Be careful in the selection and duration of television formats used for viewing. Uneven PDP aging as a result of format selection and use, as well as burned-in images, are not covered by your Samsung limited warranty. User Instructions...
Table of Contents General Information Channel Control Your New Plasma Display Panel ......6 Fine Tuning Channels ........64 Remote Control Buttons ........8 Connecting a PC and Operation Wall Installation Instructions ......10 How to assemble the Stand-Base ....14 Connection a PC ........66 Connecting Speakers ........15 Adjusting the PC Screen ......70 Changing the Position of the Image....71...
General Information Your New Plasma Display Panel ............6 Remote Control Buttons ..............8 Wall Installation Instructions ............10 How to assemble the Stand-Base ............14 Connecting Speakers ..............15...
Your New Plasma Display Panel Front Panel Power Indicator SOURCE/ENTER button - Power Off : Red Press to display all of the available video sources. - Power On : Off (ie., TV, AV, S-Video, Component, PC, DVI). - Timer On : Green Press to confirm a selection.
Page 7
Rear Panel Œ DVI INPUT Ø AV (VIDEO / L-AUDIO-R) Video and audio inputs for external Connect to the digital video and audio devices, such as a camcorder or VCR. output jack of a device with DVI output. ∏ COMPONENT ´...
Page 9
Œ POWER button S. MODE button Turns the PDP on and off. Select Sound effect. ´ Number buttons Ò PRE-CH button Tunes to the previous channel. ˇ +100 button Ú TV/VIDEO button Press to select channels over 100. For Press to display all of the available video example, to select channel 121, press sources (ie., Video, S-Video, Component,...
Wall Installation Instructions This wall mount bracket installation guide is for the following models: PL-42D4S Installation Notes Do not install the PDP on any location other than a vertical wall. To protect the performance of the PDP and prevent problems, avoid the following locations: •...
How to assemble the Wall Mount Bracket The wall mount comes packaged in 3 parts. These parts must be assembled together. Please tighten the captive screw in the direction of the arrow after assembling the bracket. Install the Wall Mount Bracket after the screws are securely inserted into the wall.
Page 12
Wall Installation Instructions Fixing the PDP panel to the wall attachment panel bracket Remove the screws from the back of the PDP. Connect insulation holders to screws (see the illustration below). • If you are uncertain about installation, hire a specialist to install the wall mount bracket. •...
How to Adjust Mounting Angle Notice : Please secure the mounting bracket on the wall surface after setting its angle at 0°. Notice Factory default How to Adjust Mounting Angle Please tighten the captive screw in the direction Hold onto the middle of the PDP to adjust of the arrow after assembling the bracket.
How to assemble the Stand-Base Assemble two support pins with the stand base and firmly secure both sides of the support pins using 8 screws provided. Assemble the PDP with the stand and firmly secure the PDP using 4 screws provided. ➤...
Connecting Speakers Remove the screws on the rear of the PDP. Hang the two “T” shaped hangers on the square holes on the rear of the PDP. Tighten the PDP and the speaker bracket using the screws removed from the PDP. ➤...
Page 16
Connect the speaker audio cable to the external speaker output jack on the rear of the PDP matching the “+” and “-” ends of the cable with the diagram on the PDP. ➤ ➤ The speakers MUST have to a power handling capability of 10 watts minimum (impedance 8Ω). When you connect the speaker wire to the external speaker out connector, first bind the speaker wire round the ferrite core to secure it.
Connections Connecting VHF and UHF Antennas ..........18 Connecting Cable TV..............19 Connecting a VCR................21 Connecting a Camcorder ..............22 Connecting a DVD Player..............23 Connecting a DTV Receiver ............24...
Connecting VHF and UHF Antennas Antennas with 75-ohm Round Leads If your antenna looks like this: it has 75-ohm round leads. Plug the antenna lead into the VHF/UHF terminal on the PDP. Use the Antenna Cable, an accessory included in the product package.
Connecting Cable TV You can connect different cable systems to your PDP, including cable without a cable box, and cable with a cable box that descrambles some or all channels. Cable without a Cable Box Plug the incoming cable into the VHF/UHF terminal on the PDP.
