Advertisement
Quick Links
Owner's Manual &
Safety Instructions
tM
24f
Model
He092
2" X 48" BeLt GrinDer
WarninG:
to prevent serious injury, user must read and
understand Owner's Manual. SaVe tHiS ManuaL.
When unpacking, make sure that the product is intact and undamaged.
If any parts are missing or broken, please call 1-888-866-5797
as soon as possible. Reference 58875.
Advertisement
Related Manuals for Hercules HE092
Summary of Contents for Hercules HE092
- Page 1 Owner’s Manual & Safety Instructions Model He092 2" X 48" BeLt GrinDer WarninG: to prevent serious injury, user must read and understand Owner’s Manual. SaVe tHiS ManuaL. When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-888-866-5797...
- Page 2 table of contents Safety ................2 Maintenance .............10 Specifications ............6 Parts List and Diagram ..........12 Setup .................6 Warranty ..............16 Operation ..............8 WarninG SyMBOLS anD DeFinitiOnS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
- Page 3 13. DON’T OVERREACH. table a: recOMMenDeD MiniMuM Wire GauGe Keep proper footing and balance at all times. FOr eXtenSiOn cOrDS (120 VOLt) 14. MAINTAIN TOOLS WITH CARE. Keep eXtenSiOn cOrD tools sharp and clean for best and safest naMepLate performance. Follow instructions for LenGtH aMpereS lubricating and changing accessories.
- Page 4 Grounding instructions tO preVent eLectric SHOcK anD DeatH FrOM incOrrect GrOunDinG Wire cOnnectiOn reaD anD FOLLOW tHeSe inStructiOnS: 110-120 Vac Grounded tools: tools with three prong plugs 1. In the event of a malfunction or breakdown, 6. Repair or replace damaged or grounding provides a path of least resistance for worn cord immediately.
- Page 5 9. DO nOt Operate WitH any GuarD 14. Industrial applications must follow OSHA guidelines. DiSaBLeD, DaMaGeD, Or reMOVeD. Moving 15. Maintain labels and nameplates on the tool. guards must move freely and close instantly. These carry important safety information. 10. The use of accessories or attachments not If unreadable or missing, contact recommended by the manufacturer may Harbor Freight Tools for a replacement.
- Page 6 Specifications Electrical Rating (prewired for 120V) 120/240V/60Hz/7/3.5A Belt Speed 4500 SFPM Motor Size 1 HP Sanding Belt Size 2″ W x 48″ L Setup - Before use: read the entire iMpOrtant SaFety inFOrMatiOn section at the beginning of this manual including all text under subheadings therein before set up or use of this product. tO preVent SeriOuS inJury FrOM acciDentaL OperatiOn: turn the power Switch of the tool off and unplug the tool from its electrical outlet before performing any procedure in this section.
- Page 7 Mounting 1. Select a workbench or mounting location that is able to support the weight of the Sander, plus any additional weight placed on it during use. Use the mounting bolt holes in the Base to mount. Mounting hardware not included. assembly Screw (38) 1.
- Page 8 Operating instructions read the entire iMpOrtant SaFety inFOrMatiOn section at the beginning of this manual including all text under subheadings therein before set up or use of this product. tool Set up tO preVent SeriOuS inJury FrOM acciDentaL OperatiOn: turn the power Switch of the tool off and unplug the tool from its electrical outlet before performing any procedure in this section.
- Page 9 adjusting Belt assembly position (Vertical to Horizontal) Screw (19) 1. Loosen Screw (19). 2. Rotate Belt Assembly to desired position. 3. Tighten Screw. Belt Frame Workpiece and Work area Set up 1. Designate a work area that is clean and well lit. 3.
- Page 10 Maintenance and Servicing procedures not specifically explained in this manual must be performed only by a qualified technician. tO preVent SeriOuS inJury FrOM acciDentaL OperatiOn: turn the power Switch of the tool off and unplug the tool from its electrical outlet before performing any procedure in this section.
- Page 11 troubleshooting problem possible causes Likely Solutions Sander does 1. Not plugged in. 1. Plug in Sander. not turn on 2. No power at outlet. 2. Check power at outlet and/or circuit breaker. 3. Safety Key not inserted into Switch. 3. Insert Safety Key into Switch. 4.
- Page 12 parts List and Diagram parts List part Description part Description Screw Spring Pin Washer Rubber Foot Screw Support Rod Base Plate Belt support Capacitor Support Spring Screw Washer Capacitor ON/OFF Switch Screw Screw Spring Switch Plate Idler Wheel Support Base Belt Tension Lever Bolt Bolt...
- Page 13 assembly Diagram 58875 For technical questions, please call 1-888-866-5797. Page 13...
- Page 14 Wiring Diagram record product’s Serial number Here: note: if product has no serial number, record month and year of purchase instead. note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Specify UPC 193175448088 when ordering parts. Page 14 For technical questions, please call 1-888-866-5797.
- Page 15 pLeaSe reaD tHe FOLLOWinG careFuLLy THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
- Page 16 Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
Need help?
Do you have a question about the HE092 and is the answer not in the manual?
Questions and answers