Table of Contents
Advertisement
Your warranty will be in effect when you send in your warranty card
Event, Event Electronics, 20/20, 2020p and 20/20bas are trademarks of Event Electronics, LLC.
Specifications subject to change without notice
© 1996, 1997, 1998 Event Electronics, LLC
Event Electronics, LLC
P.O. Box 4189
Santa Barbara, CA 93140-4189
Voice: (805) 566-7777
Fax: (805) 566-7771
Web: www.event1.com
E-mail: info@event1.com
Printed in USA
6/98 1127
20/20™ DIRECT FIELD MONITOR
20/20p™ POWERED MONITOR
20/20bas™ BIAMPLIFIED SYSTEM
I
......................................................................
NTRODUCTION
U
......................................................................... 1
NPACKING
S
................................................................................ 1
ETUP
20/20 C
E
ONNECTIONS TO AN
XTERNAL
A
MPLIFIER
20/20bas C
O
ONNECTIONS AND
20/20p C
O
ONNECTIONS AND
PERATION
C
M
....................................................... 7
ARE AND
AINTENANCE
20/20 S
........................................................... 7
PECIFICATIONS
............................. 2
.................................. 3
PERATION
.................................. 5
1
Advertisement
Table of Contents
Related Manuals for Event electronics 20/20
Summary of Contents for Event electronics 20/20
- Page 1 Santa Barbara, CA 93140-4189 Your warranty will be in effect when you send in your warranty card Event, Event Electronics, 20/20, 2020p and 20/20bas are trademarks of Event Electronics, LLC. Specifications subject to change without notice © 1996, 1997, 1998 Event Electronics, LLC Event Electronics, LLC P.O.
- Page 2 The front-mounted low air restriction bass port also adds to our monitors’ larger acoustic signature. The 20/20bas Biamplified System monitors build on the foundation of the passive 20/20 and realize the proven benefits of biamplification, including lowered distortion, smoother amplitude and phase response, extended bandwidth and convenience.
-
Page 3: Specifications
ONNECTIONS TO AN XTERNAL passive Event 20/20 monitors present a 4 ohm nominal load impedance to the amplifier. Amplifiers rated for 8 ohm minimum loads are generally not suitable and may even suffer damage if used. We recommend using a power amplifier rated in the range of 100-200 watts per channel into 4 ohms. -
Page 4: Power Switch
220-240V~ 50/60Hz or 100V~ 50/60Hz, 400VA; Power via detachable 3 circuit IEC type linecord 5/8" vinyl laminated lock-mitered MDF Cabinet: Dimensions: 10¼" W x 14¾" H x 11¾" D Weight: 33 lbs. Powered Main Cabinet; 22 lbs. Passive 20/20 Satellite... -
Page 5: Powered Monitor Connections/Operation
ONNECTIONS AND Please refer to Figure 3. A The Channel A amplifier section powers the external passive HANNEL 20/20 monitor through the A output connector. The Channel B amplifier section powers the internal 20/20 HANNEL monitor. NPUT ONNECTOR This jack has gold plated terminals and accepts both XLR and ¼"... -
Page 6: Rear Panel
Do not expose the rear panel controls, connectors, or the speaker elements to moisture. Check the 20/20 and 20/20p’s external speaker wire connections occasionally for tightness. The bare wires attached to the binding post can become loose over time increasing the resistance of the connection. -
Page 7: Power Connector
OWER ONNECTOR This connector accepts the detachable linecord. Use the linecord supplied with your monitors and make sure it is fully seated into the Power Inlet connector. For safety reasons, do not attempt to defeat the linecord’s ground connection. 2. T 20/20bas IGURE REAR PANEL...
Need help?
Do you have a question about the 20/20 and is the answer not in the manual?
Questions and answers