Advertisement
Quick Links
Use and Care Guide
®
LiquidPropane Gas Grill with infraredCooking System
Sears Model No. 4t5.t6650900
This Grill is for Outdoor Use Only
:
i i
¸¸¸¸¸!
:L :
!_i_i!i!ii,
¸¸
•
Read and follow all Safety, Assembly,
and Use and Care instructions in this
Guide before assembling and cooking
with this grill.
•
Failure to follow all instructions in this
Use and Care Guide may lead to fire or
explosion, which could result in property
damage, personal injury or death.
•
Safety
•
Parts
•
Use and Care
•
Assembly
Assembly Questions?
Call t-800-241-7548
Tools
needed for assembly:
Adjustable wrench (not provided)
Screwdriver (not provided)
7/16" Combination wrench (not provided)
SAVETHESEINSTRUCTIONS!
Sears,
Roebuck
and Co., Hoffman
Estates,
IL 60179
©2008Sears, RoebuckandCo., All Rights Reserved
Printedin China
U.S.A.
464222209,80019045,11-18-08
Advertisement
Related Manuals for Kenmore 464222209 - Grill With 100% Infrared Cooking System
Summary of Contents for Kenmore 464222209 - Grill With 100% Infrared Cooking System
- Page 1 Use and Care Guide ® LiquidPropane Gas Grill with infraredCooking System Sears Model No. 4t5.t6650900 This Grill is for Outdoor Use Only ¸¸¸¸¸! :L : !_i_i!i!ii, ¸¸ • Safety • Parts • Use and Care • Read and follow all Safety, Assembly, •...
- Page 2 CALIFORNIA PROPOSiTiON 65 if you smell gas: 1. Combustion by-products produced when using 1. Shut off gas to the appliance. this product contain chemicals known to the State of 2. Extinguish any open flame. California to cause cancer, birth defects, and other 3.
- Page 3 Protection Agreements Congratulations on making a smart purchase. Your new Kenmore® product is designed and manufactured for years of All warranty coverage is void if this grill is ever used for dependable operation. But like all products, it may require repair commercial or rental purposes.
- Page 4 LP Tank • The LP Tank used with your grill must meet the following requirements: • Use LP Tanks only with these required measurements: 12" (30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.) capacity maximum. • NEVER store a spare LP cylinder under or near the •...
- Page 5 LP Tank Exchange Connecting Regulator To The LP Tank • Many retailers that sell grills offer you the option of replacing 1. LP tank must be properly secured onto grill. (Refer to your empty LP tank through an exchange service. Use only assembly section.) those reputable exchange companies that inspect, precision fill, 2.
- Page 6 Leak Testing Valves, Hose and Regulator 1. Turn all grill control knobs to OFF. 2. Be sure regulator is tightly connected to LP tank. 3. Completely open LP tank valve by turning OPD hand wheel counterclockwise. If you hear a rushing sound, turn gas off immediately.
- Page 7 Safety Tips ,A, Before opening LP cylinder valve, check the coupling nut for tightness. ,A, When grill is not in use, turn off all control knobs and LP cylinder valve. For Safe Use of Your Grill and to Avoid Serious ,A, Never move grill while in operation or still hot.
- Page 8 Sideburner Match Lighting 1. Turn OFF all burner control valves. 2. Open the sideburner lid. Turn controls and gas source or tank OFF when not Turn on gas at LP cylinder. in use. 3. Place lit match near burner. cAuT,o. 4.
- Page 9 cAuTioN •Stainless steel surfaces: To maintain your grill's high quality appearance, wash with mild detergent and warm soapy water and wipe dry with a soft cloth after each use. Baked-on grease deposits may require the use of an abrasive plastic cleaning pad.
- Page 10 We suggest three ways to clean the burner tubes. Use the one Storing Your Grill easiest for you. •Clean cooking grates. (A) Bend a stiff wire (a light weight coat hanger works well) •Store in dry location. into a small hook. Run the hook through each burner •When LP tank is connected to grill, store outdoors in well- tube several times.
- Page 11 Single Zone Cooking The Kenmore® Infrared grill is designed to cook just as dfciently using 1 burner or zone as it does when utilizing all burners. This method allows you the option of cooking small amounts of food without having to heat up your entire grill. In order to utilize this method simply pre-heat your grill using only the desired burner.
- Page 12 rii| alogen Light LIGHT OPERATION iNSTRUCTiONS 1. Make sure light switch on the control panel is in the "OFF" position. 2. Connect light plug to an extension cord, then put the extension cord plug into the outlet on the wall. 3.
- Page 13 Cleaning Lens 1. Prior to cleaning, make sure the light switch is in the "OFF" position and the light plug is disconnected from the power supply. 2. Do not clean the glass lens when warm. Allow to cool before cleaning. Sudden change in temperature...
- Page 14 RUBBER BUMPER, ROUND, F/ 80006625 NOT Pictured RUBBER BUMPER, 80006983 1 CASTER WRENCH 80000283 RECTANGULAR, F/LID HARDWARE PACK 80006699 1 LOGO PLATE, KENMORE 80010544 1 HARDWARE F/TOP LID 80017592 1 ASSEMBLY MANUAL, 80019045 ASSEMBLY ENGLISH 1 FRONT BRACE 80007579 1 ASSEMBLY MANUAL,...
- Page 15 C__-_!I ¸ _.-i _ 4642222O9,15...
- Page 16 Screw in the two locking casters at the rear of the bottom shelf and the two fixed casters at the front and tighten with the caster wrench provided. Fixed casterx._. LockingCaster..Bottom Attach side panels to bottom shelf using three 1/4-20x1/2"...
