which is being selected now can be confirmed. The screen return to the pattern reading screen with CANCEL button 2.

  • Page 89: Set The Enlargement/ReductOn RatO

    (2) Set the enlargement/reduction ratio. It s possble to read the enlarged or reduced pattern by settng enlargement/reducton rato beforehand. Enlargement/reducton s possble only when the readng data s VDT format data. 1 Set X enlargement/reduction ratio. When X ENLARGEMENT/REDUCTION RATIO SETTING button A s pressed, the X enlargement/reducton rato settng screen s dsplayed.
  • Page 90 4 Set the enlargement/reduction procedure. For the enlargement/reducton procedure, ether sttch length ncrease/decrease or number of sttches ncrease/decrease can be selected. When ENLARGEMENT/REDUCTION PROCEDURE SELECTION button C s pressed, the enlargement/ reducton procedure selecton screen s dsplayed. Enlargement/reducton procedure whch s beng selected now s dsplayed at the enlargement/reducton procedure selecton button.

  • Page 91: Set The KNd Of ReadNg Data

    (3) Set the kind of reading data. Object meda to read the pattern data and the knd of pattern data can be selected. It s possble to select the meda below. Meda whch s beng selected now s dsplayed at secton A wth pctograph.
  • Page 92 1 Set the object media. When OBJECT MEDIA SELECTION button B s pressed, the object meda settng screen s dsplayed. Select the knd of meda to read n from sewng machne memory and meda of C . The color of the selected button s changed When ENTER button D s pressed, the settng has been selected, and the screen returns to the pattern readng screen.

  • Page 93: Pattern Writing

    6-5. Pattern writing Pattern data s wrtten. Use the media which has been formatted with IP-420. (1) Write the pattern data. 1 Select the pattern writing. When PATTERN WRITING button s pressed n the standard screen, the pattern wrtng screen s dsplayed.

  • Page 94: Formatting Media (090)

    7. FORMATTING MEDIA (090) Meda s formatted. 1 Display the media format screen. When MODE button s pressed n the standard screen, the mode screen is displayed. Here press FORMAT button A , and the meda format screen s dsplayed. When FORMAT (functon code 090) s selected n the code lst screen, the format screen can be selected as...

  • Page 95: Trial Sewing

    8. TRIAL SEWING Confirm the shape or the like of the pattern created by using readout data or input function with trial sewng. For the tral sewng, the screen and the tem that can be set change accordng to the models. Explanaton below s the example n case of AMS-210EN.
  • Page 96 (c) When THREAD TENSION SETTING button C s pressed, the thread tenson reference value settng pop- up s dsplayed. Input the value wth TEN keys and keys F , determne the value wth ENTER button G , and return to the tral sewng preparaton screen.

  • Page 97: Performing The Trial Sewing

    8-2. Performing the trial sewing 1 Display the sewing screen of trial sewing. When SEWING PREPARATION button A s pressed, the sewng screen of tral sewng s dsplayed. 2 Perform trial sewing. Tral sewng can be performed wth the normal sewng machne operaton.
  • Page 98 4 Confirm the shape of pattern data. When SHAPE CHECK button I s pressed on the tral sewng preparaton screen, the shape checkng screen s dsplayed. The current poston s represented by (pnk crcle), the sewng start poston s represented by (blue dot) and the sewng end poston s represented by (pnk dot).

  • Page 99: Setting Function

    9. SETTING FUNCTION 9-1. Comment input Comment s set to the pattern data. 1 Display the comment input screen. Press COMMENT INPUT button A n the standard screen. The comment nput screen s dsplayed. When the setting of pattern information display section is the comment display ( 4 Perform the item setting of 14.

  • Page 100: Clamp Inversion Setting (091)

    9-2. Clamp inversion setting (091) Settng of clamp nverson s performed. 1 Display the inversion setting screen. Select and execute INVERSION SETTING (functon code 091) n the code lst screen, and the nverson settng screen s dsplayed. 2 Select the inversion procedure. For the clamp nverson moton, select AUTOMATIC INVERSION A or OPTIONAL INVERSION...

