Cisco 7600 SIP 200 - SPA Interface Processor 200 Hardware Installation Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Wireless Router
  5. 7600 SIP 200 - SPA Interface Processor 200
  6. Hardware installation manual
Cisco 7600 SIP 200 - SPA Interface Processor 200 Hardware Installation Manual

Cisco 7600 SIP 200 - SPA Interface Processor 200 Hardware Installation Manual

7600 series sip, ssc, and spa hardware installation guide
Hide thumbs
Table of Contents

Advertisement

Quick Links

Cisco 7600 Series Router SIP , SSC, and
SPA Hardware Installation Guide
October, 2010
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
OL-5052-14

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 7600 SIP 200 - SPA Interface Processor 200 and is the answer not in the manual?

Questions and answers

Related Manuals for Cisco 7600 SIP 200 - SPA Interface Processor 200

Summary of Contents for Cisco 7600 SIP 200 - SPA Interface Processor 200

  • Page 1 Cisco 7600 Series Router SIP , SSC, and SPA Hardware Installation Guide October, 2010 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 OL-5052-14...
  • Page 2 You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures: •...

  • Page 3: Table Of Contents

    Cisco 7600 SIP-200 Memory Installation and Removal Cisco 7600 SIP-200 Default DIP Switch Settings Cisco 7600 SIP-400 Overview Cisco 7600 SIP-400 Processor Cisco 7600 SIP-400 LEDs Cisco 7600 SIP-400 Physical Specifications Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...
  • Page 4 OC-3c/STM-1 POS SPA Interface Specifications 3-15 OC-3c/STM-1 POS SPA SFP Optical Transceiver Modules and Cables 3-16 1-Port OC-12c/STM-4 ATM SPA Overview 3-17 1-Port OC-12c/STM-4 ATM SPA LEDs 3-17 Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...
  • Page 5 1-Port OC-192c/STM-64 POS/RPR VSR Optics SPA Fixed Optical Transceiver, 40-pin Connector, and Cables 3-38 4-Port and 8-Port Fast Ethernet SPA Overview 3-39 4-Port and 8-Port Fast Ethernet SPA LEDs 3-39 Cables, Connectors, and Pinouts 3-40 Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...
  • Page 6 1-Port Channelized OC-3 STM1 ATM CEoP SPA Optical Transeiver Modules and Cables 3-60 24-Port Channelized T1/E1 ATM CEoP SPA Overview 3-60 24-Port Channelized T1/E1 ATM CEoP SPA LEDs 3-61 24-Port Channelized T1/E1 ATM CEoP SPA Interface Specifications 3-61 Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...
  • Page 7 Deactivation of a SIP Configuration Example Activation of a SIP Configuration Example Deactivation of a SPA Configuration Example Activation of a SPA Configuration Example SIP Installation and Removal Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...
  • Page 8 SPA Blank Filler Plates SPA Cable-Management Brackets Troubleshooting the Installation Troubleshooting Using debug Commands Packing a SPA for Shipment Packing a SIP for Shipment Index IN-1 N D E X Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide viii OL-5052-14...
  • Page 9 This document describes the SPA interface processors (SIPs) and shared port adapters (SPAs) that are supported on the Cisco 7600 series routers. This document also describes how to install the supported SIPs and SPAs and how to troubleshoot the installation.
  • Page 10 Added STM1 Electrical SFP support for • SPA-1ChOC3-CE-ATM and SPA-1xCHSTM1/OC3 to Chapter 1, “SIP and SPA Product Overview.” 12.2 (33) SRD 1 OL-5052-10 February • Added support for 1-Port Channelized 2009 STM-4/OC-12 SPA Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...
  • Page 11 June 2007 Added support for XFP-10GZR-OC192LR. 12.2(33)SRB OL-5052-06 February Added support for the 1-Port Channelized 2006 OC-3 STM1 ATM CEoP SPA and 24-Port Channelized T1/E1 ATM CEoP SPA. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...
  • Page 12 SIP and SPA installation. Chapter 7 Troubleshooting the Installation Provides information for troubleshooting the installation of SIPs and SPAs. It also describes helpful debug commands and error messages. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...

  • Page 13: Related Documentation

    Cisco 7600 Series Ethernet Services 20G Line Card Hardware Installation Guide • An overview of the Cisco 7600 series router features, benefits, and applications can be found in the Cisco 7600 Series Internet Router Essentials document located at the following URL: http://www.cisco.com/en/US/products/hw/routers/ps368/products_quick_start09186a0080092248.html...

  • Page 14: Document Conventions

    Within the SIP and SPA software configuration guides, the term router is generally used to refer to a variety of Cisco products (for example, routers, access servers, and switches). Routers, access servers, and other networking devices that support Cisco IOS software are shown interchangeably within examples.
  • Page 15 Guidelines For information on obtaining documentation, obtaining support, providing documentation feedback, security guidelines, and also recommended aliases and general Cisco documents, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html...
  • Page 16 Preface Obtaining Documentation, Obtaining Support, and Security Guidelines Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...

  • Page 17: Sip And Spa Product Overview

    • Power Management, page 1-14 • For software details for the specific SIPs and SPAs that are supported on the Cisco 7600 series routers, refer to the companion publication, Cisco 7600 Series Router SIP, SSC, and SPA Software Configuration Guide.

  • Page 18: Spa Services Cards

    SSCs support online insertion and removal (OIR) with SPAs inserted in their subslots. SPAs also • support OIR and can be inserted or removed independently from the SSC. Cisco IOS Release 12.2(33) SRE adds support for Route Switch Processor 720 10GE to the Cisco • 7600 SSC-400.

  • Page 19: Sip, Ssc, And Spa Compatibility

    SIP, SSC, and SPA Compatibility The following tables show SIP and SPA compatibility by SPA technology area on the Cisco 7600 series router. For more information about the introduction of support for different SIPs and SPAs, refer to the “Release Note History”...
  • Page 20 You cannot use a SPA-5X1GE and two SPA-8x1FE on the same SIP-400. That would overrun the Note SIP-400 SPI port limit and the last SPA inserted would be powered down. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...
  • Page 21 SIP and SPA Compatibility Table for CEoP SPAs Product ID SIP Type Cisco 7600 Cisco 7600 Cisco 7600 Cisco 7600 SIP-200 SIP-400 SIP-600 SSC-400 1-Port Channelized OC-3 STM1 ATM SPA-1CHOC3-CE-ATM CEoP SPA Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...

