Contents Introduction -----------------------------------------------------------------------------------3 Battery Installation ------------------------------------------------------------------------4 Function Keys -----------------------------------------------------------------------------------5 Set up Your Remote Control Set-up by Brand and Code ------------------------------------------------------------------------------- Set-up by Auto Search ----------------------------------------------------------------------------------- Learn Function A. Learn a Command-------------------------------------------------------------------------------------------- B. Delete a Command------------------------------------------------------------------------------------------- C. Delete All Commands in a Device----------------------------------------------------------------------- D.
The F15DL also has “real time clock” to show your time and AM or PM. All above mentioned functions show you the URC20-F15D is a advanced, very powerful LCD universal remote control. Please read this user manual carefully prior to using you new LCD remote control.
Battery Installation This remote control needs 2 AAA batteries to work with. Fresh Alkaline batteries are strongly recommended. To install the batteries: 1. Turn the remote over, and lift the battery cover off. 2. Insert the batteries, matching the batteries to the (+) and (-) marks inside the battery compartment.
Page 5
Function Keys The number keys operate the For you start to set up the remote control same your original or show you the status in LCD remote control, and maybe also used for entering device codes when set up. Works like the TV/Video key on your original TV remote, select the input for TV.
Direct Set Up (by Brand and Code) This revolutionary method lets you directly choose the brand and code in LCD screen, simply set up your remote control even without manual book. 1.Turn on the device (e.g. your television set) you would like to operate. If it is a VCR, please insert a tape.
Page 7
2. Press the key on your new remote control for more than 3 seconds. Then release it. 3. Press the keys to select to “CODE SET UP” in LCD menu, and press the key. 4. The screen shows “DEV SEARCH” in the LCD menu, press the key to confirm.
3. When remote control searches through all codes, the remote control will stop at the beginning code of the search. 4. If the device is locked, you must first unlock the device then set up. Learn function is used to supplement the preprogrammed code list. The standard code list may provide most of functions needed, but you can add a small number of additional functions on your URC20-F15D.
Press a source key from original remote, e.g. Power S U C C E S S Receiver window Original Remote Control Target Key Source Key Remark: 1. A selected target key can be multi learnt from different sources keys, URC20-F15D will store the final learnt signal only. 2.
Page 10
L E A R N K E Y D E L E T E K E Y S E L E C T K E Y Select a key you want to delete delete next key SURE DELET S U C C E S S Delete All Command in a Device If you want to delete all learnt commands in a device with one operation in stead of deleting every key one by one, please follow the below steps:...
Page 11
Remark: sometimes it may take maximum about 3 minutes for delete all commands in one device. So if the commands are not many, suggest you delete commands one by one. D. Delete All Learnt Commands If you want to delete all learnt commands in your remote control, please follow the below steps: 1.
Press the key to move the cursor to select hour or minute or AM/PM, then press the number key to set hour and minute, and press the key to select AM or PM. Press the key to save the setting and LCD display “SUCCESS” exit to current setup state, if you enter errors the LCD screen shows ERROR”.
LOCK” to current setup state, You can press any device key (e.g. ) to finish set up or press the key to last state, or you can use to select other set S E T 3 S C O N F I G U R E 0 1 0 C O D E S E T U P 1 1 : 4 5...
Page 14
S E T 3 S C O N F I G U R E 0 1 0 C O D E S E T U P 1 1 : 4 5 T V O F F T I M E S E T U P D E V L O C K S U C C E S S...
key. Press the key to adjust contrast level, then press the key until you satisfied. Press the key to save the setting and the LCD shows SUCCESS then “CONTRAST” exit to current setup state. You can press any device key to finish set up or press the key to last state, or you can use select other set up.
Page 16
You can set up a Macro operation by following steps: 1. Press and hold the key for more than 3 seconds, and then release it. 2. Press the key to select “MACRO”, and then press the key. 3. Press the key to select the “MACR O1”...
I. Delete Macro 1. Press and hold the key for more than 3 seconds, then release it. 2. Press the key to select the “MACRO”, then press the key. 3. Press the key to select the “MACR O1”, then press the key.
Page 18
number, e.g.005 (you can find them in the BRAND CODE LIST at the attachment of this manual book) of the device brand by number button. 3. Please press the key to save it and exit, LCD shows “SUCCESS”. then return to current setup.
Page 19
Service and warranties: Your new 8-in-1 remote control is pre-programmed and can handle all important functions of your device. In case of technical inquiries or information concerning our product or its use, our service team is at your service, to help you through a free phone hotline or via email.
Need help?
Do you have a question about the URC-L-1870 and is the answer not in the manual?
Questions and answers