Hotpoint HDA3500NBB - Dishwasher w/ 5 Wash Cycles 6PUSHBTN Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Hotpoint Manuals
  4. Dishwasher
  5. HDA3500NBB - Dishwasher w/ 5 Wash Cycles...
  6. Installation instructions manual
Hotpoint HDA3500NBB - Dishwasher w/ 5 Wash Cycles 6PUSHBTN Installation Instructions Manual

Hotpoint HDA3500NBB - Dishwasher w/ 5 Wash Cycles 6PUSHBTN Installation Instructions Manual

Built-in dishwasher
Hide thumbs Also See for HDA3500NBB - Dishwasher w/ 5 Wash Cycles 6PUSHBTN:
Table of Contents

Advertisement

Quick Links

Appliances
Installation Instructions
Built-In Dishwasher
If you have questions, call 800.GE.CARES1800.432.2737} or visit our website at: www.ge.com
BEFORE YOU BEGIN
Read these instructions
completely
and
carefullg.
IM PORTANT-
Observe all governing
codes
and ordinances.
• Note to Installer
- Be sure to leave these
instructions
for the consumer and local inspector's
use.
• Note to Consumer - Keep these instructions with
your Owner's Manual for future reference.
• Skill Level-
Installation
of this dishwasher requires
basic mechanical,
electrical and plumbing skills.
Proper installation
is the responsibility
of
the installer.
Product failure due to improper
installation
is not covered under the GE
Appliance
Warranty.
See warranty
information.
• Completion
Time - I to 3 Hours. New installations
require more time than replacement
installations.
IM PORTANT-
The dishwasher
MUST be
installed
to allow for future removal from the
enclosure
if service is required.
If you received a damaged
dishwasher,
you should
immediately
contact
your dealer or builder.
Optional Accessories - See the Owner's Manual for
available custom panel kits.
FOR YOUR SAFETY
Read and observe all CAUTIONS and WARNINGS
shown throughout these instructions. While
performing installations describedinthisbooklet,
glovesand safetgglassesshould be worn.
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HDA3500NBB - Dishwasher w/ 5 Wash Cycles 6PUSHBTN and is the answer not in the manual?

Questions and answers

Related Manuals for Hotpoint HDA3500NBB - Dishwasher w/ 5 Wash Cycles 6PUSHBTN

Summary of Contents for Hotpoint HDA3500NBB - Dishwasher w/ 5 Wash Cycles 6PUSHBTN

  • Page 1 Appliances Installation Instructions Built-In Dishwasher If you have questions, call 800.GE.CARES1800.432.2737} or visit our website at: www.ge.com IM PORTANT- BEFORE YOU BEGIN The dishwasher MUST be installed to allow for future removal from the Read these instructions completely enclosure if service is required. carefullg.

  • Page 2: Tools You Will Need

    PARTS SUPPLIED IN INSTALLATION Screw Kit PACKAGE: Phi,,psHeadHexHead [] Two 8-18 x 5/8" Phillips heod wood screws _S Wood Screws Junction Box Screw [] Junction box cover and #10 hex head 5/8" long 1/2" long Junction Box Cover screw Drain hose (78" long) and hose clamp [] Cord protector (Power Cord Models Onlg) [] Conversion leads (Power Cord Models Onlg)

  • Page 3: Installation

    Installation Preparation-Enclosure • The dishwasher must be installed no more than PREPARE DISHWASHER ENCLOSURE 10 feet from sink for proper drainage. P!_V_Vl=_ ;t _11 _ [_ • The dishwasher must be fullg enclosed on the top, To reduce the risk of shock, fire, or injury sides, and back.

  • Page 4: Prepare Drain Plumbing

    Installation Preparation-Drain METHOD 1-Air Gap with Waste Tee or Disposer PREPARE DRAIN PLUMBING Drain Requirements • Followlocal codes and ordinances. • Drainhose must notexceed 10 feetinlength, • A highdrainloopor airgap isrequired. See below. Drain Method Figure C The type of drain installation depends on the Waste Tee Installation Disposer...

