Related Manuals for NAIM ALLAE
Summary of Contents for NAIM ALLAE
- Page 1 W O R L D C L A S S H I F I O W N E R S M A N U A L I S S U E 2 Loudspeakers: SL2, allæ, Intro 2, axent, axess...
-
Page 2: Table Of Contents
1 Equipment Installation 3.1 switching on and off Normally your Naim equipment will have been installed by the dealer who sold it to you 3.2 running in even if you live outside their immediate vicinity. Your dealer is responsible for making 3.3 mains supply... -
Page 3: Mains Supply
In most territories a dealer must be prepared to take back improve system performance. any Naim equipment he has sold you if he cannot make it work to your satisfaction in your own home. A problem may Do not wire voltage dependent resistors or noise be due to a fault in any part of the system or its suppressors into mains plugs. -
Page 4: Connection
Use of non-standard speaker cables or interconnects may correct replacement must be obtained from your dealer, or invalidate your guarantee. from Naim Audio direct. Do not use the plug until the fuse carrier is replaced. 5.4 plug fuses Replace only with ASTA or BS 1362 approved fuses. - Page 5 6 Introduction and Positioning Naim loudspeakers are precision acoustic instruments that will only achieve optimal performance if installed and set up carefully. Please read these instructions before unpacking, installing and using the loudspeakers. Please also retain the packaging for future use.
- Page 6 Stage 2 Now move each Lower Cabinet with the Tweeter Suspension Take each Tweeter Suspension Assembly in turn and offer Assembly attached into the appropriate position. Take care it up to the Tweeter Mounting Points on the rear of each not to place them so close to the wall that the rear spikes Plinth.
- Page 7 Assembling and Installing SL2 (continued) 6.6 Connection It is vitally important for correct operation of SL2 that the If the loudspeakers are to be used with Naim amplification, Upper Cabinets are located properly on the Lower use only Naim loudspeaker cable. Cable lengths to both...
-
Page 8: Allæ, Intro 2
Intro 2 7 Introduction and Positioning Naim loudspeakers are precision acoustic instruments that will only achieve optimal performance if installed and set up carefully. Please read these instructions before installing and using the loudspeakers. Please also retain the packaging for future use. - Page 9 Intro 2 7.2 Connection If the loudspeakers are to be used with Naim amplification, If the allæ is to be used in an active system the passive use only Naim loudspeaker cable. Cable lengths to both crossover units should be removed and the Upper Cabinet loudspeakers should be equal and be between 3.5 metres...
-
Page 10: Axent, Axess
8 Introduction and Positioning Naim loudspeakers are precision acoustic instruments that will only achieve optimal performance if installed and set up carefully. Please read these instructions before installing and using the loudspeakers. Please also retain the packaging for future use. - Page 11 axent, axess 8.2 Tweeter Adjustment 8.4 Running in The tweeter is mounted on an adjustable suspension plate. Loudspeakers, like many hi-fi components, will take time to It is important both that the tweeter “bounces” freely on stabilise and “run-in” and can be expected to improve with the plate and that it is held in line with the front panel of use even over a period of weeks.
-
Page 12: Specifications
75 Watts (music programme) Dimensions (H x W x D): 873 x 240 x 276mm Declaration of conformity to appropriate standards Manufacturer Naim Audio Limited, Southampton Road, Salisbury, England, SP1 2LN Products SL2, allæ, Intro 2, axent, axess Safety HD 195-S6... - Page 13 Naim Audio Limited, Southampton Road, Salisbury, England SP1 2LN Part No. 0WMSP 12-001-0033 Drg No. NA401001-400 Telephone: +44 (0) 1722 332266 Fax: +44 (0) 1722 412034 www.naim-audio.com...
Need help?
Do you have a question about the ALLAE and is the answer not in the manual?
Questions and answers