Page 1
Projector CP-X8150/CP-X8160/ CP-WX8240/CP-WX8255/ CP-SX8350/CP-WU8440/CP-WU8450 User's Manual (detailed) Operating Guide – Technical Example of computer signal Resolution (H x V) H. frequency (kHz) V. frequency (Hz) Rating Signal mode 720 x 400 37.9 85.0 VESA TEXT 640 x 480 31.5 59.9...
Page 2
VESA Reduced Blanking *1) Supported except for HDMI input. *2) Only for CP-X8150, CP-X8160 and CP-SX8350. *3) Only for CP-WX8240, CP-WX8255, CP-WU8440 and CP-WU8450. *4) Only for CP-WU8440 and CP-WU8450, but except for HDMI input. NOTE • Be sure to check jack type, signal level, timing and resolution before connecting this projector to a computer.
Page 3
Initial set signals Initial set signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu. Back porch (B) Front porch (D) Back porch (b)
Page 4
Connection to the ports Connection to the ports NOTICE ►Use the cables with straight plugs, not L-shaped ones, as the input ports of the projector are recessed. ►Only the signal that is input from the COMPUTER IN1 or IN2 can be output from the MONITOR OUT port.
Page 5
Connection to the ports (continued) COMPUTER IN2 G/Y, B/Cb/Pb, R/Cr/Pr, BNC jack x5 <Computer signal> • Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive) • H/V. sync. signal: TTL level (positive/negative) • Composite sync. signal: TTL level <Component video signal> •...
Page 6
Connection to the ports (continued) COMPONENT Cb/Pb, Cr/Pr RCA jack x3 • Component video signal, Analog: -Y with composite sync, 1.0±0.1Vp-p, 75Ω terminated -Cb/Pb, 0.7±0.1Vp-p, 75Ω terminated -Cr/Pr, 0.7±0.1Vp-p 75Ω terminated • System: 480i@60, 480p@60, 576i@50, 720p@50/60, 1080i@50/60, 1080p@50/60 S-VIDEO Mini DIN 4pin jack •...
Page 7
Connection to the ports (continued) AUDIO IN1, AUDIO IN2 Ø3.5 stereo mini jack • Analog, 500 mVrms, 47kΩ input impedance AUDIO IN3 AUDIO OUT RCA jack x2 RCA jack x2 • Analog, 500 mVrms, 47kΩ input impedance • Analog, 500 mVrms, 1kΩ output impedance CONTROL D-sub 9pin plug * About the details of RS-232C communication,...
Connection to the ports (continued) RJ-45 jack * About the details of network communication, please refer to the Network Guide. Signal Signal Signal USB TYPE A USB TYPE B USB A type jack x2 USB B type jack Signal Signal - Data - Data + Data...
Page 9
Connection to the ports (continued) To input SCART RGB signal; RCA plugs SCART cable Audio L (plug) Audio R Video SCART connector (jack) To input SCART RGB signal to the projector, use a SCART to RCA cable. Connect the plugs refer to above ex. For more reference, please consult your dealer.
Page 10
RS-232C Communication RS-232C Communication When the projector connects to the computer by RS-232C communication, the projector can be controlled with RS-232C commands from the computer. For details of RS-232C commands, refer to RS-232C Communication / Network command table (&19). Connection Turn off the projector and the computer.
Page 11
RS-232C Communication (continued) Communicaion settings 1. Protocol 19200bps, 8N1 2. Command format ("h" shows hexadecimal) Byte Number Command Header Data Header Data Setting Action Type code size flag code Packet Action <SET>Change setting to desired value [(cL)(cH)] (aL) (aH) 01h 00h (bL) (bH) (cL) (cH) by [(bL)(bH)].
RS-232C Communication (continued) 3. Response code / Error code ("h" shows hexadecimal) (1) ACK reply: 06h When the projector receives the Set, Increment, Decrement or Execute command correctly, the projector changes the setting data for the specified item by [Type], and it returns the code. (2) NAK reply: 15h When the projector cannot understand the received command, the projector returns the error code.
Page 13
Command Control via the Network Command Control via the Network When the projector connects network, the projector can be controlled with RS- 232C commands from the computer with web browser. For details of RS-232C commands, refer to RS-232C Communication / Network command table (&19).
Page 14
Command Control via the Network Communicaion Port The following two ports are assigned for the command control. TCP #23 TCP #9715 Configure the following items form a web browser when command control is used. Port Settings Click the [Enable] check box to open [Network Control Port1 (Port: 23)] to use TCP #23.
Command Control via the Network (continued) Command control settings [TCP #23] 1. Command format Same as RS-232C communication, refer to RS-232C Communicaton command format. 2. Response code / Error code ("h" shows hexadecimal) Four of the response / error code used for TCP#23 are the same as RS-232C Communication (1)~(4).
Page 16
Command Control via the Network (continued) 2. Response code / Error code ("h" shows hexadecimal) The connection ID is attached for the TCP#23's response / error codes are used. The connection ID is same as the sending command format. (1) ACK reply: 06h + ××h (××h : connection ID) (2) NAK reply: 15h + ××h (3) Error reply: 1Ch + 0000h + ××h...