  • Page 22: Modular Optics Compatibility

    SPA-24CHT1-CE-ATM CEoP SPA 2-Port Channelized T3/E3 ATM CEoP SPA-2CHT3-CE-ATM E3 support is not available on the 2-Port Channelized T3/E3 ATM CEoP SPA on SIP-400 of the Cisco Note Series Router 7600 Modular Optics Compatibility Some SPAs implement small form-factor pluggable (SFP) optical transceivers to provide network connectivity.
  • Page 23 SFP-OC3-LR2 • ONS-SC-155-EL • 1-Port OC-12c/STM-4 POS SPA SFP-OC12-MM • SFP-OC12-SR • SFP-OC12-IR1 • SFP-OC12-LR1 • SFP-OC12-LR2 • 1-Port OC-48c/STM-16 POS SPA SFP-OC48-SR • • SFP-OC48-IR1 • SFP-OC48-LR2 Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...

  • Page 24: Supported Dwdm-Xfp Modules

    Supported DWDM-XFP Modules Table 1-8 lists the pluggable DWDM-XFP modules supported on Cisco 7600-SIP400/600-10GE line cards. Note DWDM-XFP optics are only supported on the SIP600/SPA-1X10GE-L-V2 in SRB 3. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...
  • Page 25 DWDM XFP 1546.92 nm XFP 12.2(33)SRC (100 GHz ITU grid) DWDM-XFP-47.72 DWDM XFP 1547.72 nm XFP 12.2(33)SRC (100 GHz ITU grid) DWDM-XFP-48.51 DWDM XFP 1548.51 nm XFP 12.2(33)SRC (100 GHz ITU grid) Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...
  • Page 26 DWDM- XFP-60.61 DWDM XFP 1560.61 nm XFP 12.2(33)SRC (100 GHz ITU grid) Supported DWDM-SFP Modules Table 1-9 lists the pluggable DWDM-SFP modules supported on Cisco 7600-400/600-1GE line cards. Table 1-9 Supported DWDM-SFP Modules Product ID (append “=” for spares) Product Description...
  • Page 27 12.2(33)SRD (100 GHz ITU grid) DWDM-SFP-3268 DWDM SFP 1532.68 nm SFP 12.2(33)SRD (100 GHz ITU grid) DWDM-SFP-3425 DWDM SFP 1534.25 nm SFP 12.2(33)SRD (100 GHz ITU grid) Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 1-11 OL-5052-14...
  • Page 28 Cisco CWDM SFP 1610 nm; 12.2(33)SRD Gigabit Ethernet and 1G/2G FC Supported BX SFP Modules Table 1-11 lists the pluggable BX SFP modules supported on Cisco 7600-200/400/600-1GE line cards. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 1-12 OL-5052-14...
  • Page 29 GLC-BX-D 1000BASE-BX10-D SIP 400 and 12.2(33)SRD downstream bidirectional SIP 600 single fiber; with DOM GLC-BX-U 1000BASE-BX10-U upstream SIP 400 and 12.2(33)SRD bidirectional single fiber; with SIP 600 Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 1-13 OL-5052-14...

  • Page 30: Power Management

    IPSec VPN SPA 1-Port 10-Gigabit Ethernet SPA 17.4 2-Port Gigabit Ethernet SPA 12.9 5-Port Gigabit Ethernet SPA 13.1 10-Port Gigabit Ethernet SPA 4-Port and 8-Port Fast Ethernet SPA 16.2 Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 1-14 OL-5052-14...
  • Page 31 Router#%C7KPWR-SP-4-POWERDENIED:insufficient power, module in slot 3 power denied. On a Cisco 7600 series router, use the show power command on the Route Processor to determine how much power you have available in the chassis and how much is being used or reserved by line cards, supervisor engines, and fan trays.
  • Page 32 Chapter 1 SIP and SPA Product Overview Power Management Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 1-16 OL-5052-14...

  • Page 33: Overview: Cisco 7600 Series Sips

    Cisco 7600 SSC-400 Overview, page 2-12 • SIP Summary Summary descriptions of the SIPs that are supported on the Cisco 7600 series routers are shown in Table 2-1. The Description column indicates the aggregate bandwidth supported by the SIP across all subslots—not Note per SPA subslot.

  • Page 34: Checking Hardware And Software Compatibility

    Identifying Slots and Subslots for SIPs and SPAs This section describes how to specify the physical locations of a SIP and SPA on the Cisco 7600 series routers within the command-line interface (CLI) to configure or monitor those devices.
  • Page 35 Identifying Slots and Subslots for SIPs and SPAs Figure 2-1 shows an example of a SIP installed in slot 6 on a Cisco 7609 router. The Cisco 7609 router has nine vertically-oriented chassis slots, which are numbered 1 to 9 from right to left.

  • Page 36: Specifying The Sip Or Ssc Subslot Location For A Spa

    SIP in the router chassis slot, as shown in the “SIP, SSC, and SPA Product Overview” chapter of the Cisco 7600 Series Router SIP, SSC, and SPA Software Configuration Guide. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide...

  • Page 37: Cisco 7600 Sip-200 Overview

    Cisco 7600 SIP-200 installed with a vertical orientation on a Cisco 7609 router. The Cisco 7600 SIP-200 supports four subslots for the installation of SPAs. In this example, the subslot locations are vertically oriented as follows: SIP subslot 0—Top–right subslot...

  • Page 38: Cisco 7600 Sip-200 Processor

    Table 2-4 Cisco 7600 SIP-200 Physical Specifications Description Specifications Physical dimensions The SIP occupies one module slot and can be operated in Cisco 7600 series routers. Shipping weight 8 lb (3.64 kg) Operating temperature 32 to 104°F (0 to 40°C)

  • Page 39: Cisco 7600 Sip-200 Memory Options

    Cisco 7600 SIP-200 Memory Installation and Removal Figure 2-5 shows the location of the DIMMs on a Cisco 7600 SIP-200. Perform the following procedure to install and remove a DIMM: To install a DIMM, slide the DIMM into the slot. The retaining clips secure the DIMM in place.

  • Page 40: Cisco 7600 Sip-200 Default Dip Switch Settings

    IC ES C AR D 1 SW3 2 SW10 Cisco 7600 SIP-400 Overview The following sections describe the Cisco 7600 SIP-400 (Cisco part number 7600-SIP-400): Cisco 7600 SIP-400 Processor, page 2-9 • Cisco 7600 SIP-400 LEDs, page 2-9 • Cisco 7600 SIP-400 Physical Specifications, page 2-9 •...

