Sabre HS-RL-MSA Installation And Operating Instructions

MOTION SENSING ALARM
INSTALLATION AND OPERATING INSTRUCTIONS
These instructions should be kept in a safe place for future reference.
KIT CONTENTS:
1 x Motion Sensor 1 x Mounting Bracket
1 x Instruction Leaflet 3 x Screws and 3 x Wall Anchors
Siren
Indicator Light
Keypad
INTRODUCTION
The Keypad Controlled Motion Sensor can either be wall mounted using the bracket supplied or used freestanding
for portable use. It is operated using a 4-digit user access code with the keypad on the front of the alarm. The
system has 3 operating modes: CHIME, AWAY and HOME mode. CHIME mode is a low security feature that will
produce a door-chime sound when the alarm is triggered. In AWAY mode the device will produce a constant high
volume alarm sound after ENTRY delay when triggered. In HOME mode the unit will produce a constant high
volume alarm sound IMMEDIATELY after it is triggered.
INSTALLING BATTERIES & CREATING PERSONAL ALARM CODE
The keypad controlled door alarm requires 3xAAA alkaline batteries (not included).
1. Remove the battery compartment screw and slide off the cover in the direction of the open arrow.
2. Insert three AAA x batteries (not included). Take care to note the polarity diagram inside the battery
compartment.
3. LED light will start flashing – ENTER 4-digit personal code.
4. Code is confirmed when unit chirps twice and the LED light illuminates for 3 seconds.
5. Replace the battery compartment cover and secure the screw.
Model HS-RL-MSA
INSTALLATION
1. Select your desired location for the alarm, such as the corner of a room. This will provide the maximum
2. Secure the mounting bracket to the wall using the provided wall anchors or by screwing the mounting bracket
OPERATING IN PANIC MODE – PANIC MODE IMMEDIATELY
1. To activate PANIC mode press 1 and 4 at the same time. LED will keep blinking while alarming
2. To deactivate PANIC mode – Enter 4-digit pin
Mounting Bracket
OPERATING IN CHIME MODE
1. To activate CHIME mode, Press 1 and 2 at the same time.
2. Unit chirps twice – Enter 4-digit pin
3. Confirm – Unit will beep twice, LED light illuminates for 2 seconds and CHIME will sound.
4. To disarm CHIME mode – Enter 4-digit pin
5. Confirm disarm – unit will Beep twice
OPERATING IN ALARM MODE/SELECTING EXIT/ENTRY DELAYS
1. To activate ALARM mode, Press 2 and 3 at the same time
2. Unit will CHIRP and LED Light will flash.
3. Select EXIT/ENTRY Delays:
4. For delay selection confirmation unit will CHIRP and LED light will illuminate for 3 seconds
5. Once LED light turns off Enter 4-digit pin
6. Unit will Chirp twice and start EXIT delay countdown. LED light will flash for duration of delay.
7. Once the LED light stops flashing the unit is ARMED
8. When unit is triggered – LED light will flash for duration of ENTRY Delay – if unit is not disarmed using the
9. After unit is DISARMED the unit will beep twice for confirmation.
coverage.
NOTE: The sensor has a 6 m (20 ft) detection zone, with approximate angles of 110 degree horizontal and 70
degrees vertical. Recommended installation height is 1.8 – 2.4 m (6 – 8 ft).
directly into a wall stud. Once the mounting bracket is installed securely on the wall, insert the bracket of the
mount into the back of the unit and lock in place. The mount will click when secured to the alarm.
* PANIC can be activated in DISARM, CHIME AND ALARM modes
a. Press "1" for 10 second EXIT delay and 5 second ENTRY delay
b. Press "2" for 15 second EXIT delay and 10 second ENTRY delay
c. Press "3" for 30 second EXIT delay and 15 second ENTRY delay
d. Press "4" for 40 second EXIT delay and 30 second ENTRY delay
4-digit code the alarm will sound until DISARMED.