Phanteks Enthoo 719 - PC Case Manual

The Enthoo 719 has been designed to house the most powerful hardware and the flexibility to configure it to your needs for the perfect system. From SSI-EEB motherboards to extreme water cooling and extensive storage capabilities, anything is possible. When combined with the Revolt X or Revolt PROeven a Dual System or the most powerful workstations can be a reality. The Enthoo 719 is capable of the extreme in style with quality materials such as aluminum, tempered glass and integrated Digital-RGB lighting. Phanteks believes that meaningful designs are created through the fusion of form and function.

SPECIFICATIONS

EXPLOADED VIEW

ACCESSORIES

3.5" MODULAR HDD BRACKET

• 4 included in accessory box
• For 3.5" or 2.5" Drive

CONFIGURE YOUR ENTHOO 719
The Enthoo 719 has the most versatile chassis design, providing you with a myriad of options. With so many possibilities to pick from, you can use this overview to choose and plan the best configuration for your build.

GETTING STARTED

PREPARATIONS

• The Enthoo 719 case is designed to support installation in a standing position.
• Don't turn on the power to your system until installation is complete.
• Discharge your body's static electric charge by touching a grounded surface before performing any hardware procedure.
• Make sure to consult the manuals of your hardware before installation.

If you do not feel comfortable with performing the installation procedure, consult a qualified computer technician.

2. REMOVING FRONT PANEL
   

3. REMOVING RIGHT SIDE PANEL
   

4. REMOVING LEFT SIDE PANEL
   Remove the locking screw to open the side panel. Open the side panel more than 90 degrees and lift it up near the hinges.
   

INSTALLING MOTHERBOARD

Use the motherboard screws from the toolbox to install your motherboard on the pre-installed standoffs.

INSTALLING POWER SUPPLY

The power supply can be installed by opening the cable cover.

1. Open the Cable Cover.
2. Place the Power Supply.
3. Secure the Power Supply with 4x PSU screws.

INSTALLING A SECOND POWER SUPPLY

A second power supply can be installed by removing the cover in the rear panel.

1. Remove the rear PSU Cover.
2. Place the 4x rubber pads from the toolbox.
3. Place the Power Supply.
4. Secure the Power Supply with 4x PSU screws.

Configure your airflow-path with this overview. Some fan locations allow you to choose between storage or cooling to offer more flexibility.

The bottom radiator bracket is removed by loosening the thumb screw and sliding it forward.

CONNECTING THE FAN HUB

CONNECTING THE UNIVERSAL FAN HUB

1. HUB CONNECT THE FAN HUB 4-PIN INPUT CABLE TO YOUR MOTHERBOARD FAN HEADER
2. CONNECT EXTRA FANS TO THE CORRESPONDING CONNECTOR ON THE UNIVERSAL FAN HUB
3. CONNECT THE SATA CABLE TO THE POWER SUPPLY

INSTALLING DRIVES

2.5" SSD INSTALLATION
One SSD can be installed on the 3x dedicated SSD bracket and two on each of the 4x SSD covers.

3.5" HDD INSTALLATION
4x Phanteks Stackable 3.5" HDD Brackets are included.
Additional brackets are sold separately (PH-HDDKT_03).

MAIN COMPARTMENT
A total of 8 Stackable HDD brackets can be installed on the side fan positions. Before installation please remove the SSD Covers.

INSTALLING WATER COOLING

This overview shows all possible radiator form-factors, locations and clearances.

RADIATOR COMBINATIONS
Some radiator clearances depend on other hardware installed. Subtracting the radiator and fan thickness shows the remaining clearance for other radiators.

INSTALLING FILL AND DRAIN PORTS

We highly recommend installing a drain port and fill port for easy maintenance in the future.

A Fill port can be easily installed in the Top Panel with a Passthrough Fitting and a Stop Fitting. The port diameter is 20.5mm.

Phanteks Passthrough fitting:
PPH-PTF_BK/CR_G/4

Phanteks Stop fitting:
PH-PG_BK/CR

The Drain Port is installed in the Front Panel using a Passthrough Fitting and a Stop Fitting / BallValve. The port diameter is 20.5mm.

