Advertisement
Quick Links
Advertisement
Related Manuals for ICT CAN/ULC-60839-11-1
Summary of Contents for ICT CAN/ULC-60839-11-1
- Page 1 Wireless Lock Range Motorized Deadbolt Wireless Lock Installation Manual...
- Page 2 The specifications and descriptions of products and services contained in this document were correct at the time of printing. Integrated Control Technology Limited reserves the right to change specifications or withdraw products without notice. No part of this document may be reproduced, photocopied, or transmitted in any form or by any means (electronic or mechanical), for any purpose, without the express written permission of Integrated Control Technology Limited.
- Page 3 Contents Introduction About This Product How Does It Work? Hardware Options MIFARE Technology About MIFARE Secured MIFARE Card Format About MIFARE DESFire EV1 About MIFARE DESFire EV2 About MIFARE DESFire EV3 MIFARE/DESFire Products Installation Requirements Installation What's Included? Installing the Latch Installing the Strike Plate Installing the Outside Trim Installing the Inside Mounting Plate...
- Page 4 CAN/ULC-60839-11-1 UL 294 UL 10B UL 10C FCC Compliance Statements Industry Canada Statement Disclaimer and Warranty Motorized Deadbolt Wireless Lock | Installation Manual...
- Page 5 Introduction This installation manual provides instructions and technical specifications for installation of the ICT Motorized Deadbolt Wireless Lock. About This Product The ICT Motorized Deadbolt Wireless Lock combines an advanced-technology, intelligent wireless credential reader with leading motorized deadbolt locking system technology. With no cabling necessary this provides sites with the ability to deploy integrated electronic access control in areas where traditional wired locking solutions may not be possible.
- Page 6 ⦁ Premises, Safes and Vaults CAN/ULC-S561, Installation and Services for Fire Signal Receiving Centres and Systems ⦁ CAN/ULC-60839-11-1, Alarm and Electronic Security Systems – Part 11-1: Electronic Access Control Systems – ⦁ System and Components Requirements ⦁ The National Electrical Code, ANSI/NFPA 70 ⦁...
- Page 7 Connect the cable (see page 15). Install the inside trim (see page 16). What's Included? The ICT Motorized Deadbolt Wireless Lock is supplied with the following components. 1 x 13.56MHz lock control card reader with Bluetooth® Wireless Technology ⦁ The reader is built into the outside assembly.
- Page 8 Installing the Latch Prepare the door according to the door template. Install the latch with the cross slot for the tailpiece towards the bottom. Using the 2 x #18 x 3/4" combo screws provided, secure the latch in position. Installing the Strike Plate Close the door and, using the faceplate as a guide, mark the position for the strike plate.
- Page 9 Installing the Outside Trim Set the door handing. Left Hand Door: Rotate the tailpiece clockwise until it stops in the vertical orientation. Right Hand Door: Rotate the tailpiece counter-clockwise until it stops in the vertical orientation. From the outside of the door, feed the reader cable through the hole to the other side. Important: You must feed the reader cable under the latch.
- Page 10 Installing the Inside Mounting Plate Feed the reader cable through the cable slot at the bottom of both the mounting plate and rubber gasket. Position the mounting plate in place over the hole in the door, followed by the rubber gasket. Ensure the rubber gasket is on the outside of the mounting plate, as shown below.
- Page 11 Connecting the Cable Secure the reader cable through the hook in the mounting plate as shown below. Ensuring the cable is not twisted or knotted, plug the reader cable into the main socket at the bottom of the lock control board firmly so that it clicks into place. Motorized Deadbolt Wireless Lock | Installation Manual...
- Page 12 Installing the Inside Trim Taking care not to pinch the cable, install the inside trim onto the door. Confirm that the thumbturn correctly operates the deadbolt latch. Using the two M4 x 12 pan head screws provided, secure the inside trim in position. Insert the 4 x AA batteries provided.
- Page 13 Bluetooth® Node Connection Online operation is achieved using a Bluetooth® communication node, wired to the controller's RS-485 port to act as a network connection point between the wireless lock and the controller. One Bluetooth® node supports up to 20 wireless locks operating in online mode. Using the recommended cables, splice the cable together with the pigtail of the Bluetooth®...