Page 20
Cable with a Cable Box that Descrambles Some (But Not All) Channels To complete this connection you will need a two-way splitter, an RF (A/B) switch, and four coaxial cables (which you can buy from your Samsung dealer or any electronics store). Find and disconnect the cable that is con- nected to the ANTENNA IN terminal of your cable box.
Connecting a VCR Connecting a VCR to the Video or S-Video/Audio jack Power Plug Audio Cable S-Video Cable Video Cable How to Connect Connect the Video/Audio cables between the VIDEO or S-VIDEO / L - AUDIO - R jacks on the PDP and VIDEO or S-VIDEO / L - AUDIO - R output jacks on the VCR.
Connecting a Camcorder Viewing camcorder tapes Camcorder Power Plug Video Cable Audio Cable How to Connect Connect a Video/Audio cable between the VIDEO or S-VIDEO / L - AUDIO - R jacks on the PDP and the VIDEO or S-VIDEO /AUDIO output jacks on the camcorder. (Note: For better video, you can use an S-VIDEO cable) Note •...
Connecting a DVD Player (480i, 480p) This PDP displays the optimum picture in 720p mode. Playing DVD DVD Player Power Plug Video Cable Audio Cable How to Connect Connect a Video Cable between the Y, P (COMPONENT) input jacks on the PDP and Y, P output jacks on the DVD player.
Connecting a DTV Receiver (480p, 720p, 1080i) This PDP displays the optimum picture in 720p mode. Watching DTV DTV Receiver Power Plug Video Cable Audio Cable DVI Cable Use a DVI-D connection cable. (sold separately) How to Connect Connect the cable or antenna to the antenna input jack on the DTV. Connect a Video cable between the Y, P (COMPONENT) or DVI jack on the PDP and the Y, P...
Operation Turning the PDP On and Off ............26 Plug & Play Feature ..............28 Memorizing the Channels..............31 Viewing an External Signal Source ..........36...
Turning the PDP On and Off Turning the PDP On and Off Press the POWER button on the remote control. The PDP will be turned on and you will be ready to use its features. You can also use the POWER ( )button on the front of the PDP.
Page 27
Displaying Status Information Press the INFO button on the remote control. The PDP will display the Picture mode, Sound mode, MTS, Mono Caption, and Clock. V-Chip Picture : Custom Sound : Custom : Stereo Clock : 12 : 00 am...
Plug & Play Feature When the television is initially powered ON, several basic customer settings proceed automatically and subsequently. The following settings are available. If the television is in Standby mode, press the Plug & Play POWER button on the remote control. Start Plug &...
Page 29
Select the correct signal source (Air, STD, HRC and Air/CATV IRC) by pressing the ▲ or ▼ button, then press the ENTER button. Move Enter Skip To start the search, press the ENTER button. Auto Program ➤ ➤ The search will end automatically. Channels are sorted and stored in an order which reflects their position in the frequency range (with lowest first and highest last).
Page 30
Plug & Play Feature (continued) If you want to reset this feature... Press the MENU button. Press the ▲ or ▼ button to Setup select “Setup”, then press the ENTER button. Language : English √ Time √ Caption √ Digital NR : On √...
Memorizing the Channels Your PDP can memorize and store all of the available channels for both “off-air” (antenna) and cable channels. After the available channels are memorized, use the and CH buttons to scan through the channels. This eliminates the need to change channels by entering the channel digits.
Page 32
Storing Channels in Memory (Automatic Method) First, select the correct signal source (Air, STD, HRC Channel and IRC). See steps on previous page. Air/CATV : Air √ Press the MENU button. Press the ▲ or ▼ button to Auto Program √...
Page 33
Adding and Erasing Channels (Manual Method) First, press the CH or CH button or the number buttons to select the channel you want to add or delete. Press the MENU button. Press the ▲ or ▼ button to Channel select “Channel”, then press the ENTER button. Air/CATV : Air √...
To View Memorized Channel Press the MENU button. Press the ▲ or ▼ button to Channel select “Channel”, then press the ENTER button. Air/CATV : Air √ Auto Program √ Add/Delete √ Fine Tune √ Scan √ Move Enter Return Press the ▲...
Changing Channels Using the Channel Buttons Press the CH or CH button to change channels. When you press the CH or CH button, the PDP changes channels in sequence. You will see all the channels that the PDP has memorized. (The PDP must have memorized at least three channels.) You will not see channels that were either erased or not memorized.
