Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Harman Kardon HKTS 7
Summary of Contents for Harman Kardon HKTS 7
- Page 1 HKTS 7 Home Theater Speaker System OWNER’S MANUAL...
-
Page 2: Table Of Contents
Table of Contents 3 Introduction 4 SUB-TS7 Subwoofer Amplifier Panel Controls and Connections 6 Speaker Placement 7 Mounting Options Declaration of Conformity 8 Speaker Connections Speaker-Level Connection Guide Dolby Digital or DTS (or Other Digital Surround Mode) Connection Dolby Pro Logic (Non-Digital) – Line Level We, Harman Consumer Group, Inc. -
Page 3: Introduction
Introduction Introduction The HKTS 7 subwoofer is easy to connect to your Included system, since it’s equipped with a special sub- Thank you for purchasing the Harman Kardon woofer input for use with equipment that has a HKTS 7, with which you’re about to begin many dedicated subwoofer connection that carries a years of listening enjoyment. -
Page 4: Rear Panel Connections
Rear Panel Connections HKTS 7 or HKTS 7BQ System Subwoofer-Level Control Line-Level Subwoofer (SUB) Input Master Power Switch High-Cut (Low-Pass) Filter Switch Line-Level Full-Range Inputs AC Power Cord Trigger Input Speaker-Level Outputs Phase Switch Speaker-Level Inputs Subwoofer-Level Control: Volume Trigger Input: Some receivers or sound... - Page 5 Rear Panel Connections Line-Level Subwoofer (SUB) Input: Con- Master Power Switch: Place this switch in nect the subwoofer output of a receiver with the “•” position to power-on the SUB-TS7 sub- digital surround sound decoding, such as Dolby* woofer. The SUB-TS7 will then be either in the Digital or DTS ®...
-
Page 6: Speaker Placement
Speaker Placement Color-Coding System Center Channel Speaker Surround Speakers The HKTS 7 uses the channel color-coding system established by the Consumer Electronics White Association to make setting up your home 0-0,55 m theater speaker system as easy as possible. Your... -
Page 7: Mounting Options
Mounting Options Wall-Mounting for Satellites The bracket has two openings on top: a round Wall-Mounting for the Center screw hole, and an arc-shaped opening in front Speaker Unscrew the bolt that attaches the black shelf of it. The speaker cable should be threaded stand to the bottom of the speaker. -
Page 8: Speaker Connections
CEA standard and therefore use a color other than red or black for the (+) terminal to indicate some speaker positions: e.g., surround left. Although the HKTS 7 system has red and black collars on the individual speaker terminals to denote the positive and negative connections,... -
Page 9: Dolby Digital Or Dts (Or Other Digital Surround Mode) Connection
Speaker Connections Dolby Digital or DTS ® jack to the LFE output or subwoofer output Make sure that you have configured your sur- (or Other Digital Surround Mode) on your receiver or amplifier. Connect each round-sound processor for “Subwoofer On.” Connection speaker to the corresponding speaker terminals The front left, front right, center and rear speak-... -
Page 10: Dolby Pro Logic (Non-Digital) - Line Level
Speaker Connections Dolby Pro Logic (Non-Digital) – Use both the left and right inputs on the sub- If your receiver/processor has a built-in low- Line Level woofer if your receiver or processor has both left pass-crossover filter for the subwoofer output, and right line-level outputs. -
Page 11: Dolby Pro Logic (Non-Digital) - Speaker Level
Speaker Connections Dolby* Pro Logic* (Non-Digital) – Connect your receiver or amplifier’s front left Connect your receiver or amplifier’s center, left Speaker Level and right speaker terminals to the left and right and right surround-speaker terminals to the terminals on the subwoofer that are marked corresponding terminals on the back of your Use this installation method for Dolby Pro Logic “High Level In.”... -
Page 12: Operation
Operation Move the Master Power switch (marked Volume Additional Bass Adjustments “Power” ) to the “•” (On) position to use the Volume can be adjusted using the Subwoofer In addition to the volume adjustments described subwoofer. The SUB-TS7 subwoofer will auto- Level Control (above), as shown below. -
Page 13: Troubleshooting
Troubleshooting If there is no sound from • Check that receiver/amplifier is on and a source is playing. any of the speakers: • Check that the powered subwoofer is plugged in, its Power switch is switched on to the “ON •” position. •... -
Page 14: Specifications
Specifications HKTS 7 CEN-TS7 SUB-TS7 System Center Subwoofer Frequency Response Recommended Power Amplifier 35Hz – 20kHz (–6dB) 10 – 80 Watts 100 Watts RMS Impedance Bass 8 Ohms nominal 10" Woofer, bass-reflex enclosure SAT-TS7 Sensitivity Dimensions (H x W x D) - Page 16 250 Crossways Park Drive, Woodbury, New York 11797 www.harmankardon.com Harman Consumer Group, Inc.: 2, Route de Tours, 72500 Château-du-Loir, France © 2007 Harman Kardon, Incorporated Part 406-000-01009...
Need help?
Do you have a question about the HKTS 7 and is the answer not in the manual?
Questions and answers