Table of Contents
Advertisement
Quick Links
SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
PELLET STOVE
Empress
Fireplace Insert
TECHNICAL MANUAL
Contact your building or fire officials about restrictions and installation
inspection requirements in your area.
PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE
OF THIS PELLET BURNING ROOM HEATER. FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY, OR
EVEN DEATH.
50-1386
Advertisement
Table of Contents
Related Manuals for Enviro 50-1386
Summary of Contents for Enviro 50-1386
-
Page 1: Fireplace Insert
Contact your building or fire officials about restrictions and installation inspection requirements in your area. PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET BURNING ROOM HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY, OR EVEN DEATH. 50-1386... -
Page 2: Table Of Contents
Introduction...3 Rating Label Location...3 Important Safety Data...3 Safety Warnings And Recommendations...3 Automatic Safety Features...4 Installation...5 Removing Pellet Stove From Pallet...5 Dimensions...5 Clearances to Combustibles...6 Masonry Fireplace Installation...7 Positive Flue Connection without a Full Reline (USA Only)...8 Adjusting Hopper Height ...9 Installation of Cast Skirt Option...9... -
Page 3: Introduction
To prevent the possibility of a fire, ensure that the appliance is properly installed by adhering to the installation instructions. An ENVIRO dealer will be happy to assist you in obtaining information with regards to your local building codes and installation restrictions. -
Page 4: Automatic Safety Features
If this power cord should become damaged, a replacement power cord must be purchased from the manufacturer or a qualified ENVIRO dealer. Be careful that the electrical cord is not trapped under the appliance and that it is clear of any hot surfaces or sharp edges. This unit’s maximum power requirement is (4.1 Amps) 500 watts. -
Page 5: Installation
Figure 2: Dimensions of Empress Fireplace Insert. Installation ALLET ” socket to remove the " (779mm) " (710mm) " (530mm) " (383mm) (222mm) " (786mm) (757mm) 27" (686mm) Figure 1: Removing Stove From the Pallet. " " (379mm) 30" (762mm) " " (554mm) " (503mm) -
Page 6: Clearances To Combustibles
" (611mm) Figure 3: Dimensions of Empress Fireplace Insert with Optional Skirt. LEARANCES TO OMBUSTIBLES Refer to Figure 4. Side wall to center of unit 24 inches (61.0 cm) Side wall to surround 3 inches Mantel projection 12 inches (30.5 cm) Mantel to bottom of unit 36 inches (91.4 cm) Top facing to unit... -
Page 7: Masonry Fireplace Installation
Flexible or Rigid 3" Stainless Steel Liner Damper Removed or Fastened Open 12" (30.5cm) Mantle Minimum 36" (91 cm) from Bottom of stove Surround Panel Min 6" (150 mm) Floor Protection ����������� ����� If installing the Empress with a skirt the skirt must be installed before the installation. -
Page 8: Positive Flue Connection Without A Full Reline (Usa Only)
12" (30.5cm) Mantle Minimum 36" (91 cm) from Bottom of stove. Surround Panel 4. Set leveling leg to approximate Min 6" (15.2 cm) 5. Connect the Exhaust Starter Quick Floor Protection �����������... -
Page 9: Adjusting Hopper Height
DJUSTING OPPER EIGHT The back height of this unit can be set to one (1) of three (3) heights; 19 ” (503 mm), 20 mm). The hopper should be set to the maximum height that can be used in the installation. To change the height of the hopper up or down, remove the seven (7) T-20 screws, three (3) on each side and one (1) on the back. -
Page 10: Surround Panel Installation
URROUND ANEL NSTALLATION 1. Lift the cast top, it will come up and forward. 2. Install the daughter board onto the right side of the surround panel onto the two (2) studs. Fasten into place with a wingnut on each stud. 3. -
Page 11: Slider/Damper Setting
SPECIAL NOTES: Pellet quality is a major factor in how the pellet stove will operate. If the pellets have a high moisture content or ash content the fire will be less efficient and has a higher possibility of the fire building up and creating clinkers (hard ash build-up). -
Page 12: Troubleshooting
DO NOT: ● Service the stove with wet hands. The stove is an electrical appliance, which may pose a shock hazard if handled improperly. Only qualified technicians should deal with possible internal electrical failures. ● Do not remove from the firebox any screws without penetrating oil lubrication. - Page 13 Check the vacuum readings by placing the open end of the vacuum hose on a Magnahelic Gauge (readings must be above 0.07” W.C. (17.4 Pa) on low fire). üPoor quality fuel – insufficient energy in the fuel to produce enough heat to keep the stove burning or operational.
