ANTIFERENCE REMOTELINK A200 pro Series Quick Start Manual page 2

Fitting the amplifier
The A200 pro series of amplifiers are mains powered and are intended for indoor use only. These amplifiers are designed for continuous use. Do not locate
these amplifiers where they may come into contact with moisture or sources of heat.
The A200 pro series would normally be located in a roof space but care must be taken to ensure that they are well ventilated and kept clear of any insulation
material. A roof space can get extremely hot in the summer! Always ensure free ventilation and avoid covering the unit with soft furnishings when installed in a
living room.
Always securely mount the amplifier on a wall or fixed board that allows easy routing of the cables. Do not allow the unit to hang on its cables as this may
damage the connections or the circuit board. Do not cut off the moulded mains plug and directly wire these units to the mains supply. These units are fused
at 3 amps.
Once a convenient location has been selected mount the unit with screws by the fixing lugs provided on the housing. Route all of the cables and fit the F-
connectors.
Connect a VHF/FM, VHF/DAB or VHF BIII aerial to the VHF input (85-230MHz). Connect a suitable UHF TV aerial to the UHF input (470-790MHz).
Screening and accessories
All digital installations should be installed using double screened coaxial cables and screened accessories only. Digital
signal integrity and immunity to impulse noise cannot be guaranteed without adequate screening.
Antiference offer a full range of fully screened accessories. Ask your local distributor to advise you on the full
Antiference range or visit our web site for further information.
We recommend using Antiference SW700 or SW710U/V fully screened outlet plates to protect the signals right to the
back of the TV or digital set-top box.
Fitting F-Connectors to the cable
Fit either a professional crimped F-connector with the correct tool, or a "twist-on" F-connector following the dimensions
in the diagram opposite. Strip 10mm of the plastic cable sheath to expose the screening braid (fig.2). Fold the coaxial
braid back over the cable sheath neatly and evenly (fig.3). Remove any foil screening to expose the dielectric. Trim the
dielectric to expose a maximum 8mm of centre conductor (fig.4). Do not allow the centre conductor to exceed 8mm as
it may short inside the F-female on the amplifier. Fit the F-connector. Check that there are no whiskers of braid shorting
the centre conductor.
No. of Inputs
No of Outputs
Frequency Range MHz
Return Path Frequency
Gain ± 2dB
Noise Max. dB
Isolation between outputs
Impedance
Max. Output dB V
Mains Power with Red LED
Antiference reserves the right to change or alter specifications and features without prior notice. E&OE.
Antiference ©2013. The contents of this instruction leaflet are copyright. Copying or reproduction of any pictures or text is forbidden without prior
permission.
Antiference Ltd Fradley Distribution Park , Wood end Lane, Fradley Park, Lichfield, Staffordshire, WS13 8NE
A120D A240D
1 2
2 4
45-790 MHz 45-230 470-790
8dB 8dB
<3.5dB <3.5dB
>20dB >20dB
78dB V 78dB V
TEL : 01675 465487
A260D A280D
2 2
6 8
45-230 470-790 45-230 470-790
5-30 MHz
8dB 8dB
<4dB <4dB
>20dB >20dB
75
78dB V 78dB V
230V AC ±10% 50 Hz fitted Mains Plug BS1363
www.antiference.co.uk sales@antiference.co.uk
10mm
10mm
8mm
Max
A2120D A2160D
2 2
12 16
45-230 470-790 45-230 470-790
8dB 8dB
<5dB <5dB
>20dB >20dB
78dB V 78dB V
fig.2
fig.3
fig.4
fig.5