Hayward Super II Owner's Manual
Super ii pump series
Hide thumbs
Also See for Super II:
- User manual ,
- Installation and operating instruction manual (6 pages) ,
- Owner's manual (4 pages)
Advertisement
Table of Contents
- 1 Important Safety Instructions
- 2 Product Benefits
- 3 Installation Instructions
- 4 Pump Mounting
- 5 Start-Up and Operation
- 6 Prior to Start-Up
- 7 Priming Pump
- 8 Maintenance
- 9 Storing Pump for Winterization
- 10 Shaft Seal Change Instructions
- 11 Parts Diagram
- 12 Replacement Parts
- 13 Troubleshooting
- 14 Product Registration
- 15 Limited Warranty
- 16 Warranty Registration Card
- Download this manual
__________________________________________________________________________________________
The Hayward Super II Pump is specifically engineered for the demanding requirements of today's in-ground swimming pool/spa that
is equipped with large capacity filters, heaters, and pool cleaning equipment. The Super II is a self-priming pump that incorporates an
improved seal and impeller design that will provide many years of efficient, dependable, corrosion-free service. The advanced design
provides superior performance while reducing maintenance requirements.
To prevent potential injury and to avoid unnecessary service calls, read this manual carefully and completely.
WARNING –
CAUTION –
ATTENTION INSTALLER – THIS MANUAL CONTAINS IMPORTANT INFORMATION ABOUT THE
INSTALLATION, OPERATION, AND SAFE USE OF THIS PUMP THAT MUST BE FURNISHED TO THE END USER
OF THIS PRODUCT. FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS COULD RESULT IN SERIOUS
INJURY.
WWW.HAYWARDPOOL.COM
OWNER'S MANUAL
INSTALLATION, OPERATION, & PARTS
Super II
This product should be installed and serviced only by a qualified professional.
A licensed electrician MUST complete, in full, all electrical installations noted in this manual.
SAVE THIS INSTRUCTION MANUAL
Use of non-Hayward replacement parts voids warranty.
HAYWARD POOL PRODUCTS, INC.
620 DIVISION STREET ELIZABETH, NJ 07207 (908) 351-5400
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
™
Pump Series
WWW.HAYWARDPOOL.COM
P/N: IS3000XAZ-05
*50HZ Models are not UL or CSA Listed.
Rev. C
Advertisement
Table of Contents
Related Manuals for Hayward Super II
Summary of Contents for Hayward Super II
- Page 1 The Hayward Super II Pump is specifically engineered for the demanding requirements of today’s in-ground swimming pool/spa that is equipped with large capacity filters, heaters, and pool cleaning equipment. The Super II is a self-priming pump that incorporates an improved seal and impeller design that will provide many years of efficient, dependable, corrosion-free service. The advanced design provides superior performance while reducing maintenance requirements.
-
Page 2: Important Safety Instructions
Pool and spa components have a finite life. All components should be inspected frequently and replaced at least every ten years, or if found to be damaged, broken, cracked, missing, or not securely attached. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS... - Page 3 - In addition to two or more suction outlets per pump installed in accordance with latest IAF (formerly NSPI) standards and CPSC guidelines, follow all national, state, and local codes applicable. - Installation of a vacuum release or vent system, which relieves entrapping suction, is recommended. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
-
Page 4: Product Benefits
Failure to install according to defined instructions may result in severe personal injury or death. General Information Introduction This manual contains information for the proper installation and operation of the Hayward Super II Pump Series. The instructions in this manual MUST be followed precisely. Failure to install according to defined instructions will void warranty. -
Page 5: Installation Instructions
[40] [110] [63] [300] [90] [600] NOTE - It is recommended that a minimum length of piping, equivalent to 10 pipe diameters, be used between the pump suction inlet and any plumbing fittings. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS... - Page 6 14 AWG 0.75 0.55 14 AWG 208-230 14 AWG 1-1/2 1.10 0.75 12 AWG 208-230 14 AWG 1.55 1-1/2 1.10 10 AWG 2-1/2 1.87 1.55 208-230 12 AWG 2.20 2-1/2 1.87 208-230 12 AWG WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
-
Page 7: Start-Up And Operation
ATTENTION – NEVER run pump dry. Running pump dry may damage seals, causing leakage, flooding, and voids warranty. Fill strainer housing with water before starting motor. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS... -
Page 8: Priming Pump
Keep motor clean. Insure air vents are free from obstruction to avoid damage. Do NOT use water to hose off motor. Occasionally, shaft seals must be replaced, due to wear or damage. Replace with genuine Hayward seal assembly kit. See “Shaft Seal Change Instructions” in this manual. -
Page 9: Storing Pump For Winterization
To reduce risk of injury, do not permit children to use this product. B. Disconnect all electrical power service to pump before beginning shaft seal replacement. C. Only qualified personnel should attempt rotary seal replacement. Contact your local authorized Hayward Dealer or service center if you have any questions. - Page 10 15. Fasten assembly to pump/strainer housing using the six (6) 3/8”" x 2" housing cap screws. (Be sure housing gasket is in place, and replace if damaged). Tighten alternately and evenly. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
-
Page 11: Parts Diagram
™ Super II Pump Series ___________________ ____________________________ Page 11 of 14 Replacement Parts Parts Diagram Parts Listing WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS... -
Page 12: Troubleshooting
Solution: Contact qualified professional to check that the wiring gauge is heavy enough. NOTE Your Hayward pump motor is equipped with an “automatic thermal overload protector.” The motor will automatically shut off if power supply drops before heat damage can build up causing windings to burn out. The “thermal overload protector”... -
Page 13: Product Registration
Motor bearings noisy from normal wear, rust, overheating, or concentration of chemicals causing seal damage which will allow chlorinated water to seep into bearings wiping out the grease causing bearing to whine. Solution: All seal leaks should be replaced at once. © Hayward Pool Products, Inc. 2005 All rights reserved. PRODUCT REGISTRATION... -
Page 14: Limited Warranty
To obtain warranty replacements or repair, defective components or parts should be returned, transportation paid, to the place of purchase, or to the nearest authorized Hayward service center. For further Hayward dealer or service center information, contact Hayward customer service department. No returns may be made directly to the factory without the express written authorization of Hayward Pool Products, Inc.
Need help?
Do you have a question about the Super II and is the answer not in the manual?
Questions and answers