- Page 14 Shield Connection Connect the Bluetooth® node pigtail shield and cable shield wires together at the node pigtail splice. Connect the cable shield to a suitable earth point. Do not connect the cable shield to a ground or AUX connection. The node pigtail shield wire is not terminated inside the reader.
- Page 15 Programming the Reader ICT credential readers can be programmed for a wide range of functionality to suit your site's requirements. Programming options are dependent on hardware compatibility and firmware versions. Readers can be programmed using a mobile device running the Protege Config App.
- Page 16 Operation ICT wireless locks provide specific audio and visual signals to indicate read response and current status. The following table describes the available LED and beeper response signals. Beeper Indicators Short beeps have a sound and interval duration of 100ms. ⦁...
- Page 17 Operation LED Indication LED Description Beeper 2 Purple flashes (100ms/100ms) Construction Mode - Access Granted - Battery Low < 3.55V 2 short 1 Red flash (200ms) 3 Orange flashes Construction Mode - Access Denied 1 long (100ms/100ms) 2 Orange flashes (100ms/100ms) Construction Mode - Access Denied - Battery Low <...
- Page 18 Maintenance ICT motorized deadbolt wireless locks have an expected battery life of approximately 1 year (10,000 activations), dependent on usage levels and reader configuration. Maximum 17,000 activation cycles with MIFARE/DESFire or NFC credentials ⦁ Maximum 18,000 activation cycles with Bluetooth® Wireless Technology credentials ⦁...
- Page 19 Mechanical Layout 34mm 27.7mm 75.2mm (2.96”) (1.34”) (1.09”) 75.4mm (2.97”) Motorized Deadbolt Wireless Lock | Installation Manual...
- Page 20 Door Template May not be to scale. MARK CENTER OF DOOR THICKNESS FOR 25.4mm (1") DIA. HOLE 4mm (5/32") 25.4mm (1") MORTISE BOLT 60.3mm (2 3/8") BACKSET BOLT AND DOOR THICKNESS 69.9mm (2 3/4") BACKSET NOTE: ADJUST TEMPLATE FOR BEVELED DOORS Motorized Deadbolt Wireless Lock | Installation Manual...
- Page 21 New Zealand and Australia Intentional Transmitter Product Statement The R-NZ compliance label indicates that the supplier of the device asserts that it complies with all applicable standards. Motorized Deadbolt Wireless Lock | Installation Manual...
- Page 22 European Standards CE Statement Conforms where applicable to European Union (EU) Low Voltage Directive (LVD) 2014/35/EU, Electromagnetic Compatibility (EMC) Directive 2014/30/EU, Radio Equipment Directive (RED)2014/53/EU and RoHS Recast (RoHS2) Directive: 2011/65/EU + Amendment Directive (EU) 2015/863. This equipment complies with the rules, of the Official Journal of the European Union, for governing the Self Declaration of the CE Marking for the European Union as specified in the above directive(s).
- Page 23 UK Conformity Assessment Mark General Product Statement The UKCA Compliance Label indicates that the supplier of the device asserts that it complies with all applicable standards. Motorized Deadbolt Wireless Lock | Installation Manual...
- Page 24 If fire resistance is required for door assembly, portal locking device(s) must be evaluated to ULC-S533 and CAN/ULC-S104. ⦁ Must be installed with CAN/ULC-60839-11-1 Listed portal locking device(s) for ULC installations. ⦁ Input power must be supplied by a Class 2 or power limited device.
- Page 25 FCC Compliance Statements FCC PART 15, WARNINGS: INFORMATION TO USER This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 26 Industry Canada Statement This class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. CAN ICES-3 (A)/NMB-3(A) Motorized Deadbolt Wireless Lock | Installation Manual...
- Page 27 Integrated Control Technology Ltd nor its employees shall be liable under any circumstances to any party in respect of decisions or actions they may make as a result of using this information. In accordance with the ICT policy of enhanced development, design and specifications are subject to change without notice.
- Page 28 In accordance with the ICT policy of enhanced development, design and specifications are subject to change without notice.
Need help?
Do you have a question about the CAN/ULC-60839-11-1 and is the answer not in the manual?
Questions and answers