X10 POWERHOUSE DS7000 Owner's Manual
  1. Manuals
  2. Brands
  3. X10 Manuals
  4. Security System
  5. Powerhouse DS7000
  6. Owner's manual
X10 POWERHOUSE DS7000 Owner's Manual

X10 POWERHOUSE DS7000 Owner's Manual

Supervised security system
Hide thumbs Also See for POWERHOUSE DS7000:
Table of Contents

Advertisement

Quick Links

Enlarged version
Supervised Security System
Owner's Guide
1
2
3
4
5
6
7
8
9
0
PROG
MEM
Supervised Security System DS7000
1
15
3
RECORD
Install
Run 1
13
5
Run 2
11
7
ARM
9
UNIT
A
BYPASS
O
C
M
E
K
G
I
HOUSE
AC Power
Battery Low
zones
1
2
3
4
5
6
7
8
REC/BUSY
ARMED

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the POWERHOUSE DS7000 and is the answer not in the manual?

Questions and answers

Related Manuals for X10 POWERHOUSE DS7000

Summary of Contents for X10 POWERHOUSE DS7000

  • Page 1 Supervised Security System Owner's Guide RECORD Install Run 1 Run 2 UNIT BYPASS HOUSE AC Power Battery Low zones PROG REC/BUSY ARMED Supervised Security System DS7000...

  • Page 2: Table Of Contents

    Contents READ THIS FIRST If more than one telephone or other device is connected to the same line, add up all the Introduction ....................4 RENs. If the total is more than five, the This equipment generates and uses radio telephones might not ring.

  • Page 3: Introduction

    Introduction Installation The X10 Supervised Security System is built around a Security Console with an Locating Security System components automatic dialer that calls neighbors or friends in the event of a break in. Battery powered RF Door/Window Sensors and Motion Detectors are used to trigger the alarm, with RF Handheld and Keychain Remote controls for arming and disarming.

  • Page 4: Security Console

    Installation Installation Security Console Security Remote Mounting the console PANIC PANIC The Security Console is designed to be installed free-standing on a table top or shelf. DIS- HOME A wall mounting bracket is also available. DIS- AWAY Fitting the backup battery SECURITY LIGHT Slide off the battery compartment cover and clip a 9V battery onto the battery contacts.

  • Page 5: Keychain Remote

    Installation Installation Keychain Remote Door/Window Sensor BATTERY DOOR/WINDOW SENSOR PANIC DELAY DISARM DOOR/WINDOW SENSOR Ideal location LIGHTS TEST Two windows (requires LIGHTS accessory magnetic switch pair) DOOR/WINDOW SENSOR Sliding window Registering the Keychain Remote with the Security Console Installing the Door/Window Sensor •...

  • Page 6: Motion Detector

    Installation Installation Testing the Motion Detector Motion Detector • Set the slide switch on the Motion Detector to position 1. • Press and hold the TEST button for about a second. The LED flashes twice when you release it. 90˚ •...

  • Page 7: Power Horn

    Installation Installation ™ Power Horn Remote Siren (sold separately) Lamp Module UNIT UNIT HOUSE HOUSE Power Horn Lamp Module Installing the Power Horn Installing the Lamp Module to control the security light • Set the House Code dial to the same House Code as the Security System •...

  • Page 8: Other X10 Products

    Installation Setting up the Dialer Other X10 products (sold separately) Programming Phone Numbers Note: you should program the console to call a friend, relative or neighbor who can then listen-in to your home to determine if there is a real problem. The person can then call the Police if necessary, or call you back to see if everything is fine.

  • Page 9: Using The Security System

    Using the Security System Using the Security System INSTANT Mode Console Zone Indicators Note: The Key Chain Remote always arms the system in the INSTANT mode. The console displays the status of the first eight zones. These indicators can display four 1.

  • Page 10: Battery Information

    Battery Information Battery Information Door/Window Sensors and Motion Detectors General X10 Door/Window Sensors, Motion Detectors and Security and Keychain remotes are Battery Replacement designed to operate for approximately two years when fitted with alkaline batteries. If any if the Console's zone indicators flash slowly, the Motion Detector or Door/Window Since operating conditions vary from installation to installation however, it is recom- Sensor for that zone has not reported in during the last four hours.

  • Page 11: Troubleshooting

    Troubleshooting Troubleshooting PROBLEM SOLUTION PROBLEM SOLUTION If the system does not arm. • Check that the Console's slide switch If you hear a repetitive trouble alarm Check the zone indicators. If a door or is set to RUN1 or RUN2. when you try to arm the system, and it window is open, its zone indicator is on.
  • Page 12 Troubleshooting Troubleshooting PROBLEM SOLUTION PROBLEM SOLUTION If you do not hear a beep from the You open a door or window and the With the Console in the RUN 2 mode, • Check that the system is armed. Console when you press TEST to install alarm does not trip.
  • Page 13 Troubleshooting Troubleshooting Special Notes PROBLEM SOLUTION Intercom Systems If the armed indicator is flashing. This indicates that there has been an intrusion. Also, if a zone indicator is on, Intercom systems which send voice signals over existing electrical wiring may interfere Troubleshooting this indicates which zone was violated.
  • Page 14 Warranty Notes ONE YEAR LIMITED WARRANTY X10 (USA) INC. (X10) WARRANTS ITS PRODUCTS TO BE FREE FROM DEFECTIVE MATERIAL AND WORKMANSHIP FOR A PERIOD OF ONE (1) YEAR FROM THE ORIGINAL DATE OF PURCHASE AT RETAIL. X10 AGREES TO REPAIR OR REPLACE, AT ITS SOLE DISCRETION, A DEFECTIVE X10 PRODUCT IF RETURNED TO X10 WITHIN THE WARRANTY PERIOD AND WITH PROOF OF PURCHASE.
  • Page 15 X10 (USA) INC., 91 RUCKMAN RD., CLOSTER, NJ 07624 WWW.X10.COM DS7000 -4/99DR Supervised Security System...

Table of Contents