  • Page 41: Cisco 7600 Sip-400 Processor

    Table 2-9 Cisco 7600 SIP-400 Physical Specifications Description Specifications Physical dimensions The SIP occupies one module slot and can be operated in Cisco 7600 series routers. Shipping weight 8 lb (3.64 kg) Operating temperature 32 to 104°F (0 to 40°C)

  • Page 42: Cisco 7600 Sip-600 Overview

    Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SIP-600 Overview Cisco 7600 SIP-600 Overview The following sections describe the Cisco 7600 SIP-600 (Cisco part number 7600-SIP-600): Cisco 7600 SIP-600 Processor, page 2-10 • Cisco 7600 SIP-600 LEDs, page 2-10 •...
  • Page 43 Cisco 7600 SIP-600 Physical Specifications Description Specifications Physical dimensions The SIP occupies one module slot and can be operated in Cisco 7600 series routers. The Cisco 7600-SIP-600 supports installation of only a single SPA in the first subslot. Shipping weight 8 lb (3.64 kg)

  • Page 44: Cisco 7600 Ssc-400 Overview

    Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SSC-400 Overview Cisco 7600 SSC-400 Overview The following sections describe the SPA services carrier (Cisco part number 7600-SSC-400): Cisco 7600 SSC-400 Processor, page 2-12 • Cisco 7600 SSC-400 LED, page 2-12 •...

  • Page 45: Cisco 7600 Ssc-400 Physical Specifications

    Table 2-15 Cisco 7600 SSC-400 Physical Specifications Description Specifications Physical dimensions The Cisco 7600 SSC-400 occupies one module slot and can be operated in Cisco 7600 series routers. Shipping weight 8 lb (3.64 kg) Operating temperature 32 to 104°F (0 to 40°C)
  • Page 46 Chapter 2 Overview: Cisco 7600 Series SIPs Cisco 7600 SSC-400 Overview Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 2-14 OL-5052-14...

  • Page 47: Overview: Cisco 7600 Series Router Shared Port Adapters

    C H A P T E R Overview: Cisco 7600 Series Router Shared Port Adapters This chapter describes the shared port adapters (SPAs) that are supported on the Cisco 7600 series routers and contains the following sections: Bandwidth Oversubscription, page 3-2 •...

  • Page 48: Checking Hardware And Software Compatibility

    • Checking Hardware and Software Compatibility To check the minimum software requirements of Cisco IOS software with the hardware installed on your router, Cisco maintains the Software Advisor tool on Cisco.com. This tool does not verify whether SPA interface processors (SIPs) or SPAs within a system are compatible, but it does provide the minimum Cisco IOS requirements for individual hardware modules or components.
  • Page 49 37.06 Mbps (T1) CEoP SPA 2.048 Mbps (E1) 49.15 Mbps (E1) 2-Port Channelized T3/E3 ATM CEoP 44.736 Mbps (T3) 89.47 Mbps (T3) 34.368 Mbps (E3) 68.74 Mbps (E3) Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...

  • Page 50: Cisco 7600 Sip-400 Oversubscription Guidelines

    23 SPI ports, the following error message will be posted on the console: SPI-4 port limit exceeded, SPA-5X1GE in subslot 3 has been powered down. The Cisco 7600 supports four 4-port FE SPAs or two 8-port FE SPA in SIP-400 in one shot •...

  • Page 51: 2-Port And 4-Port Channelized T3 Spa Overview

    2-Port and 4-Port Channelized T3 SPA LEDs, page 3-6 • 2-Port and 4-Port Channelized T3 SPA Interface Specifications, page 3-6 • 2-Port and 4-Port Channelized T3 SPA Cables and Connectors, page 3-7 • Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...

  • Page 52: 2-Port And 4-Port Channelized T3 Spa Leds

    2-Port and 4-Port Channelized T3 SPA Interface Specifications The framer processes incoming and outgoing T3 frames (cbit, m13/m23, and unframe). The framer operates at T3 line rates (44.2 Mbps). Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...

  • Page 53: 2-Port And 4-Port Channelized T3 Spa Cables And Connectors

    CAB-T3E3-RF-BNC-F (T3 or E3 Cable, 1.0/2.3 RF to BNC-Female, 10 feet) • CAB-T3E3-RF-OPEN (T3 or E3 Cable, 1.0/2.3 RF to BNC-Open end, 10 feet) • The Cisco cable part numbers are 72-4124-01 (with Male BNC end) and 72-4131-01 (with Female BNC Note end). Figure 3-1...

  • Page 54: 2-Port And 4-Port Clear Channel T3/E3 Spa Leds

    High-Level Data Link Control [HDLC]), and is mapped to T3 and E3 frames. The encapsulations add transport overhead to the packet of data frames before transporting, and are stripped when a packet is transported to the far end. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...

  • Page 55: 2-Port And 4-Port Clear Channel T3/E3 Spa Cables And Connectors

    CAB-T3E3-RF-BNC-F (T3 or E3 Cable, 1.0/2.3 RF to BNC-Female, 10 feet) • CAB-T3E3-RF-OPEN (T3 or E3 Cable, 1.0/2.3 RF to BNC-Open end, 10 feet) • The Cisco cable part numbers are 72-4124-01 (with male BNC end) and 72-4131-01 (with female BNC Note end). Figure 3-2...

  • Page 56: 8-Port Channelized T1/E1 Spa Interface Specifications

    Shielded twisted pair (STP) T1/E1 cables must be used to comply with EN55022/CISPR22 Class A emissions requirements. For revisions 73-8358-05 through 73-8358-08 Shielded Twisted pair (STP) T1/E1 cables must be used to comply with FCC Class A emissions requirements. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-10 OL-5052-14...

  • Page 57: 8-Port Channelized T1/E1 Spa Cables, Connectors, And Pinouts

    1-Port Channelized STM-1/OC-3 SPA LEDs The 1-Port Channelized STM-1/OC-3 SPA has two types of LEDs: an A/L LED for each port and a STATUS LED, as shown in Figure 3-5. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-11 OL-5052-14...

  • Page 58: 1-Port Channelized Stm-1/Oc-3 Spa Interface Specifications

    SONET/SDH, and RFC 1662, PPP in HDLC-like Framing. The 1-Port Channelized STM-1/OC-3 SPA also provides support for SNMP v1 agent (RFC 1155–1157), and Management Information Base (MIB) II (RFC 1213). Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-12 OL-5052-14...