Viewing an External Signal Source Use the remote control to switch between viewing signals from connected equipment, such as VCRs, DVD, Set-Top box and the TV source (broadcast or cable). Setting the Signal Source Input Press the MENU button. Press the ENTER button to select “Input”.
Assigning Names to External input mode Input Press the MENU button. Press the ENTER button to select “Input”. Source List : TV √ Edit Name √ Edit Name Move Enter Return Press the ▲ or ▼ button to select “Edit Name”, then Edit Name press the ENTER button.
Picture Control Customizing the Picture ..............40 Using Automatic Picture Settings ............41 Selecting the Color Tone..............42 DNIe (Digital Natural Image engine) ..........43 Changing the Screen Size ............44 Freezing the Picture ..............46 Viewing the Picture-in-Picture............47 Selecting a Signal Source (Antenna or Cable) for PIP ......52...
Customizing the Picture You can use the on-screen menus to change the Contrast, Brightness, Sharpness, Color, and Tint settings of your PDP. Press the MENU button. Press the ▲ or ▼ button to Picture select “Picture”, then press the ENTER button. Mode : Custom √...
Using Automatic Picture Settings Your PDP has automatic picture settings that allow you to adjust the video display easily. Press the MENU button. Press the ▲ or ▼ button to Picture select “Picture”, then press the ENTER button. Mode : Custom √...
Selecting the Color Tone Picture Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Mode : Custom √ Custom √ Color Tone : Normal √ Color Control √ Film Mode : Off √...
DNIe (Digital Natural Image engine) Samsung’s New Technology brings you more detailed images with contrast, white enhancement and 3D noise reduction. Picture Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button.
Changing the Screen Size Screen size selection depends on the type of video input ( DVD, PC etc.). Picture Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Mode : Custom √...
Page 45
16:9(W ide) 16:9(W ide) 16:9 Aspect Ratio that fits DVD and Wide Screen applications. 16:9 Panorama Panorama Fits a 16:9 picture onto a 4:3 screen and displays it without clipping the image. Panorama Zoom Zoom Magnifies the 16:9 wide picture (in a vertical direction) to fit the screen size.
Viewing the Picture-in-Picture Selecting the PIP Screen Picture Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Mode : Custom √ Custom √ Color Tone : Custom √ Color Control √ Film Mode : Off √...
Selecting an External Signal You can use PIP to view a signal from an external source, such as a VCR. Picture Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Mode : Custom √...
Swapping the Contents of the PIP Image and Main Image Picture Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Mode : Custom √ Custom √ Color Tone : Normal √ Color Control √...
Changing the Size of the PIP Window Picture Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Mode : Custom √ Custom √ ➤ ➤ Color Tone : Normal √ Quick way to access PIP size: Just press the “P.SIZE” button on the Color Control √...
Page 51
Changing the Location of the PIP Image Press the MENU button. Press the ▲ or ▼ button to Picture select “Picture”, then press the ENTER button. Mode : Custom √ Custom √ Color Tone : Normal √ Color Control √ Film Mode : Off √...
Selecting a Signal Source (Antenna or Cable) for PIP If the PIP source is TV while PIP is ON, you can select the broadcasting source of PIP picture separately from the main picture. Press the MENU button. Press the ▲ or ▼ button to Picture select “Picture”, then press the ENTER button.
Changing the PIP Channel Picture Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Mode : Custom √ Custom √ Color Tone : Normal √ Color Control √ Film Mode : Off √...
Sound Control Customizing the Sound ..............56 Using Automatic Sound Settings ............57 Choosing a Multi-Channel Sound (MTS)Soundtrack ......58 Using the Auto Volume ..............59 Setting the TruSurround XT ............60 Selecting the Internal Mute ............61...
Customizing the Sound Press the MENU button. Press the ▲ or ▼ button to Sound select “Sound”, then press the ENTER button. Mode : Custom √ Custom √ : Stereo √ Auto Volume : Off √ SRS TSXT : Stereo √...
Using Automatic Sound Settings Press the MENU button. Press the ▲ or ▼ button to Sound select “Sound”, then press the ENTER button. Mode : Custom √ Custom √ : Stereo √ Auto Volume : Off √ SRS TSXT : Stereo √...
