HP D7171A - NetServer - LPr Installation Manual
Compaq 4000/7000 racks installation guide
Hide thumbs
Also See for D7171A - NetServer - LPr:
- Installation manual (182 pages) ,
- User manual (126 pages) ,
- Upgrade manual (97 pages)
Related Manuals for HP D7171A - NetServer - LPr
Summary of Contents for HP D7171A - NetServer - LPr
- Page 1 HP NetServer LH 3r, LH 4r, LH 3000r, and LH 6000r Installation Guide for Compaq 4000/7000 Racks ® HP Part Number 5969-5924 Printed in November 1999...
-
Page 2: Audience Assumptions
Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett-Packard. -
Page 3: Table Of Contents
Relocating the Control Panel ..............19 Installing the Bezel .................. 22 4 Warranty and Support ................23 Hardware Accessories Limited Warranty............23 Hewlett-Packard Hardware Accessories ..........23 Third-Party Hardware Products..............24 HP Repair and Telephone Support .............. 24 Index....................... 25... -
Page 5: Introduction
1 Introduction This document describes how to mount an HP NetServer LH 3r, LH 4r, LH3000r, ® or LH 6000r into a Compaq model 4000- or 7000-series rack enclosure. Refer to the documentation that came with the HP NetServer for instructions on adding accessories to, and configuring the NetServer. - Page 6 Chapter 1 Introduction WARNING To prevent the rack from tipping over and causing equipment damage or bodily injury, be sure that the stabilizing, anti-tip feature is installed on this rack enclosure see Figure 1-2. WARNING To prevent the rack from tipping over and causing equipment damage or bodily injury, do not extend more than one piece of equipment at a time out of the front of the rack enclosure.
- Page 7 Chapter 1 Introduction Figure 1-2. Single Rack Enclosure with the Anti-Tip Stabilizing Feature Installed...
-
Page 8: Hp Netserver - Compaq Rack Precautions
Chapter 1 Introduction HP NetServer – Compaq Rack Precautions CAUTION If this NetServer is not installed according to these instructions, damage to the NetServer or accessories may result. Damage due to improper installation is not covered by the HP Warranty. Observe the precautions listed in this section to maintain the NetServer’s reliability. -
Page 9: Overview
2 Overview The steps required to install the NetServer in the rack are summarized below: NOTE This is only a summary; detailed instructions are provided on the following pages. Measure and mark the appropriate holes on all four rack columns. Install one bar nut on each of the four rack columns. - Page 10 Chapter 2 Overview Terms used in this document are defined in the table below. Term Definition Bar nut Short, threaded bar used behind slide mounting flanges. Used in place of individual nuts to mate with slide mounting screws. Bezel Removable plastic fascia panel that covers entire front of the NetServer.
-
Page 11: Installation
3 Installation This section contains detailed instructions for installing an HP NetServer NetServer LH 3r, LH 4r, LH 3000r, or LH 6000r in the model 4000/7000 series of Compaq rack enclosures. Preparation Before beginning the installation of the NetServer into the rack, you must prepare the rack and the NetServer. - Page 12 Chapter 3 Installation 22nd 20th 22nd 20th (At Rear Of Column) 22nd 20th 15th 11th 22nd 20th 19th 14th Figure 3-1. Marking Holes for Installation Mark two holes on each of the front columns to use for rack nuts where the two recessed mounting brackets attach to the columns.
-
Page 13: Installing The Bar Nuts, Screws, And Cage Nuts
Chapter 3 Installation Installing the Bar Nuts, Screws, and Cage Nuts Once you have marked the appropriate holes, install the bar nuts and screws on the columns: 1. Position one bar nut behind holes 20 and 22 (previously marked). 2. Insert the two screws, with flat washers, through the two holes and start them into the bar nut see Figure 3-2. -
Page 14: Mounting The Slides
Chapter 3 Installation Mounting the Slides 1. Orient each slide so that the front of the slide attaches to the front column and the rear attaches to the rear column. This ensures that once installed, the slides will extend correctly, toward the front of the rack see Figure 3-3. - Page 15 Chapter 3 Installation 2. Place the mounting flange of the slide between the inside of the column and the bar nut. See Figure 3-4. Do this at the front and rear of the slide. Push In and Up Figure 3-4. Mounting a Slide to a Column 3.