  • Page 101: Intermediate Presser Height Reference Value Setting (115)

    9-4. Intermediate presser height reference value setting (115) Intermedate presser heght reference value s set. 1 Display the intermediate presser height reference value setting screen. Select and execute INTERMEDIATE PRESSER HEIGHT REFERENCE VALUE (functon code 115) n the code lst screen, and the ntermedate presser heght reference value settng screen s dsplayed.

  • Page 102: Selecting Ending Procedure (110)

    10. SELECTING ENDING PROCEDURE (110) Settng of TRACE executon at the tme of end of nput s performed. 1 Display the ending procedure selection screen. Select and execute ENDING PROCEDURE SELECTION (functon code 110) n the code lst screen, and the endng procedure selecton screen s dsplayed.

  • Page 103: Allocating Functions To F1 Through F5 Buttons (112)

    11. ALLOCATING FUNCTIONS TO F1 THROUGH F5 BUTTONS (112) Functons are allocated to F buttons. Intal dsplay s as descrbed below. <Initial display screen> <AMS-E series> <LK-1900A series> <AMS-EN series> 1 Display the function selection and setting screen. Select and execute FUNCTION SELECTION AND SETTING (functon code 112) n the code lst screen, the functon selecton and settng screen s dsplayed.
  • Page 104 4 Display of the allocated function For the F button to whch the functon s allocated, the code of the allocated functon s dsplayed n G secton. Here, press F buttons through H , and allocaton to the next F button can be contnued. When CANCEL button I s pressed, the screen returns to the standard screen.

  • Page 105: Displaying Detailed Information On The Set Value (093)

    12. DISPLAYING DETAILED INFORMATION ON THE SET VALUE (093) Setting contents of the pattern data can be confirmed. 1 Display the set value reference screen. Select and execute SET VALUE REFERENCE (functon code 093) n the code lst screen, and the set value reference screen s dsplayed.
  • Page 106 Lst of the dsplay of contents n the set value reference screen Contents Display Total number of sttches Inverson settng Automatc nverson Optonal nverson X enlargng rato Y enlargng rato Enlargng/reducng reference pont X coordnate Enlargng/reducng reference pont Y coordnate Tracng settng Tracng Wthout tracng...

  • Page 107: Displaying Detailed Information On The Current Needle Position

    13. DISPLAYING DETAILED INFORMATION ON THE CURRENT NEEDLE POSITION The detailed information on the current needle position can be confirmed. 1 Display the contents of pattern display screen. Press PATTERN CONTENTS DISPLAY button n the standard screen, and the contents of pattern dsplay screen s dsplayed.
  • Page 108 Lst of the dsplay of contents n the contents of pattern dsplay screen Contents Display Knd of needle entry of the current needle poston s dsplayed. Head of Mdway of End of End of pattern pattern element pattern Knd of element of the current needle poston s dsplayed.

  • Page 109: Performing Setting Of Display

    14. PERFORMING SETTING OF DISPLAY Settng of the dsplayng procedure of the screen s performed. 1 Display the display setting screen. When DISPLAY SETTING button s pressed n the standard screen, the dsplay settng screen s dsplayed. When pressng buttons of A , B , C , D , and E , the screen that sets the dsplayng procedure s dsplayed.
  • Page 110 3 Perform the zoom setting Press ZOOM SETTING button B n the dsplay settng screen. The zoom settng screen s dsplayed. Select the magnification you desire to display from ZOOM AMOUNT button J . The color of the selected button s changed .
  • Page 111 5 Performing the selection of the display color Press DISPLAY COLOR SELECTION button D n the dsplay settng screen. The dsplay color selecton screen s dsplayed. The color dsplay of the pattern can be selected from color dsplayng only at the current pont O , dsplayng color of the lne wth tenson value P and dsplayng...
  • Page 112 6 Perform setting of the needle entry point display Press NEEDLE ENTRY POINT DISPLAY SETTING button E n the dsplay settng screen. The needle entry pont dsplay settng screen s dsplayed. Dsplayng all needle entry ponts S , and dsplayng 3 ponts of current, before and after, and top and end only of the pattern T can be selected.

  • Page 113: Element Forward/Backward (130 And 131)

    15. ELEMENT FORWARD/BACKWARD (130 and 131) Current needle poston can be moved before and after n the unt of element. 1 Select the element forward. Select and execute ELEMENT FORWARD (functon code 130) n the code lst screen, and the element moves to the last poston of the element ncludng the current needle poston. In case of the last poston, the element moves to the last poston of the next element.