  • Page 59: 1-Port Channelized Stm-1/Oc-3 Spa Cables And Connectors

    Long-range SFP optical transceiver modules (for long-reach configurations) cannot be connected back-to-back without using an attenuator between the two of them. Figure 3-7 LC Type Cables Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-13 OL-5052-14...
  • Page 60 Port is enabled by software, loopback is on. STATUS SPA power is off. Green SPA is ready and operational. Amber SPA power is on and good, and SPA is being configured. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-14 OL-5052-14...
  • Page 61 SNMP v1 agent (RFC 1155–1157), and Management Information Base (MIB) II (RFC 1213). For Cisco IOS XR Software Release 3.8.0, the 1-Port Channelized STM-4/OC-12 SPA supports Frame Note Relay Fragmentation (FRF.12) to achieve fragmentation of data packets and interleaving of voice packets.

  • Page 62: 2-Port And 4-Port Oc-3C/Stm-1 Atm Spa Overview

    2-Port and 4-Port OC-3c/STM-1 ATM SPA LEDs, page 3-17 • 2-Port and 4-Port OC-3c/STM-1 ATM SPA Interface Specifications, page 3-17 • 2-Port and 4-Port OC-3c/STM-1 ATM SPA Cables and Connectors, page 3-18 • Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-16 OL-5052-14...

  • Page 63: 2-Port And 4-Port Oc-3C/Stm-1 Atm Spa Leds

    OC-3c/STM-1 ATM SPA provides up to four 155-Mbps OC-3 network interfaces for all supported platforms. Each SPA port accepts an SFP module with a duplex LC-type receptacle that allows connection to single-mode or multimode optical fiber. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-17 OL-5052-14...

  • Page 64: 2-Port And 4-Port Oc-3C/Stm-1 Atm Spa Cables And Connectors

    Version 2 LEDs, page 3-19 1-Port Clear Channel OC-3, 3-Port Clear Channel OC-3, and 1-Port Clear Channel OC-12 ATM SPA • Version 2 Interface Specifications, page 3-20 Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-18 OL-5052-14...
  • Page 65 Port is enabled by software, and loopback is on. STATUS SPA power is off. Amber SPA power is on and good, and SPA is being configured. Green SPA is ready and operational. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-19 OL-5052-14...
  • Page 66 OC-3-equipped routers back-to-back. Long-range SFP optical transceiver modules (for long-reach configurations) cannot be connected back-to-back without using an attenuator between the modules. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-20 OL-5052-14...

  • Page 67: 2-Port And 4-Port Oc-3C/Stm-1 Pos Spa Overview

    LEDs on a 4-Port OC-3c/STM-1 POS SPA. Figure 3-16 4-Port OC-3c/STM-1 POS SPA Faceplate C/A (Carrier/Alarm) LED STATUS LED A/L (Active Loopback) LED Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-21 OL-5052-14...

  • Page 68: Oc-3C/Stm-1 Pos Spa Interface Specifications

    OC-3c/STM-1 POS SPA SFP Optical Transceiver Modules and Cables The POS SPA uses a small form-factor pluggable (SFP) optical transceiver module installed in each port for SONET and SDH single-mode and multimode optical fiber connection. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-22 OL-5052-14...

  • Page 69: 1-Port Oc-12C/Stm-4 Atm Spa Overview

    1-Port Channelized OC-12/STM-4 SPA LEDs, page 3-24 • 1-Port Channelized OC-12/STM-4 SPA Interface Specifications, page 3-24 • 1-Port Channelized OC-12/STM-4 SPA Cables and Connectors, page 3-25 • Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-23 OL-5052-14...
  • Page 70 OC-12/STM-4 line rates (622.08 Mbps), and supports channelization from OC-12 down to DS0 line rates. Packet data is transported with a user-configured encapsulation (such as Point-to-Point Protocol [PPP]) and is mapped into the STS-12/STM-4 frame. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-24 OL-5052-14...
  • Page 71 II (RFC 1213). Note For Cisco IOS XR Software Release 3.8.0, the 1-Port Channelized STM-4/OC-12 SPA supports Frame Relay Fragmentation (FRF.12) to achieve fragmentation of data packets and interleaving of voice packets. FRF.12 provides a method to fragment low-priority packets and interleave high-priority packets in between the low-priority fragments to provide less delay or jitter for high-priority traffic like voice and video.
  • Page 72 Long-range SFP optical transceiver modules (for long-reach configurations) cannot be connected back-to-back without using an attenuator between the two of them. Figure 3-21 LC Type Cables Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-26 OL-5052-14...

  • Page 73: 1-Port Oc-12C/Stm-4 Atm Spa Leds

    Port is enabled by software, and there is at least one alarm. Port is not enabled by software. Green Port is enabled by software, loopback is off. Amber Port is enabled by software, loopback is on. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-27 OL-5052-14...

  • Page 74: 1-Port Oc-12C/Stm-4 Pos Spa Interface Specifications

    SONET and SDH single-mode and multimode optical fiber connection (see Figure 3-23). Cisco Systems qualifies the optics that are approved for use with its SPAs. The 1-Port OC-12c/STM-4 POS SPA supports the following types of optical transceiver modules: •...
  • Page 75 Long-range SFP optical transceiver modules (for long-reach configurations) cannot be connected back-to-back without using an attenuator between the two of them. Figure 3-24 LC-Type Cable Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-29 OL-5052-14...

  • Page 76: 1-Port Oc-48C/Stm-16 Atm Spa Overview

    Port is enabled by software, and there is at least one alarm. STATUS SPA power is off. Amber SPA power is on and good, and SPA is being configured. Green SPA is ready and operational. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-30 OL-5052-14...

  • Page 77: 1-Port Oc-48C/Stm-16 Atm Spa Interface Specifications

    The 1-Port OC-48c/STM-16 POS SPA is a single-height SPA that is installed in a SIP subslot. The 1-Port OC-48c/STM-16 POS SPA provides RPR over SONET (IEEE 802.17), SRP over SONET (Cisco Proprietary), and Packet over SONET (POS) network connectivity with a bandwidth of 9.95 Gbps.

  • Page 78: 1-Port Oc-48C/Stm-16 Pos Spa Leds

    Port is not enabled by software. Green Port is enabled by software, loopback is off. Amber Port is enabled by software, loopback is on. CARRIER Port is not enabled by software. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-32 OL-5052-14...

  • Page 79: 1-Port Oc-48C/Stm-16 Pos Spa Interface Specifications

    10/125 microns) to connect your router to a network. Figure 3-28 shows the cable type for use with the XFP optical transceiver module on the 1-Port OC-48c/STM-16 POS SPA. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-33 OL-5052-14...

  • Page 80: 2-Port And 4-Port Oc-48C/Stm-16 Pos Spa

    Figure 3-29. Figure 3-29 2-Port OC-48c/STM-16 POS SPA Faceplate SPA-2XOC48-POS/RPR PTH (Pass Through) LED ACT (Active Loopback) LED PRT (Protect) LED STATUS LED CAR (Carrier Alarm) LED Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-34 OL-5052-14...

