Table of Contents
Advertisement
PART LISTmModel
No. 831.24813.0
R0809A
To locate the parts listed below, see the EXPLODED DRAWING near the end of this manual.
Key No. Qty.
Description
Key No. Qty.
Description
1
16
M4.2 x 19mm Screw
51
1
2
4
M4.2 x 25mm Tek Screw
52
1
3
1
M4.2 x 13mm Hypot Screw
53
1
4
4
1/4" x 3 1/2" Bolt
54
1
5
4
M10 x 96mm Bolt
55
1
6
4
M8 x 25mm Bolt
56
2
7
1
3/8" Star Washer
57
1
8
8
M10 Star Washer
58
1
9
4
1/4" Washer
59
2
10
4
M8 Star Washer
60
1
11
5
M4.2 x 13mm Washer Head Screw
61
1
12
11
M4.2 x 16mm Screw
62
3
13
3
M4.2 x 19mm Washer Head Screw
63
1
14
2
M8 x 35mm Screw
64
1
15
2
M8 x 90mm Screw
65
1
16
2
M 10 x 30mm Bolt
66
1
17
2
M6 x 70mm Bolt
67
1
18
1
3/8"x 1 3/4" Bolt
68
1
19
1
3/8" x 1 1/2" Bolt
69
1
20
2
3/8"x 1" Bolt
70
1
21
1
M6 x 45mm Bolt
71
1
22
7
#8 x 1/2" Screw
72
1
23
8
M5.5 x 25mm Screw
73
1
24
2
1/4" x 3/8" Bolt
74
2
25
2
3/8" x 3/4" Bolt
75
2
26
1
3/8" x 4" Bolt
76
1
27
2
M10 x 50mm Bolt
77
1
28
4
M4.2 x 13mm Screw
78
1
29
2
M6 Split Washer
79
4
30
2
M6 Washer
80
1
31
3
3/8" Jam Nut
81
4
32
2
3/8" Motor Nut
82
2
33
4
M10 Nut
83
1
34
1
6 mm Hex Key
84
2
35
2
M8 Flange Nut
85
1
36
2
3/8" Locknut
86
2
37
3
Hood Clip
87
1
38
4
Cage Nut
88
1
39
1
Left Foot Rail
89
1
40
2
Platform Cushion
90
1
41
2
Belt Guide
91
4
42
1
Magnet
92
2
43
1
Motor Belt
93
1
44
1
Drive Roller/Pulley
94
2
45
1
Walking Belt
95
8
46
1
Walking Platform
96
2
47
1
Right Foot Rail
97
2
48
1
Frame
98
1
49
1
Warning Decal
99
1
50
2
Idler Roller Bracket Plate
100
1
Left Foot
Right Foot
Motor Hood
Reed Switch
Reed Switch Clamp
Frame Spacer
Lift Frame/Roller Ground Wire
Incline Motor
Idler Roller Bracket
Drive Motor
Motor Bracket
Lift Frame Cable Tie
Lift Frame
5 mm Hex Key
Power Cord
Controller
Grommet
Reset/Off Circuit Breaker
Belly Pan
Latch Insert
Left Crosswalk Arm
Latch Pin Assembly
Left Upright
#10 x 3/4" Screw
Crosswalk Arm Insert
Right Crosswalk Arm
Upright Wire
Right Upright
Bolt Spacer
Right Upright Spacer
Base Foot
Base Cap
Left Upright Spacer
Caution Decal
Base
Wheel
Console
Console Base
Left Handrail
Right Handrail
Handrail Cap
Cable Tie
Key/Clip
Releasable Tie
8" Cable Tie
Resistance Assembly
Hand Grip
Incline Motor Wire Harness
Lift Motor Spacer
Idler Roller
22
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the crosswalk sport and is the answer not in the manual?
Questions and answers
The motor runs but the walking belt doesn't move...any way to fix??
To fix the walking belt on a ProForm Crosswalk Sport if the motor runs but the belt doesn't move, follow these steps:
1. Check the Belt Tension – Lift each side of the walking belt. It should lift 2 to 3 inches (5 to 7 cm) off the walking platform. If it's too loose, tighten it.
2. Center the Belt – Ensure the walking belt is centered on the platform.
3. Adjust the Tension – Turn the adjustment bolts at the back of the treadmill to tighten the belt gradually.
4. Test the Belt – Plug in the power cord, insert the key, and walk on the treadmill for a few minutes. If the belt still doesn’t move, repeat the adjustment process.
If the issue persists, further troubleshooting may be required.
This answer is automatically generated
does the walking belt need to be lubricated
No, the ProForm Crosswalk Sport walking belt does not need lubrication. It is already coated with a high-performance lubricant, and applying silicone spray or other substances can damage the belt and cause excessive wear.
This answer is automatically generated
The machine come on put shuts off within 5 seconds