Advertisement
Quick Links
PLEASE: CALL US IF YOU HAVE DIFFICULTY BEFORE YOU
RETURN THIS TO THE STORE.
PARTS HOT LINE PHONE: 574-848-7491
HELPFUL HINTS:
If your spreader does not spread evenly, be sure the FRONT on the gear box points to the front of the spreader. The impeller must
turn clockwise. Reversing the gearbox will cause the impeller to turn counter clockwise. Clean the impeller plate after each use.
Fertilizer stuck on the impeller blades will cause uneven spreading.
Your spreader is designed to be pushed at three miles per hour, which is a brisk walking speed. Slower or faster speeds will change
the spread patterns. Wet fertilizer will also change the spread pattern and flow rate. Clean your spreader thoroughly after each use.
Wash between the shut off plate and bottom of the hopper.
Gears are permanently lubricated at the factory. Do not open the gearbox or dirt may enter.
1.
Remove and identify loose parts from carton.
ASSEMBLY and OPERATING INSTRUCTIONS
EarthWay
M24
Series
SSD
2.
Position hopper on side. Install frame using (4) 1/4-20
x 1-1/2" Pan Head Philips machine screws and (4) 1/4-20
nylon insert locknuts. First put bolts through holes in
frame then through holes in bottom of hopper. Secure
with locknuts. Tighten these locknuts now.
®
Ev-N-Spred
Broadcast Spreader
PAGE 1
Advertisement
Related Manuals for EarthWay Ev-N-Spred M24SSD Series
Summary of Contents for EarthWay Ev-N-Spred M24SSD Series
- Page 1 ASSEMBLY and OPERATING INSTRUCTIONS ® EarthWay Ev-N-Spred Series Broadcast Spreader PLEASE: CALL US IF YOU HAVE DIFFICULTY BEFORE YOU RETURN THIS TO THE STORE. PARTS HOT LINE PHONE: 574-848-7491 HELPFUL HINTS: If your spreader does not spread evenly, be sure the FRONT on the gear box points to the front of the spreader. The impeller must turn clockwise.
- Page 2 Install impeller onto pinion shaft. Insert 1/8” x 1 ” cotter pin through impeller then through pinion shaft. Use hole nearest gear box. Spread cotter pin to prevent from falling out. Install gear box by inserting the pinion shaft into hole in center of hoppers bottom.
- Page 3 stall drive wheel to axle using pin hole nearest to lower handles as shown. Insert 2” cotter pin through wheel and through axle. Bend with pliers to prevent pin from falling out. Next slide the wheel spacer and then the outer wheel and cotter pin through the axle only. Install inner coast wheel to axle, then wheel spacer and then the outer coast wheel and install cotter pin using outside hole.
- Page 4 Install handle shaft to lower handles and pivot & bracket assembly as shown. Using (4) 1 ½” bolts and (4) locknuts. Tighten bolts and nuts now. nstall flattened end of control rod in to lever on gauge as shown. Turn to lock in place. Next push lever forward to setting Install (1) 1/4-20 regular nut (not a locknut) on to con- “0”.
-
Page 5: Warranty
OPERATING INSTRUCTIONS WARRANTY Before filling hopper, become familiar with the operation of EARTHWAY guarantees this product to be free of defects in origi- this spreader. nal workmanship and materials for a period of 90-days from sale to Obtain proper setting for material to be used from the the original user. - Page 6 EarthWay ® Products, Inc. P.O. Box 547 Bristol, Indiana 46507 (574) 848-7491 www.earthway.com Ke y # Part # De scription Ke y # Part # De scription 40003 Screen *1/4-20 X 2 1/4" Bolt 60219 Hopper Assembly, Includes Key #7 & 8 60299 Pivot &...
Need help?
Do you have a question about the Ev-N-Spred M24SSD Series and is the answer not in the manual?
Questions and answers