Related Manuals for NESTLE Nescafe FTP 30 E
Summary of Contents for NESTLE Nescafe FTP 30 E
- Page 1 type: T.TOP 05N Installation and maintenance manual Translation of the original instructions in Italian language Only for Nestlé Professional trained ® & approved Technicians MAN2100404F rel. 00 dated 05.12.2023...
- Page 2 FTP/FTS 30/60 E Ù MAN2100404F rel. 00 FTP_FTS_30_60 E V3_GB.docx 12/2023 Pag. 2/52...
- Page 3 FTP/FTS 30/60 E 05.12.2023 First issue Full rel. date description this document is made available electronically on the www.rheavendors.com site Please print this manual only if necessary; environmental protection is our common interest. MAN2100404F rel. 00 FTP_FTS_30_60 E V3_GB.docx 12/2023 Pag.
-
Page 4: Table Of Contents
FTP/FTS 30/60 E Index General information ..........................6 1.1. Intended use ............................6 1.2. Storage of the manual ........................6 1.3. Serial number label ........................... 7 1.4. Conformity mark ..........................7 General safety instructions ........................8 2.1. Symbols of danger ..........................8 2.2. - Page 5 FTP/FTS 30/60 E 10.1. Cleaning and sanitising the vending machine and its parts in contact with foodstuffs ....34 10.2. Cleaning and sanitising internal components ................. 35 10.3. Start up ............................35 10.4. First rinsing ............................36 11. First installation procedure ........................37 11.1.
-
Page 6: General Information
FTP/FTS 30/60 E 1. General information This machine is intended for professional use only, the correct operation of the vending machine occurs indoors under normal environmental conditions and at a room temperature between 5 °C and 35 °C, the relative humidity below 80%. The vending machine is intended to dispense prepared drinks only, by mixing food products with water (espresso coffee by infusion) to use food products declared by the manufacturer suitable for vending in open canisters, any other use is improper and it may cause accidents. -
Page 7: Declaration Of Conformity
FTP/FTS 30/60 E Silver serial number labels are applied inside and outside the cabinet of the vending machine, they supply the following information: 1 Type of the machine 2 Model of the vending machine and configuration 3 Rating plate with power supply voltage and hydraulic supply 4 Manufacturer 5 Vending machine code - production date and serial number 6 Country of manufacture... -
Page 8: General Safety Instructions
FTP/FTS 30/60 E 2. General safety instructions Before using the machine, carefully read this information that helps you behave properly and guarantees a safe use; the following pages use the symbols listed here below, whose meaning is of attention: GENERAL if the text is highlighted by this symbol, it is recommended to pay special attention to the performance of the procedures described;... -
Page 9: Safety Standards For Maintenance
FTP/FTS 30/60 E The machine shall be installed according to the laws in force in the Country of operation; pay special attention to the rules about the machines directly connected with the hydraulic network. Pay special attention to the chapters and notes highlighted by the symbols of alert and strictly observe the rules concerning the technicians’, operators’, and users’... -
Page 10: Residual Risks
FTP/FTS 30/60 E A residual risk is understood as a potential danger that cannot be eliminated and persists despite all precautions in use since it is related to the intrinsic features of the product, and it also includes non-identifiable risks. The actions and behaviours listed here below are intended to reduce residual risks and you shall always adopt them when interacting with the machine. -
Page 11: General Guarantee Conditions
FTP/FTS 30/60 E 3. General guarantee conditions These conditions regulate Rheavendors Industries S.p.A.’s obligations with reference to guarantee and repair; any other term or condition, either verbal or written, is not applicable, including those in the purchaser’s purchase orders, if not explicitly accepted and signed by Rheavendors Industries S.p.A.; if the guarantee terms here below should be held not to be valid and/or lawful in the Country where the product is sold, they will not be effective whereas all the other clauses will remain valid and applicable. -
Page 12: Technical Data Of The Vending Machine
FTP/FTS 30/60 E 4. Technical data of the vending machine DIMENSIONS FTP / FTS 30 FTP / FTS 60 Height 640 mm 668 mm 318 mm Width 422 mm 544 mm 568 mm Depth Depth with front door opened 770 mm 880 mm NET WEIGHT FTP 30 E... - Page 13 FTP/FTS 30/60 E HEATING ELEMENT Instantaneous water heater through a magnetic induction system 2,900 W GRINDER Conical millstones. Motor 230 V dc ESPRESSO COFFEE BREWER Ø45 mm, variable-volume brewing chamber ground capacity 8 ÷ 14 gr Ø36 mm, variable-volume brewing chamber ground capacity 6 ÷...