- Page 14 üSet the auger trim till the #1 and #5 lights are illuminated. b) If the stove goes out and there are partially burned pellets left in the burn pot liner, the stove has shut down due to a lack of air, exhaust temperature, or power failure.
-
Page 15: Wiring Diagram
Wiring Diagram Orange Vacuum Orange Switch Blue Combustion White Blower Brown F (49 Exhaust Temperature Sensor Brown Black White Black Ignitor Purple Convection White Blower Yellow Auger White Motor F (93 Grey High Limit Grey Temperature Sensor Connect Thermostat Here Power Cord Ground... -
Page 16: Parts List
Empress FPI Domestic Owner’s Manual - 115V Empress FPI Domestic Technical Manual - 115V Vacuum Switch - Low Preasure Parts List Part Number EC-001 EC-042 EF-001 EF-016 EF-018 EF-060 EF-156 EF4i-002 50-177 50-185 50-262 50-473 50-619 50-634 50-750 50-833 50-968 50-1346 50-1359 50-1366 50-1385 50-1386 50-1390... - Page 17 Reference Description Number Exhaust Starter Tube 3” Quick Connect Mother Board - 120V Daughter Board - 120V Slider Damper & Lever Exhaust Starter Elbow Quick Connect Exhaust Starter Gasket Daughter Board Decal Ignitor & Intake Tube Cast Brick Panel Set Inner Door Complete with Glass &...
-
Page 18: Parts Diagram - Components
Parts Diagram - Components Empress - Fireplace Insert Components October 2006... -
Page 19: Parts Diagram - Parts
Parts Diagram - Parts... -
Page 20: Warranty
Industries, our commitment to the highest level of quality and customer service is the most important thing we do. Each Enviro stove is built on a tradition of using only the finest materials and is backed by our Exclusive Lifetime Limited Warranty to the original purchaser. With Enviro, you’re not just buying a stove, you’re buying a company with years of unequalled performance and quality. - Page 21 7. Misuse includes over-firing. Over-firing this appliance can cause serious damage and will nullify the Limited Warranty. 8. The Limited Warranty will cover glass thermal breakage only and will not cover misuse of the stove glass, including but not limited to glass that is struck, has surface contaminates or has had harsh or abrasive cleaners used on it.
- Page 22 If the stove is used for commercial purposes, it is excluded from the Limited Warranty. 24. No dealer, distributor, or similar person has the authority to represent or warrant Enviro products beyond the terms contained within the Limited Warranty. Sherwood Industries Ltd. assumes no liability for such warranties or representations.
-
Page 23: Installation Data Sheet
Installation Data Sheet The following information must be recorded by the installer for warranty purposes and future reference. NAME OF OWNER: _________________________________________ ADDRESS: _________________________________________ _________________________________________ _________________________________________ PHONE:___________________________________ MODEL:___________________________________ SERIAL NUMBER:___________________________ DATE OF PURCHASE: _____________ DATE OF INSTALLATION:___________ MAGNEHELIC AT INSTALL:___________________ INSTALLER’S SIGNATURE: _________________________________________ 6782 OLDFIELD RD.
Need help?
Do you have a question about the 50-1386 and is the answer not in the manual?
Questions and answers