Refer To The Service Manual Of Ux-P100U; Chapter 3. Mechanism Blocks - Sharp A260 - UX B/W Thermal Transfer Service Manual

Service manual

Hide thumbs

Table of Contents

Enlarged version

SW-I7 No. 3, No. 4 AGC slew rate (Mic)

The AGC Slew Rate controls the convergence of the message playback

level to the desired playback level. A large slew rate will allow faster

convergence and a small slew rate will allow slower convergence.

SW-I7 No. 5 ~ No. 8 Reserved

Set to "0".

SW-J1 No. 1, No. 2 Reserved

Set to "0".

SW-J1 No. 3 Sender's phone number setting

Used to make a choice of whether the registered sender's phone number

can be changed or not. If the switch is set to "1", new registration of the

sender's phone number is disabled to prevent accidental wrong input.

SW-J1 No. 4, No. 5 Reserved

Set to "0".

SW-J1 No. 6 Summer time setting

This is used to set YES/NO of automatic clock adjustment for daylight

saving time.

SW-J1 No. 7, No. 8 Ringer volume

Used to adjust ringing volume.

SW-J2 No. 1 ~ No. 3 Reserved

Set to "0".

SW-J2 No. 4, No. 5 Handset receiver volume

Used to adjust the a handset receiver volume.

SW-J2 No. 6 ~ No. 8 Speaker volume (5 stages)

Used to adjust sound volume from a speaker.

SW-J3 No. 1 Reserved

Set to "0".

SW-J3 No. 2 ~ No. 4 Communication result printout (Transaction

report)

Every communication, the result can be output. As usual, it is set to print

the timer sending communication error alone. If No. 2: 0 No. 3: 1 No. 4:

0 are set, printing is always on (printed even if it is normally ended).

000: Error, timer and memory sending/receiving

001: Sending

010: Continuous printing

011: Not printed

100: Communication error

SW-J3 No. 5 ~ No. 8 OGM/ICM output level to speaker

(0dB ~ -15dB) (1dB step)

Used to control OGM and ICM output level to speaker.

SW-K1 No.1, No. 2 Reserved

Set to "0".

SW-K1 No. 3 ~ No. 8 OGM/ICM output level to Line

(0dB ~ -32dB) (1dB step)

Used to control OGM and ICM output level to Line.

SW-L1 No. 1 ~ No. 4 Reserved

Set to "0".

SW-L1 No. 5 Cut off mode (COPY mode)

Whether the excessive part is printed on the next recording paper or

discarded is selected to copy a document which is longer than the re-

cording paper.

SW-L1 No. 6 A4 Paper enable

The use of recording paper of A4 is enabled.

SW-L1 No. 7 LEGAL and LETTER paper enable

The use of recording paper of LEGAL and LETTER is enabled.

SW-L1 No. 8 Reserved

Set to "0".

SW-L2 No. 1, No. 2 Paper set size

At present size of the recording paper.

SW-L2 No. 3 Automatic reduce of receive

If set to 1, it is reduced automatically when receiving.

SW-L2 No. 4 ~ No. 6 Print contrast

Used for adjustment of print contrast.

SW-L2 No. 7 Reception reduction ratio in case of memory full

This model is designed so that the print is started according to the set-

ting of SW-L2 No.3 when reception of one page is completed. However,

if the memory is filled with data before completion of reception of one

page, the print is started with the reduction ratio which is set with this

switch.

SW-L2 No. 8 Reserved

Set to "0".

SW-M1 No. 1 ~ No. 8 Reserved

Set to "0".

SW-M2 No. 1 ~ No. 8 Reserved

Set to "0".

SW-N1 No. 1 ~ No. 8 Reserved

Set to "0".

SW-N2 No. 1 ~ No. 8 Reserved

Set to "0".

SW-N3 No. 1 ~ No. 8 Reserved

Set to "0".

SW-O1 No. 1 ~ No. 8 Reserved

Set to "0".

SW-O2 No. 1 ~ No. 8 Reserved

Set to "0".

SW-O3 No. 1 ~ No. 8 Reserved

Set to "0".

SW-O4 No. 1 ~ No. 8 Reserved

Set to "0".

SW-O5 No. 1 ~ No. 8 Reserved

Set to "0".

SW-O6 No. 1 ~ No. 8 Reserved

Set to "0".

[3] Troubleshooting