- Page 17 Attach light adapter to back panel using four #8-32x3/8" screws, 4ram lock washers, 4ram flat washers and #8 nuts, shown A. Place lower back panel between side panels at rear of bottom shelf. Secure lower back panel to side panels using two 1/4-20x1/2"...
- Page 18 Insert front brace under control panel and between cart side panels. Secure using two l/4-20x1W' screws, 7ram lock washers on each side. NOTE: MAKE SURE THAT THE FRONT BRACE ISMOUNTED AS iLLUSTRATED BELOW. 7ramLockwasher Qty.4 l/4-20xIVz"screw Qty.4 Remove the two screws and washers that are attached on right side of firebox front, shown A. Insert flange on right side shelf into side shelf brackets on side of firebox, shown B.
- Page 19 Attach left side lower fascia to left side upper fascia using three #10x3/8" screws, 5ram lock washers and 5ram flat washers, shown A. Remove the three screws and washers that are attached on left side of firebox front, shown B. Insert flange on left side shelf into side shelf brackets on side of firebox, shown C.
- Page 20 Attach debris collector panel to upper back panel using four #10x3/8" screws, 5ram flat washers, 5ram lock washers, and #10 nuts, shown A. On back of grill, place upper back panel between side panels and above lower back panel. Secure upper back panel, in lower holes, using one l/4-20xllA '' screw and 7ram lock washer on each side.
- Page 21 First, remove the two screws and lock washers already attached to the sideburner valve bracket. Position sideburner valve bracket beneath sideburner shelf fascia so that valve stem comes through larger center hole in fascia. Align the holes on valve bracket with left and right holes on fascia. Secure using lock washers and screws that were removed from bracket. Next, place sideburner bezel over valve stem on front side of fascia.
- Page 22 Under sideburner shelf, attach sideburner ignitor wire to electrode, shown A. Place sideburner grate onto sidebumer shelf, aligning grate legs with holes in shelf, shown B. Sideburner grate SideburnerIgnitor Wire Inside the cart left, connect the adapter wire harnesses to the light wire harnesses as shown. 22,464222209...
- Page 23 Inside of cart, insert rear shield tabs into slots next to grease tray opening on upper back panel, shown A. Attach front shield tabs(with holes) under front brace with two #8x3/8" self-tapping screws, shown B. #8x3/8"self-tappingscrew Qty.2 front tab Note:someparts omitted (w/hole) for clarity of illustration Cart _ ewer back panel...
- Page 24 Release the cap and nut from electronic ignition module. Attach electronic ignition module and heat shield to the cart left side panel with the nut, shown A. Insert AA battery into ignition module, negative (=) end first. Then put on the cap, shown B. Connect each of the wires from the main burner electrodes, and sideburner electrode into the back of the Electronic Ignition Module.
- Page 25 Put divider panels between burners, shown A. Secure divider panels to firebox front using two #8x3/8" self-tapping screws, shown B. Secure divider panels to firebox rear using two #8x3/8" self-tapping screws, shown C. #8x3/8"self-tapping screw Qty.4 ing screw 464222209,25...
- Page 26 Place Emitter plates in the firebox. Insert temperature gauge stem into the bigger hole on the black panel,shown A. Make sure the gauge is pushed in as far as it will go, then push the gauge downward until it clips into the panel, as shown in B/C.
- Page 27 Place cooking grates onto the firebox as shown. Make sure to put taller end at rear of fire box. Rear of grate Insert the two wire ends at rear of warming rack into holes in back of firebox. Front wires of warming rack rest on sides of firebox. Assembled warmingrack Warming rack...
- Page 28 LP CYLINDER IS SOLD SEPARATELY. Fill and leak check the cylinder before attaching to grill and regulator (see Use & Care section). Once cylinder has been filled and leak checked, place cylinder into hole in bottom shelf. Make sure cylinder valve is facing front of grill.
- Page 29 EMERGENCIES; if a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department. Gasleakingfrom •Damagedhose. •Turnoff gas at LP cylinderor at sourceon naturalgassystems.If cracked/cut/burned anythingis burned,replacevalve/hose/regulator. If burned, hose. discontinueuseof productuntila plumberhas investigated cause and corrections are made.
- Page 30 Troubleshooting (continued) ELECTRONIC IGNITION: Burner(s)will not light usingignitor. •No spark,no ignitionnoise. • SeeSectionI of ElectronicIgnitionSystemon the nextpage. (See ElectronicIgnition Troubleshooting a lso) •No spark,some ignitionnoise. • SeeSectionII of ElectronicIgnitionSystemon the next page. •Sparks,but not at electrodeor at full • SeeSectionIII of ElectronicIgnitionSystemon the next page. strength.
- Page 31 Troubleshooting - Electronic Ignition SECTION I Nosparksappearat ,Battery not installed •Checkbatteryorientation. •Installbattery(makesurethat "+" and"-" anyelectrodeswhen properly. connectorsare orientedcorrectly, w ith "+"end up controlknobturnedto and "-" enddown.) _" ; no noisecan be heardfrom spark •Deadbattery. •Has batterybeen used •Replacebatterywith newAA-sizealkalinebattery. module. previously? •Checkto insurethreadsare •Ignitionbuttoncap...
- Page 32 Your Home ...... !!!!!!!!!!!!!!!!!!!!!_ iiiiiiiiiiiiiiiiiiiiii' For expert troubleshooting and home solutions advice: iiiiiiiiiiiiiiiiiiiiii !!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!! iiiiiiiiii alnage ho ,e iiiiiiiiiiiiii !!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!! ...... iiiiiiiiiiiiiiiiiiiii: ......................................iiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiii For repair- in your home - of all major brand appliances, iiiiiiiiiiiiiiiiiiii iiiiiiiiiii iiiiiiiiiii lawn and garden equipment, or heating and cooling systems, iiiiiiiiiiiiiiiiiiiiii...