  • Page 81: 2-Port And 4-Port Oc-48C/Stm-16 Pos Spa Interface Specifications

    IP-aware optical transport, and simplified network operations. The Spatial Reuse Protocol (SRP) is a MAC-layer protocol developed by Cisco and is used in conjunction with Cisco DPT products, which utilizes a pair of counter-rotating rings in an optimum fashion to provide improved bandwidth utilization over an equivalent SONET network.

  • Page 82: Port And 4-Port Oc-48C/Stm-16 Pos Spa Cables, Optical Transceiver Modules, And Connectors

    OC-48 IR-1: –5 to 0 dBm OC-48 LR-2: –2 to +3 dBm Receiver sensitivity (maximum) OC-48 SR: –18 dBm OC-48 IR-1: –18 dBm OC-48 LR-2: –28 dBm Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-36 OL-5052-14...
  • Page 83 Figure 3-31 SPA Mate Cables Long length RPR mate cable for single port Short length RPR mate cable for single port RPR SPAs (CBL-RPR-OC192-L) RPR SPAs (CAB-RPR-OC192-S) Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-37 OL-5052-14...

  • Page 84: 1-Port Oc-192C/Stm-64 Pos/Rpr Spa Overview

    STATUS LED The WRAP, PASSTHRU, and MATESYNC LEDs apply to the SPA in RPR/SRP mode only. In Note Cisco IOS Release 12.0(31)S, RPR/SRP mode is not supported. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-38 OL-5052-14...

  • Page 85: 1-Port Oc-192C/Stm-64 Pos/Rpr Spa Interface Specifications

    RFC 1155, Structure and Identification of Management Information for TCP/IP-Based Internets • RFC 1156, Management Information Base for Network Management of TCP/IP-Based Internets • RFC 1157, Simple Network Management Protocol (SNMP) • Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-39 OL-5052-14...

  • Page 86: Mate Interface Cables

    (TX), for SONET and SDH connection to the network. In Cisco IOS Release 12.0(31)S, only long-reach (LR) optics are supported. Cisco Systems qualifies the optics that are approved for use with its SPAs. As of Cisco IOS Release 12.0(31)S Cisco IOS XR Software Release 3.2, the XFP-10GLR-OC192SR and the XFP-10GER-OC192IR are the only optical transceiver modules qualified for use.

  • Page 87: 1-Port Oc-192C/Stm-64 Pos/Rpr Xfp Spa Overview

    1-Port OC-192c/STM-64 POS/RPR XFP SPA LEDs, page 3-42 • 1-Port OC-192c/STM-64 POS/RPR XFP SPA Interface Specifications, page 3-43 • 1-Port OC-192c/STM-64 POS/RPR XFP SPA Optical Transceiver Modules, Connectors, and • Cables, page 3-43 Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-41 OL-5052-14...
  • Page 88 Amber Port is enabled by software, and there is at least one alarm (LOS, LOF, RDI, and so on). Blinking SRP mode mismatch alarm is indicated. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-42 OL-5052-14...

  • Page 89: 1-Port Oc-192C/Stm-64 Pos/Rpr Xfp Spa Interface Specifications

    Single-mode very-long reach XFP module—XFP-10GZR-OC192LR • Cisco Systems qualifies the optics that are approved for use with its SPAs. As of, the above-listed XFPs are the only optical transceiver modules qualified for use. Use a single-mode optical fiber that has a modal-field diameter of 8.7 ±0.5 microns (nominal diameter is approximately 10/125 microns) to connect your router to a network.

  • Page 90: Oc-192 Module Connections

    OC-192 SR-1: –1 dBm OC-192 IR-2: +2 dBm OC-192 LR-2: –7.0 dBm Maximum Receiver Power Damage OC-192 SR-1: +5 dBm OC-192 IR-2: +5 dBm OC-192 LR-2: +5 dBm Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-44 OL-5052-14...

  • Page 91: Mate Interface Cables

    Note mode. Support for the RPR feature is dependent on the platform software release feature content. Verify support for the RPR feature support via SPA datasheets or by contacting your Cisco representative. 1-Port OC-192c/STM-64 POS/RPR VSR Optics SPA Overview The 1-Port OC-192c/STM-64 POS/RPR VSR Optics SPA is a double-height SPA that is installed in a SIP subslot.
  • Page 92 Color State Meaning WRAP Port is not in wrap mode. Green Port is in wrap mode somewhere on the ring. Amber Port is in wrap mode locally. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-46 OL-5052-14...

  • Page 93: 1-Port Oc-192C/Stm-64 Pos/Rpr Vsr Optics Spa Interface Specifications

    • RFC 2615, PPP over SONET/SDH • For information on SNMP MIB support, see “Implementing SNMP on Cisco IOS XR Software” in Cisco IOS XR System Management Configuration Guide. 1-Port OC-192c/STM-64 POS/RPR VSR Optics SPA Fixed Optical Transceiver, Connector, and Cables The 1-Port OC-192c/STM-64 POS/RPR VSR Optics SPA uses fixed optical transceivers, one for receive (RX) and one for transmit (TX), for SONET and SDH connection to the network.
  • Page 94 This assumes that the chassis is mounted vertically. Figure 3-34 shows the mate cables used to connect the SPAs. Figure 3-40 SPA Mate Cables Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-48 OL-5052-14...

  • Page 95: 4-Port And 8-Port Fast Ethernet Spa Overview

    1. In this case, port number refers to the numbered LEDs on the 8-Port FastEthernet SPA (0, 1, 2, 3, 4, 5, 6 or 7). Each LED number on the 8-Port FastEthernet SPA references a port on the SPA. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-49...

  • Page 96: Cables, Connectors, And Pinouts

    The interface connectors on the 4-Port and 8-Port Fast Ethernet SPA are four or eight individual RJ-45 receptacles. You can use all interface connectors simultaneously. Each connection supports IEEE 802.3 and Ethernet 10/100BASE-T interfaces compliant with appropriate standards. Cisco Systems does not supply Category 5 unshielded twisted-pair (UTP) RJ-45 cables; these cables are available commercially.

  • Page 97: 1-Port 10-Gigabit Ethernet Spa Overview

    Status LED as shown in Figure 3-45. Figure 3-45 1-Port 10-Gigabit Ethernet SPA Faceplate SPA-1X10GE-L-V2 Active/Link LED STATUS LED The 1-Port 10-Gigabit Ethernet SPA LEDs are described in Table 3-25. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-51 OL-5052-14...

