Antec Nine Hundred User Manual
Gaming case
Hide thumbs
Also See for Nine Hundred:
- Manuel d'utilisation (10 pages) ,
- Specifications (1 page) ,
- User manual (10 pages)
Related Manuals for Antec Nine Hundred
Summary of Contents for Antec Nine Hundred
- Page 1 Nine Hundred User’s Manual Manuel de l’utilisateur Anwenderhandbuch Manuale per l’operatore Manual del usuario...
- Page 2 Disclaimer This manual is intended only as a guide for Antec’s Computer Enclosures. For more comprehensive instructions on installing the motherboard and peripherals, please refer to the user’s manuals that come with those components.
- Page 3 Installing the Motherboard This manual is not designed to cover CPU, RAM, or expansion card installation. Please consult the motherboard manual for specific mounting instructions and troubleshooting. Before proceeding, check the manual for your CPU cooler to find out if there are steps you must do before installing the motherboard. Lay the case down so that the open side is up.
- Page 4 FireWire port to an IEEE 1394 add-on card that comes with an external-type IEEE 1394 connector, you will need a FireWire Internal Adapter. To order one, please visit Antec’s web store at http://www.antec.com/StoreFront.bok and search for part number 30031. This adapter will allow you to connect the front IEEE 1394...
- Page 5 Pin Assignment for Front Panel IEEE 1394 Connector Signal Names Signal Names TPA+ TPA– Ground Ground TPB+ TPB– +12V (Fused) +12V (Fused) Key (No Pin) Ground Connecting the Audio Ports (AC’97 and HDA) There is an Intel® standard 10-pin AC’97 connector and an Intel® 10-pin HDA (High Definition Audio) connector.
- Page 6 External 5.25” Device Installation Note: The HDD cages each occupy three consecutive drive bays, and will block installation of larger devices such as optical drives, so please plan ahead before installing your drives. Remove both side panels per the instructions in Setting Up.
- Page 7 If you intend to install one of the newest full-length graphics cards, we recommend that you install the optional support bracket. To order one, please visit Antec’s web store at http://www.antec.com/StoreFront.bok and search for part number 30115. Twist the bracket into place at the back of the installed graphic card. Then install the two included screws to secure the bracket to the drive bay.
- Page 8 High if you choose to connect the fan(s) to a fan control device or to the Fan-Only connector found on some Antec power supplies. A fan control device regulates the fan speed by varying the voltage, which may start as low as 4.5V to 5V.
- Page 9 There are two optional 120mm fan mounts—the side fan (on the left side panel) and the middle fan (at the rear end of the HDD cage). We recommend using Antec 120mm TriCool™ fans and setting the speed to Low. These two fans should be installed so that the air is blowing into the case.
- Page 10 1-800-22ANTEC customersupport@antec.com Europe +31 (0) 10 462-2060 europe.techsupport@antec.com www.antec.com © Copyright 2007 Antec, Inc. All rights reserved. All trademarks are the property of their respective owners. Reproduction in whole or in part without written permission is prohibited. Printed in China.
Need help?
Do you have a question about the Nine Hundred and is the answer not in the manual?
Questions and answers
Hi. Looking for any instructions for removing top cover to replace "Big Boy" 200 mm fan in Antec 900 ATX case. Appreciate any help
To remove the top cover and replace the "Big Boy" 200mm fan in the Antec Nine Hundred ATX case, follow these steps:
1. Unscrew the 4 screws holding the fan.
2. Unscrew the 4 screws retaining the top cover.
3. Slide the top cover towards the front of the case to release it from the 4 retaining clips.
4. Raise the top cover just enough to remove the fan.
5. Install the new fan and reassemble by reversing these steps.
It is not necessary to remove the hard drive cage or the front face.
This answer is automatically generated