-
Page 16: Installing The Netserver
Chapter 3 Installation Installing the NetServer The NetServer now must be mounted to the slides, the cable management arm can be installed, the recessed mounting brackets must be installed, the control panel must be relocated, and the Compaq rack-compatible bezel must be installed. Mounting the NetServer to the Slides 1. - Page 17 Chapter 3 Installation 3. Using two people, lift the NetServer using the handles on each side. Move the NetServer in between the extended slide members and position the it so that the handles are resting on the slide members see Figure 3-5 and Figure 3-6.
- Page 18 Chapter 3 Installation 4. Line up the mounting holes in the slide members with the holes in the NetServer chassis, insert three screws on each side, and tighten them see Figure 3-6. Figure 3-6. Attaching the Slides to the Server Chassis...
- Page 19 Chapter 3 Installation 5. Remove two screws from each of the four handles and remove handles see Figure 3-7. Keep these handles and screws for later use, in case you need to remove the NetServer and ship it. Figure 3-7. Remove Mounting Handles 6.
-
Page 20: Optional For Hp Netserver Lh 3000R And Lh 6000R, Install Cable Management Arm
Chapter 3 Installation Optional for HP NetServer LH 3000r and LH 6000r, Install Cable Management Arm The HP NetServer Cable Management Arm supplied with the HP LH 3000r and LH 6000r allows the cables, including the power cord, to move in and out with the HP NetServer chassis on its slides without being accidentally disconnected. - Page 21 Chapter 3 Installation 3. Install the two 6-32 pin head Torx T-15 screws in the two threaded holes on the rear of the NetServer. 4. Orient the cable management arm as shown in Figure 3-8. 5. Install the flange over the 6-32 screws and tighten them. 6.
-
Page 22: Installing The Recessed Mounting Brackets
Chapter 3 Installation Installing the Recessed Mounting Brackets The NetServer is held in the closed retracted position inside the rack enclosure by two recessed brackets. These are attached to the face of the NetServer chassis and the two front rack columns. To install these brackets: 1. -
Page 23: Relocating The Control Panel
Chapter 3 Installation 2. Install the four screws that hold the tall, left-hand bracket to the face of the NetServer chassis and to the rack column see Figure 3-10. 3. Install the four screws that hold the short, right-hand bracket to the face of the NetServer chassis and to the rack column see Figure 3-10. - Page 24 Chapter 3 Installation CAUTION Take care to not damage the ribbon cable that connects the control panel to the NetServer. 5. Reinstall the control panel in the leftmost slots, and install and tighten the screws. To avoid damaging the ribbon cable, verify that the ribbon cable goes completely back inside the NetServer before mounting the control panel.
- Page 25 Chapter 3 Installation 6. Mount the control panel bezel over the control panel see Figure 3-12. Install the bezel tabs into the leftmost slots. Mounting Slots for Compaq racks (on left) Mounting Slots for HP rack (on right) Figure 3-12. Reinstall the Control Panel Bezel...
-
Page 26: Installing The Bezel
Chapter 3 Installation Installing the Bezel Align the locating tabs on the Compaq rack-compatible bezel with the holes in the NetServer front panel, and clip the bezel onto the front of the NetServer see Figure 3-13. Figure 3-13. Installing the Compaq Rack-Compatible Bezel... -
Page 27: Warranty And Support
Hardware Accessories Limited Warranty Hewlett-Packard Hardware Accessories An HP NetServer Hardware Accessory is an internal HP hardware product that is specifically designated for use with HP NetServers; is added on or integrated into an HP NetServer in order to provide higher performance, capacity, or increased capability;... -
Page 28: Third-Party Hardware Products
Chapter 4 Warranty and Support Third-Party Hardware Products HP does not warrant third-party hardware products. Third-party hardware products may be warranted in accordance with the third-party warranty statement accompanying the product. On-site visits caused by third-party hardware products—whether internal to the HP NetServer system processor unit (such as non-HP DIMMs) or external to the system processor unit (such as LAN cabling)—are subject to standard per-incident travel and labor charges. -
Page 29: Index
Index Lockout releases, 18 Bezel, control panel, 21 Bezel, NetServer, 22 Mounting Brackets, 18 Mounting, NetServer, 12 Cable management arm, 16 Compaq, 1 NetServer, installing, 12 Control panel, 19 Control panel bezel, 21 Recessed brackets, attaching, 19 Fastening server to rack front, 18 Slide location, 7 Fastening server to slides, 14 Support, 24...