  • Page 98: 1-Port 10-Gigabit Ethernet Spa Cables And Connectors

    UPC connectors are supported. Patch cords with APC connectors are not supported. Cisco Multirate 10GE XFP modules do not support Digital Optical Monitoring (DOM). The operating temperature range for the XFP modules is 0 to 70°C (32 to 158°F); storage temperature range is -40°C to +85°C (-40°F to +185°F).

  • Page 99: Xfp Port Cabling Specifications

    3. Links longer than 30 km are considered engineered links. XFP Optical Transmit and Receive Specifications Table 3-27 provides XFP optical transmit and receive specifications. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-53 OL-5052-14...

  • Page 100: Xfp Module Ordering Information

    2-Port Gigabit Ethernet SPA Overview The following sections describe the 2-Port Gigabit Ethernet SPA: • 2-Port Gigabit Ethernet SPA LEDs, page 3-55 SFP Module Cabling and Connection Equipment, page 3-57 • Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-54 OL-5052-14...

  • Page 101: 2-Port Gigabit Ethernet Spa Leds

    An SFP check is run every time an SFP module is inserted into the 2-Port Gigabit Ethernet SPA and only SFP modules that pass this check will be usable by the 2-Port Gigabit Ethernet SPA. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-55...
  • Page 102 SFP-GE-T: –40 to 85 degrees C Supply Voltage range SFP-GE-S: 3.1 to 3.5 V SFP-GE-L: 3.1 to 3.5 V SFP-GE-Z: 3.1 to 3.5 V SFP-GE-T: 3.1 to 3.5 V Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-56 OL-5052-14...

  • Page 103: Sfp Module Cabling And Connection Equipment

    Table 3-32 provides cabling specifications for the SFP modules that can be installed on the 2-Port Gigabit Ethernet SPA. Note that all SFP ports have LC-type connectors. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-57 OL-5052-14...
  • Page 104 2-Port Gigabit Synchronous Ethernet SPA LEDs, page 3-59 • 2-Port Gigabit Synchronous Ethernet SPA Interface Specifications, page 3-59 • 2-Port Gigabit Synchronous Ethernet SPA Cables and Connectors, page 3-61 • Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-58 OL-5052-14...
  • Page 105 Synchronous Ethernet is a layer 1 technology which delivers a very accurate frequency reference, but it doesn't address time synchronization. IEEE1588v2 defines a Precision Time Protocol (PTP),which distributes accurate timing information (both clock frequency and time of day) over packet networks. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-59 OL-5052-14...

  • Page 106: Power Supply

    ITU-T G.8262 (OPTIONS 1 AND 2) for platform timing support and performance. • • IETF TICTOC telecom profile support for performance. • ITU-T G.8261, G.8262, G.823, G.824, G.825, O.171, and O.172 for clock jitter and wander specifications. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-60 OL-5052-14...

  • Page 107: 5-Port Gigabit Ethernet Spa Overview

    SFP-GE-S Modules, page 3-64 • SFP-GE-L Modules, page 3-64 • SFP-GE-Z Modules, page 3-64 • SFP-GE-T Modules, page 3-65 • SFP Module Cabling and Connection Equipment, page 3-65 • Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-61 OL-5052-14...

  • Page 108: 5-Port Gigabit Ethernet Spa Leds

    The small form-factor pluggable (SFP) module is an input/output (I/O) device that plugs into the Gigabit Ethernet optical slots on the 5-Port Gigabit Ethernet SPA, linking the port with a 1000BASE-X fiber-optic network. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-62 OL-5052-14...
  • Page 109 SFP-GE-T: 328 ft. (100 m) Operating temperature range SFP-GE-S:-20 to 90 degrees C SFP-GE-L:-40 to 85 degrees C SFP-GE-Z: 0 to 85 degrees C SFP-GE-T: 0 to 70 degrees C Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-63 OL-5052-14...

  • Page 110: Sfp-Ge-S Modules

    1000BASE-ZX module at each end of the link whenever the fiber-optic cable span is equal to or greater than 15.5 miles (25 km) but less than 31 miles (50 km). Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-64...

  • Page 111: Sfp-Ge-T Modules

    We do not recommend using the SFP-GE-L and MMF with no patch cord for very short link distance (tens of meters). The result could be an elevated bit error rate (BER). 3. Dispersion-shifted single-mode fiber-optic cable. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-65 OL-5052-14...
  • Page 112 (including connectors and splices) is less than or equal to 21.5 dB. The optical loss measurement must be performed with a 1550-nm light source. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-66 OL-5052-14...

  • Page 113: 10-Port Gigabit Ethernet Spa Overview

    The port is enabled and the link is down. STATUS SPA power is off. Amber SPA power is on and good, and SPA is being configured. Green SPA is ready and operational. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-67 OL-5052-14...

  • Page 114: 10-Port Gigabit Ethernet Spa Cables, Connectors, And Pinouts

    Category 5 copper wire Table 3-41 SFP Module Specifications Specification Description Connectors LC-type connector Wavelength SFP-GE-S: 830-860 nm SFP-GE-L: 1270-1360 nm SFP-GE-Z: 1540-1570 nm SFP-GE-T: N/A Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-68 OL-5052-14...

  • Page 115: Sfp-Ge-S Modules

    The 1000BASE-ZX module is intended to be used as a Physical Medium Dependent (PMD) component for Gigabit Ethernet interfaces found on various switch and router products. It operates at a signaling rate of 1250 Mbaud, transmitting and receiving 8B/10B encoded data. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-69 OL-5052-14...

  • Page 116: Sfp-Ge-T Modules

    6.2 miles (10 km) SFP-GE-Z 1550 9/10 — 49.7 miles (80 km) — 62.1 miles (100 km) SFP-GE-T Copper 328 ft. (100 m) 1. Multimode fiber (MMF) only. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-70 OL-5052-14...

  • Page 117: Ipsec Vpn Spa Overview

    STATUS LED The IPSec VPN SPA LED is described in Table 3-43. Table 3-43 IPSec VPN SPA LED LED Label Color State Meaning STATUS SPA power is off. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-71 OL-5052-14...

  • Page 118: 1-Port Channelized Oc-3 Stm1 Atm Ceop Spa Overview

    SPA is on and good, and the SPA is being configured. Green SPA is ready and operational. The Cisco 12000 SIP-401, Cisco 12000 SIP-501, and Cisco 12000 SIP-601 do not support the IPSec Caution VPN SPA (SPA-IPSEC-2G). Installing a IPSec VPN SPA in these carrier cards could damage the guide rails.

