Do you have a question about the FREEWAY and is the answer not in the manual?
Questions and answers
Niel
April 10, 2025
Jabra 100 HFS
Niel
April 10, 2025
Please provide easiest way to pair Jabra Freeway HFS 100. I lost instructions. Unit still good but need to pair to iPhone. Thanks.
1 comments:
Mr. Anderson
April 10, 2025
To pair the Jabra FREEWAY HFS 100 with an iPhone:
1. Turn on the Jabra FREEWAY. 2. The first time you turn it on, it enters pairing mode automatically. The Answer/End button flashes blue, and voice guidance begins. 3. If voice guidance is off, go to your iPhone’s Bluetooth settings and search for new devices. 4. Select "Jabra FREEWAY" from the list. 5. If prompted for a passkey, enter 0000. 6. When pairing is complete, you will hear “Connected.” The device is now ready to use.
F Voice button Tap to initiate voice command functions G Visor clip H Power switch Slide to ON position to turn the FREEWAY on I Micro USB charging connector Charge with the Micro USB charger J Charging indicator light Light red while charging and turns off when fully charged...
WHAT YOUR SPEAKERPHONE CAN DO Your Jabra FREEWAY lets you do all this: - Make and answer calls just using your voice - Ease of use with Jabra Voice Guidance - Last number redialing and call back last number - Voice dialing* - Three way calling* - Advanced MultiUse™ - be connected to two active Bluetooth...
CHARGE YOUR SPEAKERPHONE Make sure that your speakerphone is fully charged before you start using it . Use the USB cable to connect Jabra FREEWAY to the car charger . Plug the car charger into your car’s power outlet . The charging indicator light will light up in red while charging .
- Slide the On/Off power switch to turn the speakerphone on or off . - If the switch is left in the On position the Jabra FREEWAY will automatically turn on and reconnect to your phone when you enter your car (open the car door) .
1 Activate Bluetooth® on your phone/device 2 Turn the Jabra FREEWAY on 3 The first time you turn the FREEWAY on it will automatically enter into pairing mode . The Answer/end button will flash with a blue light and you will be voice guided through the pairing process .
NOTE: If you have disabled Voice Guidance you can put Jabra FREEWAY in pairing mode manually by pressing and holding the Answer/end button while you slide the power switch into the On position . The Answer/end button will flash blue to indicate that you are in pairing mode .
HOW TO The Jabra FREEWAY is easy to operate . The buttons performs different functions depending on how long you press them . Instruction Duration of press Press briefly Double tap Press briefly two times within 1/2 second Press Approx: 1-3 second...
Page 10
- You can also place a call directly from your phone . If your phone is connected it will automatically transfer the call to your Jabra FREEWAY* . If the call does not transfer, tap the Answer/ end button .
When you have an incoming call you can answer or ignore just using you voice . You do not have to touch Jabra FREEWAY or you phone . Just say “Answer” to take the call and “Ignore” to reject .
Page 12
”Cancel” Will cancel the current operation and close the voice menu When you are playing music on the Jabra FREEWAY you can at any time tap the Voice button to remote control you music player using your voice . Voice control – While listening to music*...
Page 13
The Jabra FREEWAY is loaded with voice announcements that talks you through setup and daily operation . In the table below you can see the most common announcements . Voice guidance FREEWAY What it means announcements to you “Welcome! You are now The FREEWAY is in pairing mode .
.* You can also start your music player by tapping the Voice button . Wait for the FREEWAY to ask you to ”Say a command” and then say ”Play”* . When playing music you can at any time tap the Voice button again and: - Say ”Next track”...
If you experience interference from a radio station on your set frequency you can either tap the FM button to quickly redirect the audio back to the FREEWAY or press the VOL+ button to search for a new frequency .
. The LED’s will be enabled every time you reconnect or power on the FREEWAY . Download Firmware updates and additional languages Go to jabra .com/freeway and download the latest firmware and additional languages . TROUBLESHOOTING & FAQ I hear crackling noises - Bluetooth is a radio technology, which means it is sensitive to objects between the speakerphone and the connected device .
Page 17
. Please consult your device manual for details . Please note that some features can only be operated from the primary device e .g . voice dial using Jabra FREEWAY with 2 mobile phones . I can not connect speakerphone and radio via FM transmitter - Make sure the radio is turned on and speakerphone is in FM mode (FM Status Icon is on) .
ID to function properly . NEED MORE HELP? 1. Web: www .jabra .com (for the latest support info and online User Manuals) 2. E-mail: Deutsch support .de@jabra .com English support .uk@jabra .com...
– or below -10°C/14°F) . This can shorten battery life and may affect operation . High temperatures may also degrade performance . - Do not expose the Jabra FREEWAY to rain or other liquids . JABRA FREEWAY...
. 4 Passkey or PIN is a code that you enter on your Bluetooth enabled device (e .g . a mobile phone) to pair it with your Jabra FREEWAY . This makes your device and the Jabra FREEWAY recognize each other and automatically work together .
Need help?
Do you have a question about the FREEWAY and is the answer not in the manual?
Questions and answers
Jabra 100 HFS
Please provide easiest way to pair Jabra Freeway HFS 100. I lost instructions. Unit still good but need to pair to iPhone. Thanks.
To pair the Jabra FREEWAY HFS 100 with an iPhone:
1. Turn on the Jabra FREEWAY.
2. The first time you turn it on, it enters pairing mode automatically. The Answer/End button flashes blue, and voice guidance begins.
3. If voice guidance is off, go to your iPhone’s Bluetooth settings and search for new devices.
4. Select "Jabra FREEWAY" from the list.
5. If prompted for a passkey, enter 0000.
6. When pairing is complete, you will hear “Connected.” The device is now ready to use.
This answer is automatically generated