Phanteks Passthrough fitting:
PH-PTF BK/CR_G1/4

Phanteks Stop fitting:
PH-PG_BK/CR

Phanteks Ball-Valve fitting:
PH-BVA_BK/CR_G1/4

INSTALLING GPU ANTI-SAG BRACKET

To prevent your GPU from tipping down you can install the GPU Anti-Sag Bracket.

INSTALLING GPU ANTI-SAG BRACKET

1. INSTALL ALL GPU AND PCl CARDS
2. PLACE THE GPU ANTI-SAG BRACKET
3. INSERT THE THUMBSCREWS WITHOUT TIGHTENING THEM
4. PRESS DOWN AND LOCK THE THUMBSCREWS IN POSITION.

Always loosen the 2 thumb screws before removing any GPU or PCl cards.

Hold the GPU in the correct position when tightening the thumb screws.

CONNECTING FRONT I/O

Please consult the motherboard manual for additional instructions.

Please make sure to consult your motherboard manual before connecting the front I/O.

LIGHTING CONTROL

The Digital-RGB lighting can be easily controlled with the 2 buttons on the front of the chassis.

CABLE MANAGEMENT

Use the double-loop Velcro ties to route your cables. Zip ties are included in the accessory bag to manage any excess cables.

DUST FILTERS

The Enthoo 719 is equipped with a front, bottom, side, top and PSU filter. We recommend to clean these filters every month to keep your cooling performance optimized.

OPTIONAL UPGRADES

3.5" STACKABLE HDD BRACKETS
PH-HDDKT_03

For 3.5" or 2.5" Drive Upgrade up to 6x additional 3,5"HDDs with the optional HDD brackets. Contains 2x Stackable HDD Brackets.

INSTALLING A VERTICAL GPU

There are 2 vertical GPU positions available for System 1. We recommend the first position using the Vertical GPU Bracket.

1. INSTALL USING THE VERTICAL GPU BRACKET
   Vertical GPU Bracket sold separately (PH-VGPUKT_02)
   
   Follow the instructions with the Vertical GPU Bracket.
2. INSTALL USING THE RISER CABLE ONLY
   Riser C able soldseparately (PH-CRS_FL22)

INSTALLING A 5.25" BAY

1. INSTALL ANY 5.25" DEVICES INTO THE 5.25" BAY FIRST
2. PLACE THE 5.25" BAY INTO THE CHASSIS AND SECURE WITH 3X PSU SCREWS
   

INSTALLING A DUAL SYSTEM

1. REMOVE THE PRE-INSTALLED PSU BRACKET
   
2. INSTALL THE DUAL-SYSTEM BRACKET
   

4. CONNECT THE POWER BUTTON AND POWER LED TO THE MOTHERBOARD
   
   

INSTALLING A DUAL SYSTEM GPU

1. INSTALL RISER CABLE ON THE VERTICAL GPU MOUNT
   Riser Cable soldseparately (PH-CBRS_FL15)
   

2. INSTALL VERTICAL GPU MOUNT WITH 2 X SCREWS
   

TheGPU Mount has two mounting positions. Position A allows for better air cooling and 3-slotGPU cards.

Depending on your needs, it's not always necessary to install a GPU for your second system when your CPU is equipped with an integrated GPU.

CONTACT US

CUSTOMER CARE
RMA AND TECHNICAL SUPPORT INTERNATIONAL
Email: support@phanteks.com
Facebook: @Phanteks

RMA AND TECHNICAL SUPPORT AMERICAS
Hours: Monday-Friday 9:00 - 5:00 PST
Phone number: +1 (909)598-2115
Email: support@phanteksusa.com
Facebook: @Phanteks

For up-to-date information please check www.Phanteks.com

DURATION OF WARRANTY:

1. Fans -5 years
2. I/O Ports - 2 years
3. Fan Hub -2 years
4. LED Lighting - 2 years
5. Buttons - 2 years
6. Chassis- 5 years
7. Front and Top Panels - 5 years

Please check www.phanteks.com/Warranty for more information.

Documents / Resources

References

• Phanteks – Elevating Design and Performance
• Warranty – Phanteks

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Phanteks Enthoo 719 - PC Case Manual