Choosing a Multi-Channel Sound (MTS) Soundtrack Depending on the particular program being broadcast, you can listen to stereo, mono, or a Separate Audio Program. (SAP audio is usually a foreign-language translation. Sometimes SAP has unrelated information like news or weather.) Press the MENU button.
Using the Auto Volume Each broadcasting station has its own signal conditions, which can make it necessary to adjust the volume every time the channel is changed. “Auto volume” lets you automatically adjust the volume of the desired channel by lowering the sound output when the modula- tion signal is high or by raising the sound output when the modulation signal is low.
Setting the TruSurround XT TruSurround XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers. Trusurround delivers a compelling, virtual surround sound experience through any two-speaker playback system. It is fully compatible with all multichannel formats. Press the MENU button.
Selecting the Internal Mute The internal speakers can be muted in order to hear sound from external speakers you've connected. Press the MENU button. Press the ▲ or ▼ button to Sound select “Sound”, then press the ENTER button. Mode : Custom √...
Fine Tuning Channels Use fine tuning to manually adjust a particular channel for optimal reception. Channel Press the MENU button. Press the ▲ or ▼ button to select “Channel”, then press the ENTER button. Air/CATV : Air √ Auto Program √...
Connecting a PC and Operation Connecting a PC................66 Adjusting the PC Screen..............70 Changing the Position of the Image..........71 Picture Quality Adjustment ............72 Information ..................75...
Connecting a PC Connection to a Macintosh computer may require an adapter. Power Plug DVI Cable Use a DVI-D Audio Cable connection cable. Audio Cable (sold separately) PC Cable DVI jack (The actual configuration on your PC may be different, depending on the model.) Connecting a PC (15p D-SUB) to the PDP Connect a PC cable between the PC Output jack on the PC and the RGB input jack on the PDP.
Pin Configuration D-Sub Cable DVI-D Cable (Digital-Only Connector) • 15Pin Signal Cable (based on protruded pin) Setting up Your PDP (Plug and Play) Our adoption of the new VESA Plug and Play solution eliminates complicated and time consuming setup. It allows you to install your monitor in a Plug and Play compatible system, without the usual setup hassles and confusion.
Page 68
Windows and your particular video card. But even if your actual screens look different, the same, basic set-up information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.) 1. Right click the mouse on the Windows Desktop, then click on [Properties].
Page 69
Notes Both screen position and size will vary, depending on the type of PC monitor and its resolution. The table below shows all of the display modes that are supported: Video Signal Resolution Vertical Horizontal Vertical Horizontal (Dot X Line) Frequency(Hz) Frequency(KHz) Polarity...
Adjusting the PC Screen Adjusting the R.G.B Preset: • Press the TV/VIDEO button to select “PC”. Press the MENU button. Press the ▲ or ▼ button to Picture select “Picture”, then press the ENTER button. Mode : Custom √ Custom √...
Changing the Position of the Image After connecting the PDP to your PC, adjust the position of the screen if it is not well-aligned. Preset: • Press the TV/VIDEO button to select “PC.” Press the MENU button. Press the ▲ or ▼ button to Setup select “Setup”, then press the ENTER button.
Picture Quality Adjustment Picture Automatic Adjustment Preset: • Press the TV/VIDEO button to select “PC”. Press the MENU button. Press the ▲ or ▼ button to Setup select “Setup”, then press the ENTER button. Language : English √ Time √ Caption √...
Page 73
Coarse Adjustment Preset: • Press the TV/VIDEO button to select “PC”. Press the MENU button. Press the ▲ or ▼ button to Setup select “Setup”, then press the ENTER button. Language : English √ Time √ Caption √ Digital NR : On √...
Page 74
Fine Tuning (Fine) Preset: • Press the TV/VIDEO button to select “PC”. Press the MENU button. Press the ▲ or ▼ button to Setup select “Setup”, then press the ENTER button. Language : English √ Time √ Caption √ Digital NR : On √...
Information Preset: • Press the TV/VIDEO button to select “PC”. Press the MENU button. Press the ▲ or ▼ button to Setup select “Setup”, then press the ENTER button. Language : English √ Time √ Caption √ Digital NR : On √...
Setting the Clock Press the MENU button. Press the ▲ or ▼ button to Setup select “Setup”, then press the ENTER button. Language : English √ Time √ Caption √ Digital NR : On √ V-Chip √ Miscellaneous √ √ Move Enter Return...