-
Page 14: Tolerance Values
FTP/FTS 30/60 E In 30 max. two instant, in 60 max. four instant, according to the machine configuration; single (55 mm) and double (110 mm) width; dispensing worm screws 9 mm or 18 mm in pitch; with mixer gear and product shaker, if arranged by the configuration and with standard or shorter product chute outlet: - instant canister capacity: STANDARD CANISTERS height 190 mm... -
Page 15: Product Canister
FTP/FTS 30/60 E Possible configurations are numerous and they are coded by categories exemplified here below in the abbreviation of the machine: espresso instant products and coffee beans two espresso instant products and two different coffee beans product canisters number of instant products and coffee beans water supply external, by means of the inlet solenoid valve E3 R... -
Page 16: Accessories
FTP/FTS 30/60 E V.M. FTP/FTS 60 E5 R2 MVH V.M. FTP/FTS 60 EE5 R2 1500 grams grams grams coffee coffee beans 1 beans 2 coffee beans § § VSF18 VSF18 VSF9 VSF18 VSF9 VSF9 VSF18 water 1 water 2 water 1 water 2 water 3 water 3... -
Page 17: Installation
FTP/FTS 30/60 E 5. Installation Upon receipt of the vending machine make sure that it has not been damaged during transport. If you should find out any damage, immediately make a complaint to the carrier: the package shall be intact, it shall show no sign of alteration, dent, impact, deformation, breakage, wetted area or sign that may indicate that the package has been exposed to rain, frost or heat. -
Page 18: Positioning
FTP/FTS 30/60 E When installed in its workplace, the vending machine shall be positioned in a room protected against atmospheric agents: it is not suitable for installation outdoors. It shall be installed in dry rooms at a temperature between 5 °C and 35 °C and it can’t be installed in environments where you use water jets for cleaning (e.g. -
Page 19: Hydraulic Connection
FTP/FTS 30/60 E Observe the laws on connections with the hydraulic network in force in the Country of operation. The water used to supply the vending machine must have all the features suitable for human consumption, let water come out of the hydraulic network until it is clear and free of any trace of dirt. Make sure that the pressure of the network is the one required for the machine and use a pump or a reducer in case of non-compliance;... -
Page 20: Description Of The Vending Machine
FTP/FTS 30/60 E 6. Description of the vending machine The vending machine is a machine designed for being used by all users since requiring no specific competence; to obtain the drink, insert the possible credit and press the key you wish for a short time. This manual is intended to describe the NESCAFÉ... - Page 21 FTP/FTS 30/60 E Front door panel FTP/FTS 30 E Front door panel FTP/FTS 60 E Inner view of the machine (example) Rear view of the machine (example) MAN2100404F rel. 00 FTP_FTS_30_60 E V3_GB.docx 12/2023 Pag. 21/52...
- Page 22 FTP/FTS 30/60 E Inner view of the machine (example) Rear Inner FTP/FTS 30 E (example) Rear Inner FTP/FTS 60 E (example) MAN2100404F rel. 00 FTP_FTS_30_60 E V3_GB.docx 12/2023 Pag. 22/52...
- Page 23 FTP/FTS 30/60 E 01 - Door lock: the door is closed by means of a lock; the key is mapped and numbered for identification. 02 - Selection keyboard: in FTP, after closing the door, press the buttons to dispense; the button will turn on during the dispensing cycle;...
- Page 24 FTP/FTS 30/60 E 14 - Door switch: it powers off the machine when the door is open. Service key: Use the service key to supply the vending machine if it is necessary to activate the machine when the door is open. Attention some parts remain live any way: act with the utmost caution.
