Advertisement
Warranty .......................................
2
Safety Rules ....................................
2
Unpacking .....................................
2
Assembly .......................................
2
Operation ....................................
2-3
Maintenance ....................................
3
Parts Illustration and List .........................
4-5
FULL ONE YEAR WARRANTY
if this product fails due to a defect in material or workmanship
within one year from the date of pumhase, Sears will at its
option repair or repiaae it free of charge.
Contact your nearest Sears Service Center to arrange for
product repair, or return this product to place of purchase for
replacemnt.
ti this product is used for commercial or rental purposes, this
warranty will apply for 90 days from the date of purchase.
This warranty gives you specific legal rights, and you may
also 'have other rightswhich vary from state to state.
Sears, Roebuck and Co., Dept 817WA, Hoffman Estates, IL
6O179
• Understand and follow all safety instructions supplied with drill
pre._s,or other machines on which milling table is used,
• Mount table to work surface by polting or clamping base
securely in four mounting locations.
• Be alert and think clearly. Always check your set up; for
example, rotate accessory by hand before applying power.
• Make sure workpiaces, guides, fences, or power heads are
securely clamped, as applicable, Do not force accessory.
Be positive you are feeding in right direction.
• Never feed "_ree-hancF without table guide and/or guides.
Use vises or appropriate clamps to secure each workplace,
securely clamping them to work surface.
• Use only accessories designed for mill. Keep power tool
guard in place. Dress properly. Do not wear jewelry, gloves,
or loose clothing.
• Wear a face shield or safety glasses. Never place hands in
jeopardy.
Check for shipping damage. If damage has occurred, a claim
must be filed with carrier immediately. Check for complete-
ness. immediately report missing parts to dealer.
NOTE:
The tool has been coated with a protective coating.
in order to ensure proper fit and operation, the coating must
be removed. Removed coating with mild solvents, such as
mineral spirits, and a soft cloth. Nonflammable solvents are
recommended. After cleaning, cover all exposed surfaces with
a light coating of oil. Be sure to lubricate table as described in
"Maintenance".
WARNING:Never
use highly volatile solvents. Avoid getting
cleaning solution on paint as it may tend to deteriorate these
finishes. Use soap and water on painted components.
Refer to Figure 1,
• Attach each handle (Key No. g) to handwheai (Key No. 13)
with handle screw (Key No. 10).
• Tighten each screw securely.
• Attach one hendwhee[ (Key No. 13) to cross feed screw
(Kay No. 21) with key (Key No. 5) and locking nut (Key No.
12).
• Attach two handwhesls to longitudinal feed screw (Key No.
7) with keys and locking nuts.
• Tighten each locking nut securely.
DESCRIPTION
Craftaman Compound Milling Table is manufactured from cast
iron and steel The table fits most drill presses. Milling opera-
tions can be done by moving work right and left (longitudinal),
or front and back (cross) directions. The table can also be
used to accurately position or index a workpiece under a drill
but when not doing milling operations. A U-clamp hold down
set is included with the table.
• The Milling Table is heavy. Do not lift it by the crank handles.
• Make sure that drill press table is fastened securely, does
not shift in any direction, and is clean and free of nicks and
burrs.
,, Center table on drill press. There are two 5/,. slots on each
side of base for secudng to dn'll press.
• If drill press table has T-slots, use four T-nut clamp assam-
bliss, two on each side, to secure milling table. Clamp
assemblies are not supplied.
• If drill press table has slots to fit T-nuts, use four bolts with
heavy washem (not supplied) and attach T-nuts to bottom of
table. Secure milling table w_th locking nuts (not supplied).
• If drill press table does not have T-slots or threaded holes,
drill and tap four holes, matching location of %" slots in
base. Fasten milling table with four bolts and heavy wash-
sis (not supplied).
SPECIFICATIONS
Table ....................................
18'/, x 6"
T-Slots .......................................
%="
T-Slots (center to center) ........................
2%_"
Longitudinal Travel ..............................
12"
Cross Travel ...................................
8"
Value of One Division
........................
0,0008"
Cross Travel
per One Revolution ..........................
0.0787"
Longitudinal
Travel
per One Revolution
..........................
0.0787"
2
Advertisement