  • Page 5: Prepare Electrical Wiring

    Installation Preparation-Electrical Supply PREPARE ELECTRICAL WIRING P"v._V#l.,'1 :t _II_[_i Receptacle " I- Alternate -]" x FOR PERSONAL SAFETY: Remove house Locaton fuse or open circuit breaker before beginning installation. Do not use an iiiJ Receptacle -1-1/2" Dia.Hole (Max.) extension cord or adapter plug with this _1_"...
  • Page 6 Installation Preparation-Hot Water Supply PREPARE HOT WATER SUPPLY CAUTION Hot Water Line • The line may enter from either side, rear, or floor The hot water supply line pressure must be at least 20 PSI. within the shaded area shown in Figure F. Lower pressures could cause the water valve to leak and...

  • Page 7: Dishwasher Installation

    Dishwasher Installation STEP 3: REMOVE WOOD BASE CAUTION IM PORTANT - Donot kick off wood base! Do not remove the wood base until are ready Damage will occur. install the dishwasher. The dishwasher will tip over when the door is opened if the base is removed. •...
  • Page 8 Dishwasher Installation STEP 6: INSTALL 90 ° ELBOW STEP S: INSTALL POWER CORD • Wrap a 90° elbow with thread seal tape. Skip this step if the dishwasher will be • Thead the 90 ° elbow into the water valve. permanently connected to the house electrical...
  • Page 9 Dishwasher Installation is approximately 78" long. If a longer hose is needed, STEP 9: INSERT DRAIN HOSE AND POWER a 10 foot long hose may be purchased from an CORD, IF USED, THROUGH CABINET authorized GF appliance dealer. The 10 foot long •...

  • Page 10: Step 11: Slide Dishwasher

    Dishwasher Installation STEP 12: POSITION AND LEVEL STEP 11: SLIDE DISHWASHER INTO CABINET DISHWASHER IM PORTANT - Do not push against the front IMPORTANT- Dishwasher must be level for panel with knees. Damage will occur. proper dish reck operation, wash performance, and door operation.
  • Page 11 Dishwasher Installation STEP 13: FASTEN DISHWASHER STEP 14: CONNECT WATER SUPPLY UNDERSIDE OF COUNTERTOP OR SIDES Connect the water supply line to the 90° elbow OF CABINET installed in Step 6. • Slide the compression nut and then the ferrule over In this step Uou will need the two 5/8"...

  • Page 12: Drain Line

    Dishwasher Installation STEP 15: CONNECT DRAIN LINE Method 1 - Air gap with waste tee or disposer The molded end of the drain hose will fit 5/8" r¢ through 1" diameter inlet ports on the air gap, waste tee or disposer. •...
  • Page 13 Dishwasher Installation STEP 16: CONNECT POWER SUPPLY STEP 17: INSTALL JUNCTION BOX COVER If a power cord with plug is alreadg installed, If junction box cover is alreadg installed, skip to proceed to Step 17. Step 18. If the dishwasher came with a factory-installed In this step you will need the junction box cover and the #10 hex head screw from the screw kit set aside...
  • Page 14 Dishwasher Installation - Check the electrical connection to the water STEP 19: DISHWASHER WET TEST valve. The red electrical connector should be CHECK LIST plugged into the dishwasher water valve. If it is [] Turn on power supply or if power cord is used, not plugged in, turn off electrical power to the plug it into the wall outlet.
  • Page 15 Dishwasher Installation STEP 20: REPLACE ACCESS PANEL AND STEP 21: LITERATURE TOEKICK [] Leave the Owners' Hanual, Installation In this step gou will need the panels and the two Instructions, samples, and/or coupons with consumer. screws set aside in Step 4. There are two tgpes of screws used.
  • Page 16 Appendix Remove CONVERTING DISHWASHER WITH FACTORY StroinRelief EQUIPPED POWER CORD TO A PERMANENT CONNECTION This procedure requires the conversion leads set aside in Step 1. • Make sure the power cord for the dishwasher is unplugged from the wall outlet. •...

This manual is also suitable for:

Hda3500nbb 5 6pushbtn

Table of Contents