  • Page 114: Direct Instructions By Touching The Screen

    16. DIRECT INSTRUCTIONS BY TOUCHING THE SCREEN The position to input can be directly instructed in the screen in case of creation or modification of the pattern. For the coordnate drect nstructons, there are the coordnate nstructons screen, and the needle entry and shape pont nstructons screen accordng to the contents of nstructons.
  • Page 115 4 Move the presser. When ENTER button E s pressed n the presser move confirmation screen, the presser moves to the position nstructed wth the cross cursor, and the screen returns to the specfyng poston screen. The presser moves linearly. When there is any obstacle on the way, the presser interferes with it.

  • Page 116: Needle Entry/Shape Points Direct Instructions

    16-2. Needle entry/shape points direct instructions Needle entry/shape ponts can be drectly selected. 1 Display the needle entry/shape points instructions screen. When COORDINATE INSTRUTIONS button s pressed n the screen specfyng needle entry/shape ponts such as the standard screen, the shape pont specfyng screen, etc., the needle entry/shape ponts nstructons screen s dsplayed.

  • Page 117: Performing Setting Of The Memory Switch Data

    17. PERFORMING SETTING OF THE MEMORY SWITCH DATA 17-1. Setting of the memory switch data is performed 1 Display the memory switch setting screen. Press MODE button n the standard screen to dsplay the mode screen. 2 Display the memory switch data list screen. When MEMORY SWITCH button A s pressed, the memory swtch data lst screen s dsplayed.

  • Page 118: Change Over The Display Language

    17-2. Change over the display language 1 Display the language selection screen. When LANGUAGE SELECTION button A s pressed n the memory swtch lst screen, the language selecton screen s dsplayed. Language beng selected at present s dsplayed n the language selecton button. 2 Select the language.

  • Page 119: Changing The Display Color Of The Current Point

    17-3. Changing the display color of the current point It s possble to change the dsplay color of the needle entry pont and the current pont of the shape pont. 1 Display the display color selection screen. When CURRENT POINT DISPLAY COLOR SELECTION button A s pressed n the memory swtch lst screen, the dsplay color selecton screen s dsplayed.

  • Page 120: Setting The Zigzag Sewing Output Method

    17-4. Setting the zigzag sewing output method When sewng data s to be wrtten on a medum or carryng out tral sewng, the method to output zgzag sewng ncluded n a pattern can be selected. When readng data onto the sewng machne model or PM-1 whch does not support zgzag sewng to be sewn wth the sewng start poston set at the "end"...

  • Page 121: Selecting The Function Code To Be Displayed

    18. SELECTING THE FUNCTION CODE TO BE DISPLAYED The functon code to be dsplayed can be selected n the code lst screen. 1 Display the code list display selection screen. When CODE LIST DISPLAY SELECTION button A s pressed n the mode screen of the body nput mode, the code lst dsplay selecton screen s dsplayed.

  • Page 122: Function Code List

    19. FUNCTION CODE LIST Functon codes are descrbed n the lst below. Function code list Remarks Thread trmmng command s nputted. 2nd orgn s set. Stop command s nputted. Reference pont to perform enlargng/reducng s set. Clamp nverson command s nputted. Sewng machne one revoluton s nputted.
  • Page 123 Function code Remarks Area classification command is inputted. Intermedate presser heght s set. * For LK-1900A series, it is not possible to select. Sewng machne stop command s nputted. Sewng data of jump feed s created. Sewng data of pont sewng s created. Sewng data of lnear lne and curve s created.
  • Page 124 Function code Remarks Sewng data of lnear offset sewng s created. Sewng data of splne offset sewng s created. Sewng data of arc offset sewng s created. Sewng data of crcle offset sewng s created. Sewng data of lnear double orderly sewng s created. Sewng data of splne double orderly sewng s created.
  • Page 125 Function code Fucntion Sewng data of arc overlapped reverse sewng s created. Sewng data of crcle overlapped reverse sewng s created. Mechancal control command s deleted. Speed of the created jump feed data s changed. Speed of the created sewng data s changed. Sttch length of the created sewng data s changed.
  • Page 126 Function code Function Needle entry pont s deleted and rear data moves. Needle entry pont s moved and rear data moves. Vertex of lnear lne s deleted and rear data moves. Vertex of lnear lne s moved and rear data moves. Needle entry pont s deleted and rear data does not move.
  • Page 127 Function code Function Meda s formatted. Settng of clamp nverson s performed. Sewng speed s nputted. Set value of pattern data s dsplayed. Current needle poston s taken as the reference, and orderly sewng pattern of Y symmetry s created. –...
  • Page 128 Function code Function Functon code s nputted. Tracng/not tracng of data at the tme of end/executon s set. Functon s allocated to F button. Thread tenson reference value s set. Intermedate presser heght reference value s set. * For LK-1900A series, it is not possible to select. –...
  • Page 129 Function code Function Element moves to the last poston of element ncludng current needle poston. In case of the last poston, t moves to the last poston of the next element. Element moves to the top poston of element ncludng current needle poston. In case of the top poston, t moves to the top poston of the prevous element.

