Table of Contents
Advertisement
Available languages
Available languages
PROGRAMMING
NOTICE: If this Security_ _garage door opener is operated with a non-rolling code transmitter, the technical measure in
the receiver of the garage door opener, which provides security against code-theft devices, will be circumvented. The
owner of the copyright in the garage door opener does not authorize the purchaser or supplier of the non-rolling code
transmitter to circumvent that technical measure.
Your garage door opener has already been programmed at the factory to operate with your hand-held remote control.
The door will open and close when you press the large push button.
Below are instructions for programming your opener to operate with additional Security÷ ® remote controls.
To Add
or Reprogram
a Hand-held
Remote
Control
USING THE "LEARN"
BUTTON
USING THE PREMIUM
CONTROL
CONSOLE
1. Press and release the "learn" button
on the motor unit. The learn indicator
light will glow steadily for 30 seconds.
2. Within 30 seconds,
press and hold
the button on the hand-held
remote*
that you wish to operate your garage
door.
3. Release the button when the motor
unit lights blink. It has learned the
code. If light bulbs are not installed,
two clicks will be heard.
\1/
1. Press and hold the button on the
hand-held
remote* that you wish to
operate your garage door.
2. While holding the remote button,
press and hold the LIGHT button on
the Premium
Control Console.
3.
Continue
holding both buttons while
you press the push bar on the
Premium
Control Console
(all three
buttons are held).
4. Release buttons when the motor unit
lights blink. It has learned the code. If
light bulbs are not installed,
two clicks
will be heard.
i s-_,s-_ ,el
]
$2
\1
/
To Erase
All Codes
From
Motor
Unit
Memory
To deactivate
any unwanted
remote, first
erase all codes:
Press and hold the "learn" button on motor
unit until the learn indicator
light goes out
(approximately
6 seconds). All previous
codes are now erased. Reprogram
each
entry you wish to use.
iote or keyless
*3-Function
Remotes
If provided with your garage door opener, the large button
is factory programmed
to operate
it. Additional
buttons on
any Security+ e>
3-Function
remote or
_
_
compact
remote can be
programmed
to operate
other Security÷ _ garage
door openers.
35
Hide quick links:
Advertisement
Chapters
Table of Contents
Need help?
Do you have a question about the Garage Door Opener and is the answer not in the manual?
Questions and answers
Remote control will open door but does not close. Opener flashes and clicks but door does not close
The Craftsman garage door opener remote control may open the door but not close it due to an issue with the safety sensors. If the sensors are blocked, misaligned, or malfunctioning, the opener will prevent the door from closing. The steady green light on both sensors indicates they are powered, but they may still need realignment.
The flashing and clicking from the opener suggest a possible issue with the logic board or a relay. The amber indicator light blinking five times repeatedly may be an error code indicating a malfunction. If unplugging the unit and resetting it does not resolve the issue, the logic board may need to be replaced.
This answer is automatically generated
Remove control panel cover
To remove the cover from a Craftsman garage door opener, follow these steps:
1. Remove the four screws holding the cover.
2. Note that the cover may still be held by something else.
3. There are two additional screws on each side of the opener and two more on each end.
4. Remove all these screws, and the cover should come off.
This answer is automatically generated
sensors are not lit
The sensors on the Craftsman garage door opener may not be lit due to one or more of the following reasons:
1. The sensors are out of alignment.
2. There is a faulty or broken connection in the sensor wiring.
3. The sensor wires may have a short circuit, be disconnected, or have reversed polarity (black and white wires swapped).
4. One or both sensors may be faulty.
To fix the issue, check and correct the wiring, ensure proper alignment of the sensors, and replace any damaged components if needed.
This answer is automatically generated