-
Page 25: Electronics
FTP/FTS 30/60 E 7. Electronics MAN2100404F rel. 00 FTP_FTS_30_60 E V3_GB.docx 12/2023 Pag. 25/52... -
Page 26: Cpu
FTP/FTS 30/60 E The CPU board, housed on the rear of the machine and secured to the frame by means of support turrets, governs the machine operation and it is intended to operate the machine devices. Power supply IN 230 V ac Solenoid valves / mixers Double USB-A socket (RS485) Product motors... -
Page 27: Induction Board
FTP/FTS 30/60 E The induction board, placed on the right side of the machine and under the logic control of the CPU, is used to properly supply the transducer of the magnetic induction system, thus heating the dispensing water flowing in a coil;... -
Page 28: Display / Gpu Board
FTP/FTS 30/60 E The display / GPU board - secured inside the door - receives the signals from the selection keyboard and it displays the messages; a flat cable is intended to connect it with the CPU for signal exchange. The internal programming button is installed on the printed circuit of this board, which is also providing for the illumination of the keyboard. -
Page 29: Tft In Ftp
FTP/FTS 30/60 E 7.5.2. 3.5” TFT in FTP Input 5 V dc to CPU (J5) Door lighting Input power supply 24 V dc to CPU (J4) Double USB-A socket (RS485) Connector controller touch screen Lighting of selection keys Keyboard connector Lighting of selection keys Cup station lighting Lighting of selection keys... -
Page 30: Water Heating
FTP/FTS 30/60 E 8. Water heating The Varitherm device is an instantaneous water heater through a magnetic induction system, protected and controlled by a safety thermostat manually resettable and by a temperature probe. A vibration pump with by-pass conveys water to the magnetic inductor, the recirculation solenoid valve, the instant solenoid valves and the three-way valve for espresso. -
Page 31: Hydraulic Diagrams
FTP/FTS 30/60 E 9. Hydraulic diagrams The hydraulic diagrams of the vending machines are supplied here below. The following table describes the meaning of the symbols mentioned by the diagrams. symbol description Water inlet solenoid valve Air break Volumetric counter Vibration pump By-pass Drain tap... -
Page 32: Hydraulic Diagram Ftp 30 E / Fts 30 E
FTP/FTS 30/60 E MAN2100404F rel. 00 FTP_FTS_30_60 E V3_GB.docx 12/2023 Pag. 32/52... -
Page 33: Hydraulic Diagram Ftp 60 E / Fts 60 E
FTP/FTS 30/60 E MAN2100404F rel. 00 FTP_FTS_30_60 E V3_GB.docx 12/2023 Pag. 33/52... -
Page 34: First Installation Of The Machine
FTP/FTS 30/60 E First installation of the machine After unpacking the vending machine, placing it firmly at the workstation as well as providing for its water and energy connection, carry out some actions for its functionality. Wash your hands carefully with water and soap before handling the machine and the products;... -
Page 35: Automatic Reset
FTP/FTS 30/60 E Prepare a chlorine-based anti-bacterial sanitising solution by observing the instructions supplied with the product; after disassembling and removing, put the product canisters, the mixing bowls of mixers, their fans and the silicone tubes for dispensing products into the solution; the time necessary to sanitise is specified by the anti-bacterial product package;... -
Page 36: First Rinsing
FTP/FTS 30/60 E At the end of assembly and final inspection, the water used for testing is discharged from the machine; as soon as the machine is powered on for the first time, all circuits must be filled in before any other action; after all hydraulic circuits of the machine have been filled, the water flow stops automatically. -
Page 37: First Installation Procedure
FTP/FTS 30/60 E First installation procedure Use this procedure to fill the water circuit on next power on. To perform the first installation, in FTP, press “1= PROGRAMMING”, scroll by means of key “2” to “MISCELLANEOUS”, press “1” and scroll by means of key “2”... -
Page 38: Coffee Brewer Clean/Rinse Cycle
FTP/FTS 30/60 E Attention the vending machine is supplied and running to all effects, the mobile parts of the coffee brewer will be handled. act extremely carefully. After placing a cup under the product nozzles, in FTP press 8=hc, in FTS press “START CLEANING BREWER”... -