  • Page 130: Setting Range List

    20. SETTING RANGE LIST <AMS-E series> Increase/ Max. value decrease Item Min. value Initial value unit. 12.7 mm 0.1 mm Ordnary sewng ptch 0.1 mm 2.0 mm 12.7 mm 0.1 mm Offset sewng ptch 0.1 mm 2.0 mm 12.7 mm 0.1 mm Zgzag sewng ptch 0.1 mm...
  • Page 131 <AMS-EN series> Increase/ Max. value decrease Item Min. value Initial value unit. 12.7 mm 0.1 mm Ordnary sewng ptch 0.1 mm 2.0 mm 12.7 mm 0.1 mm Offset sewng ptch 0.1 mm 2.0 mm 12.7 mm 0.1 mm Zgzag sewng ptch 0.1 mm 2.0 mm Reverse sewng ptch...
  • Page 132 <LK-1900A series> Increase/ decrease Item Min. value Max. value Initial value unit. 0.1 mm Ordnary sewng ptch 0.1 mm 10.0 mm 2.0 mm 0.1 mm Offset sewng ptch 0.1 mm 10.0 mm 2.0 mm 0.1 mm Zgzag sewng ptch 0.1 mm 10.0 mm 2.0 mm 0.1 mm...
  • Page 133 <AP-876> Increase/ decrease Item Min. value Max. value Initial value unit. 0.1 mm Ordinary sewing pitch 0.1 mm 6.0 mm 2.0 mm 0.1 mm Offset sewing pitch 0.1 mm 6.0 mm 2.0 mm Zigzag sewing pitch 0.1 mm 2.0 mm 0.1 mm 6.0 mm Reverse sewing pitch...

  • Page 134: Backup

    21. BACKUP The data created when pressing the backup button from the standard screen and performing the trial sewing is backed up in the sewing machine. The continuation can be edited by using the backup data when moving to the body input next time. Overwriting is performed on the current pattern when performing backup or trial sewing.

  • Page 135: Error Code List

    22. ERROR CODE LIST When an error occurs during motion of the body input mode, the error screen is displayed. Error code is displayed at A , pictograph showing description of error at B , and error message at C in the error screen. Press RESET button D to return to the normal operation.
  • Page 136 Error No. Display Error description and corrective measure File size over E019 File is too large. Memory size is over. E024 • Number of stitches that can be created with one element exceeds the limit. Create by dividing. E029 Lid of media slot is open. Needle is not in a proper position.
  • Page 137 Error No. Display Error description and corrective measure Feeding frame is lifting. E431 • Lower the frame. Proper operation has not been performed. E432 • In case of circle and arc, two points of the shape point are not specified. •...

  • Page 138: Message List

    23. MESSAGE LIST The list is the message screen displayed for confirmation of execution of processing in the body input mode. Message No. is displayed at A , pictograph showing the description of message at B , and message at C in the message screen. Press ENTER button D to continue processing, and press CANCEL button...
  • Page 139 Message No. Display Description of message M509 Sewing mode conversion confirmation Data being created is erased and mode is converted to sewing mode. OK ? • When it is necessary to store the data, press CANCEL button to store. Standard zigzag change confirmation M510 Zigzag stitch is changed to standard zigzag stitch.

Table of Contents