FUTABA R6208SB Manual

R6208SB
Thank you for purchasing a Futaba R6208SB S.BUS
compatible receiver.
The R6208SB has an S.BUS system output port and a
conventional system channel output. It can also be used with
conventional system servos, etc. in addition to S.BUS system
compatible servos and gyros, etc.
In addition, the operating mode (high-speed mode/normal
mode) can be selected.
* However, channel outputs 7 and 8 for conventional system oper-
ate in the normal mode even if set to the high-speed mode.
Applicable systems:
, TM10
10ch mode)
Compliance Information Statement
(for U.S.A.)
This device, trade name Futaba Corporation of America, model
number R6208SB, complies with part15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesiredoperation.
The responsible party of this device compliance is:
Futaba Service Center
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.
TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support)

What is S.BUS?

Different from conventional radio control systems the S.BUS
system uses data communication to transmit control signals
from a receiver to a servo, gyro, or other S.BUS compatible
device. This data includes commands such as "move the
channel 3 servo to 15 degrees, move the channel 5 servo to
[Connection by S.BUS system]
* Can also be used together with conventional servos.
* When using servos with a remote battery pack, use S.BUS Hub with Cable (2-way/remote battery pack use).
Please refer to the instruction manual of S.BUS Hub with Cable (2-way/remote battery pack use) for the connection method.
S.BUS compatible/FASST-2.4GHz (Multi-ch) system
8 channels/high-speed receiver
T8FG 2.4GHz
, TM14
(on 10ch mode)
Link/Mode switch
DATA port
R6208SB
R6208SB Ch output/
Battery terminal
S.BUS output
Battery
Conventional
servo
Usage condition on "High Speed mode"
 CAUTION
When using the high-speed mode, use a Futaba

digital servo (including brushless servo) or S.BUS
servo at conventional system use channels 1 to 6.
Analog servos cannot be used.
• The use of analog servos may cause servo trouble.
• When using analog servos, select the normal mode, and
use channel outputs 7 and 8.
, TM8
(on 8ch mode)
(on multi-ch mode)
LED

R6208SB Specifications

S.BUS compatible/FASST-2.4GHz (Multi-ch) system/8 channels/
high-speed receiver
• Dual antenna diversity
• Size: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3 mm)
• Weight: 0.49 oz. (13.8g)
• Power requirement: 3.7V to 7.4V
(Voltage range: 3.5 to 8.4V)
* Be sure that when using ESC's regulated output the capacity of the ESC
must meet your usage condition.
* The Battery F/S voltage is set for 4-cell NiCd/NiMH battery. Battery F/S
function doesn't work properly when other type battery is used.
30 degrees" to multiple devices. The S.BUS devices execute
only those commands for their own set channel. For this
reason, it can be used by connecting multiple servos to the
same signal line.
3ch
S.BUS hub S.BUS hub
S.BUS
2ch
S.BUS servo
, T10CG 2.4GHz
(on 8ch mode)
• Channel outputs for conventional
system (1 to 8)
• Battery terminal (B)
• S.BUS Port (S.BUS)
5ch
6ch
4ch
(on