Synchronous Recording; Recording Playback Signals From A Vcr With Rs-422A - JVC BD-X200U - Dvd Authoring Recorder Instructions Manual

Synchronous Recording

Recording Playback Signals From a VCR with RS-422A

RS-422A control can be used to record playback signals from a VCR with an RS-422A terminal to a disc in your BD-X200.It will also
be possible to control that VCR using this DVD recorder's REMOTE CONTROL screen.
Signal Connections
VIDEO IN
LAN
SIGNAL
GND
USB terminal
Keyboard
Esc F1 F2 F3 F4 F5 F6 F7 F8 F9
-
1 2 3 4 5 6 7 8 9 0
Q W E R T Y U I O P
Tab
@
Caps Lock A S D F G H J K L
;
Z X C V B N M < > ?
Shift
, /
Ctrl Alt Alt
Connect the RS-422A REMOTE terminal on the rear of the DVD recorder to the remote RS-422A terminal on the VCR using an
RS-422A cable.
Connect the DVD recorder's VIDEO LINE IN and AUDIO IN terminals to the VCR's video out and audio out terminals.
Connect the DVD recorder's VIDEO LINE OUT and AUDIO OUT terminals to the monitor's video in and audio in terminals.
A keyboard and mouse can be used as an alternative to the DVD recorder's buttons when using the REMOTE CONTROL screen.
If used, these are to be connected to each of the USB terminals on the rear panel.
Setup Procedures
Insert the tape for playback into the VCR. Ensure that this tape contains an SMPTE time code.
Insert a recordable disc into your BD-X200.
Settings
VCR : Enable control via RS-422A.
BD-X200 : Set REMOTE SELECT from the REMOTE MENU screen to 9PIN (MASTER).
REMOTE MENU screen
REMOTE MENU
MENU
REMOTE SELECT
REC CONTROL
REM FF/REW MODE
Note
When pressing and holding the REC
button more than 2 seconds while the DVD
recorder is stopped, encoded output
images can be checked while the button
is being held.
VIDEO OUT
AUDIO IN
VIDEO AUDIO
IN LINE OUT INPUT CH1
LEVEL
IN OUT
4dB
8dB
Y/C
IN
CH2
REMOTE
DV IN/OUT
REMOTE
USB
DC 19V
Print Pause
Scroll
F10 F11 F12 Screen
Lock
Sysrq Break
Back Page Num
Insert Home *
Space Up Lock
^
7 8 9
Enter Page
Delete End
Down
+
4 5 6
:
Mouse
1 2
Shift
Enter
.
0
Ctrl
When REMOTE SELECT is set to 9PIN (MASTER), the REMOTE CONTROL
(9PIN MASTER) screen will appear. This screen is used to perform editing
operations, and the corresponding operations are described on the following
pages.
9PIN(MASTER)
OFF
FF/REW
AUDIO OUT
Monitor
REMOTE CONTROL (9PIN MASTER) screen
REMOTE CONTROL SCREEN ( 9PIN MASTER )
IN POINT
EXIT
: : :
h m s f
1 00:00:00:00
4
00:25:00:00
7 00:40:00:00
CHAPTER
ADJ
BITRATE
TC SET
TC CANCEL
AUDIO OUT VIDEO OUT
AUDIO VIDEO
AUDIO INPUT / AUDIO MONITOR SELECT
INPUT INPUT
SDI CH1 CH2 CH3 CH4 SIF
AES/EBU
AUDIO CH1 CH2 CH3 CH4 LINE
MONITOR L
ANALOG
CH1 CH2 CH3 CH4 CPN
R
Variable Motion
CH1 CH2 CH3 CH4/ TRACKING
R P R P R P R P
TC UB DF SERVO CF GEN 16:9 AP 525
dB OVER dB dB OVER dB dB OVER dB dB OVER dB CTL CONDITION
AUTO OFF P.READ V.V A R PB/EE R E M O TE 625
0 0 0 0
+4 +4 +4 +4
+2 –10 +2 –10 +2 –10 +2 –10
0 0 0 0
–20 –20 –20 –20
–2 –30 –2 –30 –2 –30 –2 –30
H M S
–40 –40 –40 –40
–4 –4 –4 –4
–60 –60 –60 –60
ASSEM VIDEO DA1 DA2 DA3 DA4
CH1 CH2 CH3 CH4
TRACKING
PHONES REC
INSERT
IN ENTRY OUT TC
PULL FOR VARIABLE METER MODE
CANCEL PREVIEW AUTO EDIT PREROLL
FINE TRACKING
PULL
RELEASE
PLAY SHIFT REVIEW
USER
VCR with an RS-422A terminal
00:00:00:00
OUT POINT 00:10:00:00
: : : : :
h m s f h m s
2 00:15:00:00 3 00:20:00:00
5 6
00:30:00:00 00:35:00:00
8 00:45:00:00 9 00:50:00:00
:
TC INPUT
MANUAL
000 min
8.0 Mbps
DISC REMAIN
FINALIZE
EDL LOAD
EDIT/END
VIDEO CASSETTE RECORDER
POWER
ON I
OFF O
SEARCH VAR PLAYER RECORDER
COUNTER RESET VCON REMOTE
UB
PB
P.PLAY
MENU SET HOLD PB/EE
STILL
F
EJECT REC PLAY PAUSE/STILL
X-1 X1
TOP VIDEO AUDIO
STAND BY REW STOP FF
PULL
RELEASE
SERVO/SYS TIME CODE ON SCREEN OTHERS
REV FWD
MONITOR OUT
Monitor
:
f
:
59