Panasonic fv-05vs1 Supplementary Installation Instructions
Contractor pack
Hide thumbs
Also See for fv-05vs1:
- Installation instructions manual (17 pages) ,
- Installation instruction (16 pages) ,
- Installation instructions manual (16 pages)
Table of Contents
Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
Housing Can
FV-05-08VSA1
Applicable to Models: FV-05VS1, FV-08VS1
Please read these instructions carefully before attempting to install,
operate or service the Panasonic Ventilating Fan. Failure to comply
with instructions could result in personal injury and/or property
damage. Please retain this booklet for future reference.
Table of Contents
II
III
Installation
IV
Installation
V
VI
VII
VIII
IX
Product Service
SUPPLEMENTARY
(For Contractor Pack)
READ AND SAVE THESE INSTRUCTIOINS.
II
I
( -Joist Mounting )
( Between Joist Mounting )
II
III
)
Motor/Grille Assembly
FV-05VSB1, FV-08VSB1
2
2
3
3
4-6
6-7
8
8-9
9
10
10-11
11
12
12
Advertisement
Table of Contents
Related Manuals for Panasonic fv-05vs1
Summary of Contents for Panasonic fv-05vs1
-
Page 1: Table Of Contents
READ AND SAVE THESE INSTRUCTIOINS. Please read these instructions carefully before attempting to install, operate or service the Panasonic Ventilating Fan. Failure to comply with instructions could result in personal injury and/or property damage. Please retain this booklet for future reference. -
Page 2: General Safety Information
GENE AL SAFETY INFO MATION GENE AL SAFETY INFO MATION 1. Do not install this ventilating fan where air temperature may exceed 40 C (104 F). 2. Make sure that the electric service supply voltage is 120V, 60 Hz. 3. Follow all local electrical and safety codes, as well as the National Electrical Code (NEC) and the Occupation Safety and Health Act (OSHA). -
Page 3: Supplied Accessories
SUPPLIED ACCESSORIES SUPPLIED ACCESSORIES SETS SETS (A) For Motor / Grille Assembly of model: FV-05/08VSB1 Appearance Quantity Part name Grille (B) For Housing Can of model: FV-05-08VSA1 Appearance Quantity Part name Long screw (ST4.2X20) Thumb screw Screw (ST4.2X8) Screw (ST4.2X10) Suspension bracket I Suspension... -
Page 4: Installation I ( Joist Mounting- ) I
INSTALLATION INSTALLATION JOIST MOUNTING- JOIST MOUNTING- 1. Before installation, secure the fan body to adaptor by using thumb screw. (Fig.1) Thumb screw IMPORTANT : Remove the tape from damper and adaptor before installation. As shown below: Adaptor Damper Fan body Fig.1 Remove tape A=12 inches... -
Page 5: Installation Ii ( Joist Mounting- )
INSTALLATION INSTALLATION JOIST MOUNTING- JOIST MOUNTING- ) CONTINUED ) CONTINUED 3. Install the suspension bracket and the flange of fan body to joists by using long screws (ST4.2X20) according to Fig. 3. Joist Fan body Fig. 3-1 4 Long screws (ST4.2X20) A = 10 1/4~12 inches Joist 2 Long screws... - Page 6 INSTALLATION INSTALLATION JOIST MOUNTING- JOIST MOUNTING- ) CONTINUED ) CONTINUED 8. Finish ceiling work. Ceiling hole should be aligned with the edge of the flange. (Fig. 6) Ceiling 9. Follow the Fig. 12-3, 12-4 (page 9) and Fig. 7 (page 8) of the original installation instruction to complete the motor/grille assembly installation.
- Page 7 INSTALLATION INSTALLATION JOIST MOUNTING- JOIST MOUNTING- CONTINUED CONTINUED 5. Insert the fan body into joists. (Fig. 8) Circular duct IMPORTANT: Make sure that adaptor claws are properly inserted Joist Conduit into body slots. Junction box cover 6. Secure the fan body to adaptor by using thumb screw.
- Page 8 INSTALLATION INSTALLATION III I- III I- JOIST MOUNTING JOIST MOUNTING 4 kinds of -joist inches (mm) Suspension 9/16 ( 14.3 bracket III 11/16 (17.5) Screw 31/32 (24.6) (ST4.2X10) 1 17/32 38.9 Fig. 10 Suspension bracket The suspension bracket can comply with different kinds of -joist.
-
Page 9: Installationv ( Wooden Header )
INSTALLATION INSTALLATION IV ( IV ( BETWEEN JOIST MOUNTING BETWEEN JOIST MOUNTING ) CONTINUED ) CONTINUED 3. Insert the fan body between joists. Joists Make sure the fan body is level and square (perpendicular) with the joists. (Fig. 13) CAUTION: Ensure that distance B is no more than 1/2 inch (13 mm). -
Page 10: Installation Vi ( In Existing Construction )
INSTALLATION INSTALLATION VI ( VI ( IN EXISTING CONST UCTION IN EXISTING CONST UCTION 1. Installation in existing construction. Installing the ventilating fan in an existing building requires an accessible area (attic or crawl space) above the planned installation location or existing ducting and wiring. (1) To install the ventilating fan, follow the procedures described in lnstallation . - Page 11 INSTALLATION INSTALLATION WALL INSTALLATION- WALL INSTALLATION- ) CONTINUED ) CONTINUED 3. Secure it to studs by using long screws (ST4.2X20). 2 Long screws (Fig. 20) (ST4.2X20) 2 Long screws IMPORTANT: (ST4.2X20) Ensure distance C is 3/16 of an inch (5 mm) during the installation process as follows.
- Page 12 SERVICE CENTERS is maintained to support your product's warranty. (In the U.S.A.,call 1-866-292-7292 to Customer call center.) PANASONIC CONSUMER ELECTRONICS COMPANY Division de Panasonic Corporation of North America, One Panasonic Way, Secaucus, NJ 07094 PANASONIC CANADA INC. 5770 Ambler Driver, Mississauga, ON L4W 2T3 www.panasonic.com...