Table of Contents
Advertisement
Available languages
Available languages
TROUBLESHOOTING
r
First try the solutions suggested here or visit our website at www.whirlpool.com/help
for assistance and to possibly avoid a service call.
Fabric Damage (cont.)
Incorrect dispenser
operation
Liquid chlorine bleach may have been
added incorrectly.
Clogged dispensers or laundry
products dispensing too soon.
Liquid chlorine bleach not
used in dispenser.
Do not pour liquid chlorine bleach directly onto load. Wipe up
bleach spills.
Undiluted bleach will damage fabrics. Do not use more than
recommended
by manufacturer.
Do not place load items on top of bleach dispenser when
loading and unloading washer.
Do not overfill dispenser. Overfilling causes immediate dispensing.
Always select Fabric Softener option to assure proper dispensing.
Load dispensers before starting a cycle.
Htis normal for small amounts of water to be remain in dispenser at
the end of the cycle.
Homes with low water pressure may result in residual powder in the
dispenser. To avoid, select a warmer wash temperature if possible,
depending on your load.
Use only liquid chlorine bleach in the Bleach dispenser.
oL (overloaded)
appears in display
uL (unbalanced load)
appears in display
LF (too long to fill)
appears in display
Ld (too long to drain
water ) appears in
display
HC (Hot and Cold
hoses reversed)
appears in display
Sd (Excess suds)
appears in display
Load too large.
Load not balanced. The washer is
running a load-balance
correction
routine.
Washer taking too long to fill.
Drain extends more than
4.5" (114 mm)into
standpipe.
Washer taking too long to drain
water. Drain extends more than
4.5" (114 mm)into
standpipe.
Hot and cold inlet hoses have been
installed incorrectly.
Excessive suds in washer. Washer is
running a suds reduction routine.
Hfan overload is detected, the washer will drain any water and
detergent in the washer. Remove several items and add HE
detergent. Close lid and press START/PAUSE.
Allow the machine to continue. Hfthe dial is flashing and the
machine has stopped, redistribute
the load, close the lid, and
press START/PAUSE.
Check plumbing for correct drain hose installation. Use drain
hose form and attach securely to drainpipe or tub. Do not tape
over drain opening. See "hstallation
hstructions'.
Check plumbing for correct drain hose installation. Use drain
hose form and attach securely to drainpipe or tub. Do not tape
over drain opening.
Lower drain hose if the end is higher than 96" (2.4 m) above
the floor. Remove any clogs from drain hose. See "Installation
Instructions".
This code will appear at the end of the wash cycle to indicate
that cold water hose is connected to the hot water inlet and hot
water hose is connected to the cold water inlet.
Allow the washer to continue. Use only HE detergent.
Always measure detergent, and base detergent quantity on
load size. Follow detergent manufacturer's
instructions.
If the
dial is flashing, reselect your desired cycle using a cold wash
temperature,
and press START/PAUSE. Do not add detergent.
dL (Lid cannot lock)
An item in the load may be keeping
Check for items directly under the lid.
appears in display
the lid from locking.
lid (Lid opened)
Washer lid left open.
Close the lid to clear the display. If the lid is left open for more
appears in display
than 10 minutes, the cycle will reset and water in the washer
will drain.
dU (Lid cannot unlock)
Objects on washer lid prevent it from
Remove objects, such as a basket of laundry, from the top of
appears in display
unlocking,
the washer.
F## code (F-type
System error code.
Press START/PAUSE once to clear the code. Then press
error code) appears
START/PAUSE again to restart washer. If code appears again,
in display
call for service.
17
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
Need help?
Do you have a question about the Cabrio WTW8200YW0 and is the answer not in the manual?
Questions and answers
Washer not cleaning spots or stains
The Whirlpool Cabrio WTW8200YW0 washer may not be cleaning spots or stains due to the following reasons:
1. Incorrect Detergent Usage – Ensure you are using only HE (High Efficiency) detergent and measuring it correctly. Using too much or too little detergent can affect cleaning performance.
2. Fabric Damage or Improper Loading – Ensure garments are loaded in loose heaps evenly around the washplate and not directly over the center. Overloading or tightly packed loads can prevent proper washing.
3. Cycle Selection – Use the correct wash cycle for the type of fabric being washed. Refer to the garment care labels and the washer’s Cycle Guide to match the load with the best cycle.
4. Garment Care Instructions – Always follow the manufacturer's care label instructions on clothing to ensure proper washing.
5. Adding Clothes After Start – If adding garments after the cycle has started, only add one or two additional items to ensure proper cleaning.
These factors can impact the washer’s ability to remove spots or stains effectively.
This answer is automatically generated
Can you remove the washer plate and clean under it
The provided context does not mention whether the washplate on the Whirlpool Cabrio WTW8200YW0 can be removed for cleaning underneath.
This answer is automatically generated
My 90 year old father is having an issue with his washing machine not spinning all of the water out of his clothes. Is there any thing he can do to trouble shoot this problem. What things could be causing this to happen?
If the Whirlpool Cabrio WTW8200YW0 washing machine is not spinning out water, follow these troubleshooting steps:
1. Check for Small Items Clogging the Pump – Empty pockets and use laundry bags for small items that may be stuck in the pump or between the basket and tub, slowing drainage.
2. Select an Appropriate Spin Speed – Low spin speed programs remove less water. Use a higher spin speed if needed.
3. Ensure the Load is Balanced – Overloaded or unbalanced loads can prevent proper spinning. Distribute the load evenly.
4. Use the DRAIN & SPIN Cycle – This cycle removes excess water if clothes remain too wet.
5. Check Drain Hose Installation – Ensure the drain hose is properly installed, not extending more than 4.5 inches into the standpipe, and not positioned higher than 96 inches above the floor.
6. Remove Clogs from the Drain Hose – Clear any blockages that may be preventing proper drainage.
7. Use Only HE Detergent – Excess suds from non-HE or too much HE detergent can slow or stop draining. Use the correct amount of HE detergent.
8. Run RINSE & SPIN if Excess Suds Are Present – This cycle removes extra suds without adding more detergent.
9. Check Water Supply Connections – Ensure both hot and cold inlet hoses are correctly connected and not clogged or kinked.
These steps can help resolve the issue and restore normal spinning and draining functions.
This answer is automatically generated
Where is the water inlet filter and if there is where is the drain filter located?
The location of the water inlet filter and drain filter on the Whirlpool Cabrio WTW8200YW0 is not specified in the provided information.
This answer is automatically generated