Delta 50-850 Instruction Manual
  1. Manuals
  2. Brands
  3. Delta Manuals
  4. Dust Collector
  5. 50-850
  6. Instruction manual

Delta 50-850 Instruction Manual

Delta 1 1/2 h.p. single-stage dust collector instruction manual 50-850
Hide thumbs Also See for 50-850:

Advertisement

Table of Contents

1½ H.P. Single-Stage
Dust Collector
(Model 50-850)
PART NO. 902115 - 11-15-02
Copyright © 2002 Delta Machinery
To learn more about DELTA MACHINERY
ESPAÑOL: PÁGINA 15
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
1-800-223-7278 (
1-800-463-3582).
please call
In Canada call

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 50-850 and is the answer not in the manual?

Questions and answers

Related Manuals for Delta 50-850

Summary of Contents for Delta 50-850

  • Page 1 1½ H.P. Single-Stage Dust Collector (Model 50-850) PART NO. 902115 - 11-15-02 Copyright © 2002 Delta Machinery To learn more about DELTA MACHINERY ESPAÑOL: PÁGINA 15 visit our website at: www.deltamachinery.com. For Parts, Service, Warranty or other Assistance, 1-800-223-7278 ( 1-800-463-3582).

  • Page 2: General Safety Rules

    If you have any questions relative to a particular application, DO NOT use the machine until you have first contacted Delta to determine if it can or should be performed on the product.

  • Page 3: Additional Safety Rules For Dust Collectors

    13. REPLACE a damaged cord immediately. DO NOT use a damaged cord or plug. If the dust collector is not operating properly, or has been damaged, left outdoors or has been in contact with water, take it to an Authorized Service Center for service.

  • Page 4: Unpacking And Cleaning

    UNPACKING AND CLEANING Carefully unpack the tool and all loose items from the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose).
  • Page 5 WARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION MANUAL. ASSEMBLING CASTERS TO BASE 1. Insert threaded rod of caster (A) Fig. 4, into the hole located on the underside of base (B) and fasten with 3/8"...
  • Page 6 Fasten the remaining drum supports to the drum (J) in the same manner. 7. The dust collector is supplied with two 6" hose clamps (P) Fig. 13. Place one end of 6" dia. flexible hose (R) over blower/motor inlet (B) Fig. 14, and secure with hose clamp (P).
  • Page 7 9. Attach the lower dust bag retaining clip (A) Fig. 14A, to the dust collector drum. Align the two holes (B) in the retaining clip (A) Fig. 14A, with the two holes in the drum. Insert a 1/4-20x5/8" hex head screw through the holes in the retaining clip and the holes in the drum.
  • Page 8 5. Place the locking clamp (C) Fig. 22 around dust collection bag and dust collector drum and lock in place. NOTE: Make certain locking clamp is positioned in the channel of the dust collector drum before locking clamp.

  • Page 9: Grounding Instructions

    Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the dust collector. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

  • Page 10: Extension Cords

    If it is desired to operate your dust collector at 240 volts, single phase, contact your local Authorized Delta Service Center or qualified electrician for proper procedures to rewire your dust collector motor for 240 volt operation and wiring a 240 volt attachment plug to the power supply cord.

  • Page 11: Operating Controls

    (B). Your dust collector motor is supplied with a resettable circuit breaker. If the motor shuts off or fails to start due to an overload condition, turn the dust collector switch “OFF,” let the motor cool three to five minutes, and push the reset button (D) Fig.

  • Page 12: Parts, Service Or Warranty Assistance

    1-800-223-7278 (In Canada call 1-800-463-3582). Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two years and provides Delta with reasonable opportunity to verify the alleged defect by inspection.
  • Page 13 Delta products should be obtained by contacting any Porter-Cable · Service Center, or Porter-Cable Delta Factory Service Center. If you do not have access to any of these, call 800-223-7278 and you will · be directed to the nearest Porter-Cable Delta Factory Service Center.

Table of Contents

Save PDF