  • Page 119: 1-Port Channelized Oc-3 Stm1 Atm Ceop Spa Interface Specifications

    1-Port Channelized OC-3 STM1 ATM CEoP SPA Optical Transeiver Modules and Cables Cisco Systems qualifies the optics that are approved for use with its SPAs. The 1-Port Channelized OC-3 STM1 ATM CEoP SPA supports the following types of optical transceiver modules: Multimode (MM) SFP module—SFP-OC3-MM...

  • Page 120: 24-Port Channelized T1/E1 Atm Ceop Spa Leds

    SPA when the cable is installed. 24-Port Channelized T1/E1 ATM CEoP SPA Cables and Connectors The 24-Port Channelized T1/E1 ATM CEoP SPA requires a Cisco cable (part number CABLE-24T1E1J1), which is shown in the following figure. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide...

  • Page 121: Cable Installation

    The following table shows the cable pinouts for the cable (part number CABLE-24T1E1J1) that is installed between the 24-Port Channelized T1/E1 ATM CEoP SPA and the rear of the patch panel. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-75...
  • Page 122 Line 9 TX Tip Not connected TX Ring RX Tip Not connected RX Ring Line 10 TX Tip Not connected TX Ring RX Tip Not connected RX Ring Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-76 OL-5052-14...
  • Page 123 Line 19 TX Tip Not connected TX Ring RX Tip Not connected RX Ring Line 20 TX Tip Not connected TX Ring RX Tip Not connected RX Ring Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-77 OL-5052-14...

  • Page 124: Rj-45 Cable Pinouts

    If both CEoP SPAs are connected to their patch panels in the same manner (TX to Transmit and RX to Receive, or TX to Receive and RX to Transmit), use a T1 cross-over cable to connect the patch panels to each other. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-78 OL-5052-14...

  • Page 125: 24-Port Channelized T1/E1 Atm Ceop Spa Patch Panel

    800-880-7674 (toll free in the U.S.A.) • 828-298-2260 (outside the U.S.A.) • ciscoinfo@smpdata.com (email) • For product support for the patch panel, contact Cisco Engineering Support at SMP Data Communications: 800-880-7674 (toll free in the U.S.A.) • 828-298-2260 (outside the U.S.A.) • • ciscoeng@smpdata.com...
  • Page 126 Port is enabled by software, loopback is on. STATUS SPA power is off. Amber SPA power is on and good, and SPA is being configured. Green SPA is ready and operational. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-80 OL-5052-14...

  • Page 127: 2-Port Channelized T3/E3 Atm Ceop Spa Interface Specifications

    The framer operates at T3 or E3 line rates (44.736 or 34.368 Mbps) depending on the mode in which it is configured. For Cisco IOS Release 12.2(33)SRC, the 2-Port Channelized T3/E3 ATM CEoP SPA supports T3 ATM Note only.
  • Page 128 Chapter 3 Overview: Cisco 7600 Series Router Shared Port Adapters 2-Port Channelized T3/E3 ATM CEoP SPA Overview Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-82 OL-5052-14...

  • Page 129: Preparing To Install A Sip Or A Shared Port Adapter

    Torque screwdriver with range from 8 to 12 inch-pounds (90 to 135 Newton-centimeters) Safety Guidelines This section provides safety guidelines that you should follow when working with any equipment that connects to electrical power or telephone wiring. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...

  • Page 130: Safety Warnings

    Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla. SÄILYTÄ NÄMÄ OHJEET Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...
  • Page 131 Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo. GUARDE ESTAS INSTRUÇÕES Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...
  • Page 132 Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. SPARA DESSA ANVISNINGAR Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...
  • Page 133 Chapter 4 Preparing to Install a SIP or a Shared Port Adapter Safety Guidelines Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...

  • Page 134: Electrical Equipment Guidelines

    Chapter 4 Preparing to Install a SIP or a Shared Port Adapter Safety Guidelines Electrical Equipment Guidelines Follow these basic guidelines when working with any electrical equipment: Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...

  • Page 135: Telephone Wiring Guidelines

    Place a removed board component-side-up on an antistatic surface or in a static shielding container. • If you plan to return the component to the factory, immediately place it in a static shielding container. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...

  • Page 136: Laser/Led Safety

    Blicken Sie weder mit bloßem Auge noch mit optischen Instrumenten direkt in Laserstrahlen. Avvertenza Le fibre ottiche ed i relativi connettori possono emettere radiazioni laser. I fasci di luce non devono mai essere osservati direttamente o attraverso strumenti ottici. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...
  • Page 137 ópticos. Advarsel Usynlig laserstråling kan forekomme fra brugte fibre eller stik. Stir ikke ind i stråler eller direkte med optiske instrumenter. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...
  • Page 138 Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into Warning beams or view directly with optical instruments. Statement 1051 Class 1 LED product. Statement 1027 Warning Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 4-10 OL-5052-14...

  • Page 139: Installing And Removing A Sip

    C H A P T E R Installing and Removing a SIP This chapter describes how to install or remove SIPs on the Cisco 7600 series routers. This chapter contains the following sections: Handling SIPs, page 5-1 • Online Insertion and Removal, page 5-2 •...

  • Page 140: Online Insertion And Removal

    Preparing for Online Removal of a SIP or SSC The Cisco 7600 series router supports OIR of the SIP and the SSC. To do this, you can power down a SIP (which automatically deactivates any installed SPAs) and remove the SIP with the SPAs still intact.

  • Page 141: Deactivating A Sip Or Ssc

    For more information about the recommended procedures for physical removal of the SIP, refer to the Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide. Deactivating a SIP or SSC To deactivate a SIP or SSC and its installed SPAs prior to removal of the SIP, use the following command...

  • Page 142: Preparing For Online Removal Of A Spa

    The interface configuration is retained (recalled) if a SIP or SPA is removed and then replaced with one of the same type. This is not the case if you replace a Cisco 7600 SIP-200 with a Cisco 7600 SIP-400 or vice versa.

  • Page 143: Deactivating A Spa

    Although graceful deactivation of a SPA is preferred using the hw-module subslot shutdown command, the Cisco 7600 series router does support removal of the SPA without deactivating it first. Before deactivating a SPA, ensure that the SIP is seated securely into the slot before pulling out the SPA itself.

  • Page 144: Verifying Deactivation And Activation Of A Spa

    • Activation of a SIP Configuration Example, page 5-7 • Deactivation of a SPA Configuration Example, page 5-7 • Activation of a SPA Configuration Example, page 5-7 • Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...

  • Page 145: Deactivation Of A Sip Configuration Example

    The following example activates the SPA that is installed in slot 2 of the router and all of its interfaces. Router# configure terminal Router(config)# no hw-module subslot 2/0 shutdown Router# Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...