Setting the Sleep Timer You can set your PDP to automatically turn off after a preset interval. Setup Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Language : English √ Time √...
Setting the Timers This PDP can be set to turn on or off automatically at specific times that you choose. Before using the timers, you must set the PDP’s clock, as described previously. Press the MENU button. Press the ▲ or ▼ button to Setup select “Setup”, then press the ENTER button.
Page 81
On Timer Press the √ button to select “Channel”, then press the ▲ or ▼ button to select the channel you want Hour Minute am/pm when PDP turns on. Channel Volume Activation Air 3 Adjust Move Return On Timer Press the √ button to select “Volume”, then press the ▲...
Function Description Selecting a Menu Language .............84 Digital Noise Reduction ............85 Selecting the Film Mode ............86 Setting the Melody Sound ............87 Setting the Blue Screen.............88 Viewing Closed Captions ............89 Using the V-Chip ..............90...
Selecting a Menu Language Press the MENU button. Press the ▲ or ▼ button to Setup select “Setup”, then press the ENTER button. Language : English √ Time √ Caption √ Digital NR : On √ V-Chip √ Miscellaneous √ √...
Digital Noise Reduction If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction feature to help reduce any static and ghosting that may appear on the screen. Setup Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button.
Selecting the Film Mode On: Automatically senses and processes film signals from all sources and adjusts the picture for optimum quality. Off: Switches off the Film mode. Picture Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. Mode : Custom √...
Setting the Melody Sound You can hear clear melody sound when the television is powered on or off. Setup Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Language : English √...
Setting the Blue Screen If no signal is being received or the signal is very weak, a blue screen automatically replaces the noisy picture background. If you wish to continue viewing the poor picture, you must set the “Blue Screen“ mode to “Off“. Setup Press the MENU button.
Viewing Closed Captions Your TV decodes and displays the closed captions that are broadcast with certain TV shows. These captions are usually subtitles for the hearing impaired or foreign language translations. All VCRs record the closed caption signal from television programs, so home-recorded video tapes also provide closed captions.
Using the V-Chip The V-Chip feature automatically locks out programs that are deemed inappropriate for children. The user must enter a PIN (personal ID number) before any of the V-Chip restrictions are set up or changed. Note: When the V-chip feature is activated, the PIP and auto channel program features do not function.
Page 91
How to Enable/Disable the V-Chip Setup Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Language : English √ Time √ Caption √ Digital NR : On √ V-Chip √ Miscellaneous √...
Page 92
How to Set up Restrictions using the “TV Parental Guidelines” First, set up a personal identification number (PIN), and enable the V-Chip. (See previous section.) Parental restrictions can be set up using either of two methods: The TV guidelines or the MPAA rating. Setup Press the MENU button.
Page 93
TV Parental Guidelines At this point, one of the TV-Ratings is selected. Press the ENTER button. Depending on your existing setup, a symbol will be selected. (Blank = Unblocked, = Blocked) While “ ” is selected, press the ENTER button to block or unblock the category.
Page 94
How to Set up Restrictions using the MPAA Ratings: G, PG, PG-13, R, NC-17, X, NR The MPAA rating system uses the Motion Picture Association of America (MPAA) system, and its main application is for movies. When the V-Chip lock is on, the TV will automatically block any programs that are coded with objection- able ratings (either MPAA or TV-Ratings).
Page 95
How to Reset the TV after the V-Chip Blocks a Channel (“Emergency Escape”) If the TV is tuned to a restricted channel, the V-Chip will block it. The screen will go blank and the following message will appear: Press the ENTER button. Received Rating : TV-PG This channel is blocked by V-Chip.
Troubleshooting If the TV seems to have a problem, first try this list of possible problems and solutions. If none of these troubleshooting tips apply, then call your nearest service center. Problem Possible Solution Poor picture. Check all wire connections. Your Remote control does not Press the “TV/VIDEO”...
Care and Maintenance With proper care, your PDP will give you many years of service. Please follow these guidelines to get the maximum performance from your PDP. Identifying Problems • Do not put the PDP near extremely hot, cold, humid or dusty places. •...
Specifications Exterior design and product specifications are subject to change without prior notice to improve the performance of this product. Model PL-42D4S 1028 (W) X 86.4 (D) X 685 (H) mm (with stand) Dimensions Display Weight Display 33.24 kg (with stand)