iOttie Easy One Touch Wireless 2 (HLCRIO142) Manual

Getting Started

For optimal mounting and charging, please follow the detailed instructions within this manual when using the Easy One Touch Wireless 2 Charging Mount. iOttie is not liable for possible damages due to product misuse.

Critical Information

• Compatibility
  Google, Apple & Samsung Wireless Fast Charge Compatible. The Easy One Touch Wireless 2 delivers wireless fast charging to all Qi enabled smart phones (Qi speed dependent on phone make and model)
• Qi Wireless Charging in Vehicle
  Use the included iOttie Car Charger and Micro USB Cable. If you do use a third party car charger, use a Qualcomm Quick Charge 2.0 or equivalent adapter to receive a wireless charge (with compatible devices).
• The Easy One Touch Wireless 2 Charging mount's signal could possibly interfere with your TPMS (tire pressure monitoring system). If you notice that your TPMS light turns on, please try to use your mount in different locations to avoid the signals from interacting.

Telescopic Arm extends from 5 inches to 7 inches.

To reuse Suction Cup, s imply rinse under warm water and let air dry to restore tacky suction.

At a Glance

Qi Alignment Guide

The Qi Receiver Coil is usually located in the center area of the phone. Check with your phone's manufacturer for Qi coil location. Below are some examples for commonly used phones.

For optimal wireless charging, please make sure your smartphone and mount's Qi coils are aligned.

Alignment & Connecting to Power

Foot Release Button

The Foot can be adjusted to 3 different height settings to accommodate different phone sizes, once setup is chosen, the foot is designed to align with the center of the side arms for optimal Qi Wireless charging.

Cradle Knob

When mounting in and scape mode, loosen to rotate the Cradle. Tighten to lock in desired position.

The Easy One Touch Wireless 2 is powered via a micro-USB cable. There is no on/cff switch on the device. Once it is plugged in. the device will remain on unless the vehicle shuts off power when in parking mode.

Installation

Assembling the Mount

1. Connect the Mount Cradle with the Ball Joint.
   

2. Then, tighten the Cradle Knob.
   

Selecting a Location

Choose an installation method: Dashboard/Flat Surface (A) or Windshield/Curved Glass (B).

Option A: Dashboard or Flat Surface Installation

Choose an area on a flat surface on the vehicle's dashboard and wipe any dust Or debris from the surface.

1. Peel off the film on the dashboard pad & stick on the desired installation location.
   
2. Peel off the protective film on the Suction Cup and press mount firmly onto the dashboard pad.
   
3. Push Locking Lever down to engage suction.
   

Option B: Windshield Installation or Curved Glass Installation

Choose a location on the windshield and wipe any dust or debris from the surface.

1. Peel Off the protective film on the Suction Cup and press firmly onto the windshield.
   
2. Push Locking Lever down to engage suction.
   

Adjusting the Mount

Telescopic Knob

Located on top of Telescopic Arm, loosen to extend the arm, and tighten to secure distance.

Pivot Knob

Located on the side of the Mount Base, turning allows you to pivot telescopic arm. Tighten to secure position.

Using the Easy One Touch Mechanism

The Easy One Touch lock and release mechanism makes it simple to mount & retrieve smartphones in seconds.

Mounting

1. Press the locking side arms In.
   
2. Press your device against the Easy One Touch trigger button. The mount's arms will automatically close on contact and hold the device during the driving journey.
   

Releasing

Press the locking side arms with one hand and retrieve the device.

Wireless Charger Specifications

Car Charger Specifications

Charging Indicator

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download iOttie Easy One Touch Wireless 2 (HLCRIO142) Manual