Page 17
Network Bridge Communication Network Bridge Communication This projector is equipped with NETWORK BRIDGE function. When the projector connects to the computer by wired or wireles LAN communicaton, an external device that is connected with this projector by RS- 232C communication can be controlled from the computer as a network terminal. For details, see the 6.
Network Bridge Communication Communication settings For communication setting, use the COMMUNICATION menu in the OPTION - SERVICE menu Item Condition BAUD RATE 4800bps / 9600bps / 19200bps / 38400bps Data length 8 bit (fixed) PARITY NONE/ODD/EVEN Start bit 1 bit (fixed) Stop bit 1 bit (fixed) Transmission method...
Page 19
RS-232C Communication / Network command table RS-232C Communication / Network command table Command Data Names Operation Type Header Action Type Setting code Turn off BE EF 06 00 2A D3 01 00 00 60 00 00 Turn on BE EF 06 00 BA D2 01 00...
Page 20
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code LENS MEMORY BE EF 06 00 A0 91 02 00 0D 24 00 00 LENS SHIFT - V LENS MEMORY BE EF 06 00 E4 91 02 00 0E 24...
Page 21
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code 1 DEFAULT BE EF 06 00 07 E9 01 00 A1 30 20 00 1 CUSTOM BE EF 06 00 07 FD 01 00 A1 30 10 00 2 DEFAULT...
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code BE EF 06 00 C4 FE 02 00 95 30 00 00 User GAMMA Increment BE EF 06 00 A2 FE 04 00 95 30 00 00 Point 6...
Page 23
08 20 09 00 (*) NATIVE BE EF 06 00 5E D7 01 00 08 20 08 00 BE EF 06 00 AD D0 02 00 08 20 00 00 (*) Supported except for CP-X8150 and CP-X8160. (continued on next page)
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code BE EF 06 00 91 70 02 00 09 22 00 00 OVER SCAN Increment BE EF 06 00 F7 70 04 00 09 22 00 00 Decrement...
Page 25
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code AUTO BE EF 06 00 E6 70 01 00 12 22 0A 00 NTSC BE EF 06 00 86 74 01 00 12 22 04 00 BE EF 06 00...
Page 26
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code AUTO KEYSTONE V Execute BE EF 06 00 E5 D1 06 00 0D 20 00 00 EXECUTE BE EF 06 00 B9 D3 02 00 07 20 00 00...
02 00 FRONT / CEILING BE EF 06 00 37 D2 01 00 01 30 03 00 BE EF 06 00 F4 D2 02 00 01 30 00 00 (*) Only for CP-X8150, CP-X8160, CP-WX8240 and CP-WX8255. (continued on next page)
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code NORMAL BE EF 06 00 D6 D2 01 00 01 60 00 00 STANDBY SAVING BE EF 06 00 46 D3 01 00 01 60 01 00 MODE...
Page 29
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code BE EF 06 00 CD CC 02 00 60 20 00 00 VOLUME - Increment BE EF 06 00 AB CC 04 00 60 20 00 00 COMPUTER IN1...
Page 30
RS-232C Communication / Network command table (continued) RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code AUDIO IN1 BE EF 06 00 6E DC 01 00 30 20 01 00 AUDIO IN2 BE EF 06 00 9E DC...
RS-232C Communication / Network command table (continued) RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code AUDIO IN1 BE EF 06 00 D6 DD 01 00 32 20 01 00 AUDIO IN2 BE EF 06 00 26 DD...
Page 32
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code TÜRKÇE BE EF 06 00 07 D6 01 00 05 30 0F 00 DANSK BE EF 06 00 A7 DF 01 00 05 30 11 00 ČESKY BE EF...
Page 33
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code TEST PATTERN BE EF 06 00 43 D9 01 00 22 30 00 00 DOT-LINE 1 BE EF 06 00 D3 D8 01 00 22 30 01 00 DOT-LINE 2...
Page 34
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code NORMAL BE EF 06 00 32 78 01 00 25 22 00 00 SOURCE SKIP - SKIP BE EF 06 00 A2 79 01 00 25 22 01 00...
Page 35
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code SLIDESHOW BE EF 06 00 9A 2B 01 00 00 36 22 00 MY IMAGE BE EF 06 00 5A 3D 01 00 00 36 16 00 MESSENGER...
Page 36
RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code SLIDESHOW BE EF 06 00 DE 2B 01 00 03 36 22 00 MY IMAGE BE EF 06 00 1E 3D 01 00 03 36 16 00 MESSENGER...
Page 37
PJLink command PJLink command Commands Control Description Parameter or Response 0 = Standby POWR Power Contorol 1 = Power On 0 = Standby 1 = Power On POWR ? Power Status inquiry 2 = Cool Down 11 = COMPUTER IN 1 12 = COMPUTER IN 2 21 = COMPONENT 22 = S-VIDEO...
Page 38
11 12 21 22 23 31 33 41 51 52 Responds with the name set in the item NAME ? Projector Name inquiry PROJECTOR NAME of the NETWORK menu Manufucturer's Name INF1 ? HITACHI inquiry CP-X8150 CP-X8160 CP-WX8240 CP-WX8255 INF2 ? Model Name inquiry CP-SX8350 CP-WU8440 CP-WU8450...