Page 39: Vending Machine Loading
FTP/FTS 30/60 E Vending machine loading To load instant products, it is recommended to extract each canister. To load coffee beans, close the baffle before extracting the canister. Lift the covers of each canister and pour the product according to the content of the machine configuration, make sure that there is no lump and avoid compressing the product. -
Page 40: Maintenance
FTP/FTS 30/60 E Maintenance The time interval of cleaning operations largely depends upon the number of dispensing cycles and the hardness of water in use (use a softening system) and it must be adjusted to the working conditions of the vending machine. -
Page 41: Monthly
FTP/FTS 30/60 E • Machine walls and bottom Remove any trace of residue from the internal surfaces of the machine and clean with a damp cloth. • Internal door wall Remove any trace of residue from the internal surfaces of the door, above all in the proximity of the cup station. -
Page 42: Yearly
FTP/FTS 30/60 E • Dispensing system Replace the gasket at the bottom of the mixing bowl of the mixer; extract the mixer motor fan by pulling it and replace the gasket of the mixer motor shaft. • Product canisters Disassemble the product canisters on the machine; empty them, disassemble them in their basic components and clean them carefully. -
Page 43: Solution Of Problems
FTP/FTS 30/60 E Solution of problems Some events occurring during the operation of a machine may partially or totally compromise operativity. To help the operator restore the normal functionality of the vending machine, the display shows an error code, summed up by an abbreviation, pointing at the compromised function and providing support for the compromised function or device. - Page 44 FTP/FTS 30/60 E OFF 7 R recirculation Error in the water recirculation phase. check the functionality of the volumetric counter. OFF 8 coffee brewer during reset or start- Check the functionality of the coffee brewer, it must move freely; check the up cycle components of the gear motor: motor, pulleys, belt: check the encoder board, the (small letters)
- Page 45 FTP/FTS 30/60 E OFF 8 P lower position not After brewing, the brewing chamber fails to reach the lower position. reached during descent OFF 8 Q maximum upper After grounds have been ejected, the brewing chamber fails to reach the upper position not reached position.
- Page 46 FTP/FTS 30/60 E OFF 42 coffee brewer it signals that the coffee brewer has dispensed such a number of espresso cups counter that it must be serviced; OFF 43 grounds counter the number of used coffee doses in the grounds container has achieved the maximum limit.
-
Page 47: Uninstallation
FTP/FTS 30/60 E Uninstallation Use this procedure to empty the water circuit of the vending machine (VM). To perform the uninstallation, in FTP: press “1= PROGRAMMING”, scroll by means of key “2” to “MISCELLANEOUS”, press “1” and scroll by means of key “2”... - Page 48 FTP/FTS 30/60 E The uninstallation procedure starts; water is dispensed from all nozzles in order to empty the water circuit. Shut down the Vending Machine at the end of the uninstall cycle. The VM will automatically execute the first installation during next VM reboot to fill the water circuit. The uninstallation procedure does not delete any previously set settings.
-
Page 49: Suspension Of The Service (Temporary Inactivity)
FTP/FTS 30/60 E Suspension of the service (temporary inactivity) If the machine should remain off for more than one week, for any reason, it is necessary to: • Empty the grinder completely by dispensing espresso coffee till an empty signal is sent out. •... -
Page 50: Out Of Service
FTP/FTS 30/60 E Out of service • Carry out the uninstallation cycle. • Disconnect the water and power supply. • Empty and clean the drip tray. • Remove and clean the grounds container. • Empty and clean the product canisters. •... - Page 51 FTP/FTS 30/60 E MAN2100404F rel. 00 FTP_FTS_30_60 E V3_GB.docx 12/2023 Pag. 51/52...
- Page 52 FTP/FTS 30/60 E July 2023 MAN2100404F rel. 00 FTP_FTS_30_60 E V3_GB.docx 12/2023 Pag. 52/52...
Need help?
Do you have a question about the Nescafe FTP 30 E and is the answer not in the manual?
Questions and answers