  • Page 146: Sip Installation And Removal

    To ensure compliance with electromagnetic interference (EMI) approvals by providing a tight Note EMI-preventive seal for the Cisco 7600 series routers, we recommend that you first install SIPs in the slots closest to the supervisor engine slots, and then work out to the slots furthest from the supervisor engine slots.
  • Page 147 Chapter 5 Installing and Removing a SIP SIP Installation and Removal Figure 5-2 illustrates how to install and remove a SIP in a Cisco 7600 series router. Figure 5-2 SIP Installation and Removal OSM-4OC1 2 POS-SI 76 00 -SI P-6 00...
  • Page 148 Chapter 5 Installing and Removing a SIP SIP Installation and Removal Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 5-10 OL-5052-14...

  • Page 149: Installing And Removing A Shared Port Adapter

    C H A P T E R Installing and Removing a Shared Port Adapter This chapter describes how to install or remove SPAs on the Cisco 7600 series routers. This chapter contains the following sections: Handling SPAs, page 6-1 •...

  • Page 150: Spa Installation And Removal

    SPA Installation and Removal 76 00 -S IP -40 0 SP A IN TE RF AC PR OC ES SO R VP A- OC 19 2 PO S- SR Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...

  • Page 151: Installing A Spa In A Sip

    SPA when removing the SIP). Online Insertion and Removal Cisco 7600 series router SIPs and SPAs support online insertion and removal (OIR). SPAs can be inserted or removed independently from the SIP. OIR of a SIP with installed SPAs is also supported.

  • Page 152: Checking The Installation

    STATUS LEDs will illuminate amber, turning to green when the SPAs become active. When the SIP and SPA STATUS LEDs are green, all associated interfaces are configurable. • Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...

  • Page 153: Using Show Commands To Verify Sip And Spa Status

    Installing and Removing a Shared Port Adapter Checking the Installation Refer to the Cisco 7600 Series Router SIP, SSC, and SPA Software Configuration Guide for configuration instructions. If a SIP or SPA is replaced with a module of the same type (as in an OIR or hardware swap), the •...

  • Page 154: Using Show Commands To Display Spa Information

    SPAs. If you plan to install a new SPA in a subslot that is not in use, you must first remove the SPA blank filler plate. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...

  • Page 155: Spa Cable-Management Brackets

    To remove the cable-management clip, depress the button on the clip and pull it out. Step 3 Note Blank filler plugs are provided if no cable-management clips are installed. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...
  • Page 156 Chapter 6 Installing and Removing a Shared Port Adapter SPA Cable-Management Brackets Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...

  • Page 157: Troubleshooting The Installation

    C H A P T E R Troubleshooting the Installation This chapter describes how to troubleshoot the installation of SIPs and SPAs on the Cisco 7600 series routers. This chapter contains the following sections: Troubleshooting, page 7-1 • Troubleshooting Line Card Power Issues, page 7-3 •...
  • Page 158 FPD failure or that the FPD package file is not present. For more information about performing FPD upgrades, refer to the “Upgrading Field-Programmable Devices” chapter in the Cisco 7600 Series Router SIP, SSC, and SPA Software Configuration Guide. SIP Is Deactivated Possible Problem...

  • Page 159: Troubleshooting The Installation

    (ES20 and ES+ cards) can be inserted only in 9 to13 slots of 7613 chassis. Miscellaneous Line Card Issues Table 7-2 provides solutions for troubleshooting line card issues. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...
  • Page 160 But if none of the above reasons match the failure of the line card, it could a bad hardware issue. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...

  • Page 161: Troubleshooting The Installation

    SCP keepalive timer and debug LC issues. To prevent the LC from being power cycled and losing its information, ensure that you disable the SCP keepalives for some time. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...
  • Page 162 If a bay crashes, collect the stack trace to identify problem. Troubleshooting Line Card States Table 7-3 provides solutions for troubleshooting line card issues. Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide OL-5052-14...

  • Page 163: Using Debug Commands

    For this reason, use debug commands only to troubleshoot specific problems or during troubleshooting sessions with Cisco technical support staff. Moreover, it is best to use debug commands during periods of lower network traffic and fewer users. Debugging during these periods decreases the likelihood that increased debug command processing overhead will affect system use.

  • Page 164: Packing A Spa For Shipment

    Use Cisco Systems original packaging for the shipment of all SPAs and cable-management brackets. Caution Failure to properly use Cisco Systems packaging can result in damage or loss of product. During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly Warning touch the backplane with your hand or any metal tool, or you could shock yourself.
  • Page 165 Troubleshooting the Installation Packing a SIP for Shipment • Two foam packing cushions Use Cisco Systems original packaging for the shipment of all SIPs. Failure to properly use Cisco Caution Systems packaging can result in damage or loss of product. Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card.
  • Page 166 Chapter 7 Troubleshooting the Installation Packing a SIP for Shipment Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 7-10 OL-5052-14...

  • Page 167: N D E X

    3-81 Cable management brackets LEDs 3-79, 3-80 cables 2-Port Gigabit Ethernet SPA LC-type Cables and Connectors 3-55 (figure) 3-34, 3-44 LEDs 3-55 LC-type (figure) 3-29 Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide IN-1 OL-5052-14...
  • Page 168 5-6, 5-7 GBIC-SX no power enable module command 3-44, 3-56, 3-63, 3-68 5-2, 5-3, 5-7 notes, usage in text 1-xv hw-module subslot shutdown command 5-5, 5-7 Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide IN-2 OL-5052-14...
  • Page 169 (figure) 3-32, 3-42 Management of TCP/IP-Based Internets 3-28, 3-39 interface specifications 3-33, 3-43 RFC 1157, Simple Network Management Protocol LEDs (SNMP) 3-28, 3-39 (figure) 3-32, 3-42 Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide IN-3 OL-5052-14...
  • Page 170 Cable management brackets for OC-48c/STM-16 POS/RPR SPA 3-36 chassis slot orientation (figure) Shipment deactivating Packing a SIP for deactivation (example) Packing a SPA for definition short reach double-height description Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide IN-4 OL-5052-14...
  • Page 171 1-xv Troubleshooting the installation Using debug commands 7-3, 7-7 Using show commands to Display Interface Information to Verify SIP and SPA Status Verifying the Installation Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide IN-5 OL-5052-14...
  • Page 172 Index Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide IN-6 OL-5052-14...

This manual is also suitable for:

7600 sip-600Cisco 7600 ssc-4007600 sip-2007600 sip-400

Table of Contents