Related Manuals for PROTENT PRO-TENT MODUL 4000
Summary of Contents for PROTENT PRO-TENT MODUL 4000
- Page 1 PRO-TENT 5000 Pro-Tent MODUL 4000 1,5 x 1,5 / 2 x 2 / 3 x 1,5 / 3 x 2 / 4 x 2 /3 x 3 / 4,5 x 3 / 6 x 3 m Pro-Tent 5000 3 x 3 / 4,5 x 3 / 6 x 3 m...
- Page 2 P R O - T E N T M O D U L 4 0 0 0 / 5 0 0 0 AREAS OF APPLICATION Important points to note Product warranty • Pro-Tent tent systems have been designed for temporary We grant a 5-year warranty, starting from the day of sale for outdoor use to provide protection from sun and rain.
- Page 3 2 wheels for mounting on the bag d) 1 Torx key e) 1 adapter bar pliers f ) 1 assembly instructions g) 1 tensioning set (Pro-Tent MODUL 4000) or 1 professional set (Pro-Tent 5000) WHEEL ASSEMBLY Remove the wheels from the storage compartment.
- Page 4 A S S E M B L Y ASSEMBLY The Pro-Tent folding tent can be assembled comfortably by two people. Many steps should be carried out at the same time. This generally applies to the entire assembly and dis- mantling process. Step 1: Open the buckle at the bottom of the bag.
- Page 5 A S S E M B L Y Step 2: Hold the frame below the middle pivot point by the cross struts. This is the optimal handling position for opening the frame. Lift the frame slightly and open it by stepping back only so far that the gable pole extends about 10 cm.
- Page 6 A S S E M B L Y Step 4: Fasten the velcro straps on the inside of the roof corners tightly underneath the plastic connector around the pole. Make sure that the reinforcement flap is placed symmetrically and without creases around the pole beforehand. Step 5: Fixing the roof gable to the protection cover: Push the recess/ slot on the fabric sleeve through the tongue on the profile...
- Page 7 A S S E M B L Y Step 6: Grasp the frame again below the middle pivot point at the cross struts, lift slightly and open the frame by stepping backwards until the roof begins to stretch. Step 7: To engage the roof struts, the plastic gliders must be pushed out over the top push buttons of the corner poles.
- Page 8 A S S E M B L Y Step 8: Easy tightening of the fabric roof by using the velcro straps. To do this, pull the roof panel down a little first. Step 9: Now pull out all the poles to the end position (2). Functional explanation of how to engage the poles Push button spring in the upper pole (locking of the gliders)
- Page 9 D I S M A N T L I N G DISMANTLING 1. Loosen all velcro straps on the roof panel. 2. Press the red push button release below the plastic gliders on each pole. This unlocks the roof frame. 3.
- Page 10 A C C E S S O R I E S / S I D E W A L L S SIDE WALLS Side wall 1. Secure the side panel horizontally with Velcro between the two posts on the inside roof surround. 2.
- Page 11 A C C E S S O R I E S / S I D E W A L L S 4. Then press the four rails into the slot in the lower posts. Close the zip fasteners again afterwards Removing the side wall 1.
- Page 12 A C C E S S O R I E S / C R O S S - C O N N E C T O R S Cross-connectors 1. Pull the top edge with the piping of the half-height side wall into the cross-connector, align the connec- tor at the height of the side wall between the two poles and lock it in...
- Page 13 A C C E S S O R I E S / O P T I O N A L P O L E S Optional poles Pro-Tent MODUL 4000 Attach the optional pole below the gable (5-8): Push the Optional poles can be inserted at each connection node.
- Page 14 In contrast to the optional pole to the end position (6). Pro-Tent MODUL 4000 support pole, which only requires one adjustable adapter, the Pro-Tent 5000 has two separate optional support poles for the 3-piece connector and 4-piece connector.
- Page 15 If the ground conditions do not allow you to use pegs, you can also use ProTent weight plates or ProTent water weights (see the next page). As a general rule, we recommend weighing down even tensioned tents with weight plates.
- Page 16 SECURING IN WINDY CONDITIONS Hexagonal weight plate 12.5 kg The weight plate is completely inside the folding tent and can be stacked up to 6 layers (up to 75kg per pole). The feet of the poles are fixed to the bottom weight plate with ball locking pins. Water weight 50 litres The water weights are a useful alternative if pegging is not possible or if you want to secure your folding tent with additional weight (50 kg per pole).
- Page 17 pro-tent.com...
Need help?
Do you have a question about the PRO-TENT MODUL 4000 and is the answer not in the manual?
Questions and answers