Advertisement
Quick Links
Advertisement
Related Manuals for Asus VIVOBOOK S5602Z Series
Summary of Contents for Asus VIVOBOOK S5602Z Series
- Page 1 ASUS VIVOBOOK S5602Z Series Repair Manual...
- Page 3 Service Overview • ASUS is not responsible for direct, indirect, intentional o unintentional damages resulting from improper installation and operation. • Carefully read through this Service Guide for a look at various components of the device before performing any service and repairs.
- Page 4 Pre-repair checklist • Read the entire manual before starting any service procedures and follow all instructions. • Back up the data on your device. • Place your device on a clean and stable surface. • Turn off your device. • Disconnect all connected peripherals and cables.
- Page 5 ASUS S5602Z Series Overview Top View Bottom View Right View Left View Back...
- Page 6 Components Top View ♦ K/B MODULE ASSY ♦ SPEAKER ♦ LCD COVER ASSY ♦ HINGE CAP ♦ CAM FPC ♦ SO DIMM AL MYLAR ♦ CP FFC ♦ HINGE ♦ USB A ABSORBER ♦ MAIN BOARD ♦ IO FFC ♦ FP FFC ♦...
- Page 7 Components Top View ♦ LED MYLAR ♦ CAMERA TAPE ♦ CP C-TAPE ♦ FFC CONDUCTIVE TAPE Back...
- Page 8 Components Bottom View ♦ OL LCD FRAME ASM (OLED Panel SKU only) ♦ K/B MODULE ASSY ♦ LCD COVER ASSY ♦ THERMAL MOD ASSY ♦ SSD PLATE ASSY ♦ LCD BEZEL ♦ BOTTOM CASE ASSY ♦ 16.0' OLED PANEL ♦ MAIN BOARD ♦...
- Page 9 Repair Overview This chapter describes disassembly and assembly (Assemble document please look up from the last page), please follow the information provided in this section to perform the complete disassembly procedure. ♦ Precautions: Before you perform any service or repair on the notebook, please pay special attention to the cautions prevent any damages to the notebook. 1.
- Page 10 Appropriate Tools Please prepare and select the appropriate tools to disassemble/assemble for the ASUS S5602Z Series notebook. ♦ Screwdriver ♦ Alcohol 95% ♦ Glove ♦ Dust-free Cloth Please accord to different screw specification to choose different screwdriver and head. ♦ Plastic Blade ♦...
-
Page 11: Bottom Case
BOTTOM CASE Disassembly Notice Step 1 : Remove screws *10pcs. Screws Spec Torque (kgf-cm) Step 2 : Use plastic blade to pry the Bottom Case. SCREW M2*8.5L+0.5 K W-NI T5 2.0±0.2 SCREW M2*4L+0.5 K W-NI T5 2.0±0.2 Start To avoid the bottom case hook, Please follow above arrow direction with using plastic blade to pry bottom don't insert plastic blade in each... - Page 12 DISCONNECT BATTERY CONNECTOR Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Before disassembly battery connector, please be sure to pull out adapter and disconnect the battery more than ten seconds in order to IC damage. Step 1 : Use the non-conductive pry tool to push iron sheet.
- Page 13 Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Release the Black Mylar from motherboard. Screws Spec Torque (kgf-cm) Step 2 : Remove the screw *1pc. Step 3 : Take away the SSD PLATE ASSY (with Black Mylar and Thermal Pad). SCREW M2*3L K B-NI #1 NY 2.0±0.2 Step 4 : Remove the SSD.
- Page 14 Assembly Notice Please be sure to pull out adapter and disconnect the battery. When installing the SSD, please keep the SSD less then 15 degrees with motherboard, and then insert the SSD. >15° <15° When installing SSD, please follow the steps below. 1.
- Page 15 Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Unlock and remove the RAM module. Remove (Front) (Rear) Back...
- Page 16 Assembly Notice Please be sure to pull out adapter and disconnect the battery. When assemble RAM, please follow below step. Paste DIMM ABSORBER on front and rear side of RAM Module. Step 1 : When absorber is fitted, follow the red line in the figure below to indicate the location. Step 2 : The up and down alignment can take Via as the positioning line, refer to the following figure, pay attention to the near PIN can not exceed the red circle Via to avoid short circuit.
- Page 17 BATTERY Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Before disassembly battery connector, please be sure to pull out adapter and disconnect the battery more than ten seconds in order to IC damage. Torque(kgf-cm) Step 1 : Remove the screws *5pcs. Screws Spec Step 2 : Take out Battery and then remove the Battery cable...
- Page 18 SPEAKER Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Disconnect the SPEAKER connector. Assembly Notice Step 2 : Remove SPEAKER. For Speaker assembly, please follow the layout below to tidy up cable. Disconnect For Speaker assembly, please follow the layout below to paste new acetate tape on speaker connector.
- Page 19 WIFI CARD Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Tear off the Tape. Screws Spec Torque (kgf-cm) Step 2 : Disconnect the WIFI Card RF Cables *2pcs. Step 3 : Remove screw *1pc (Red circle) and WIFI Card. SCREW M2*3L K B-NI #1 NY 2.0±0.2 Tear off...
- Page 20 Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Disconnect Fan connector *1pc. Screws Spec Torque (kgf-cm) Step 2 : Remove screw *3pcs (Red circle). Step 3 : Remove the Fan. SCREW M2*4L (K) B-ZN #1 2.0±0.2 Assembly Notice Please use the correct technique to take fans off to...
-
Page 21: Thermal Module
THERMAL MODULE Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Remove screws *4pcs (Yellow circle). Screws Spec Torque (kgf-cm) Step 2 : Remove the THERMAL Module. SCREW M2*3L K B-NI #1 NY 2.0±0.2 Recommend that the force point is at Green block, and pull up thermal module to take it out. -
Page 22: Main Board
MAIN BOARD Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Tear off the USB A ABSORBER. Screws Spec Torque (kgf-cm) Step 2 : Disconnect connector *6pcs (Yellow mark) . SCREW M2*3L K B-NI #1 NY 2.0±0.2 Step 3 : Remove screws *12pcs. - Page 23 MAIN BOARD Mainboard connector placement EDP CABLE POWER KEY IO BD FFC SPEAKER TP FFC BL FPC K/B FPC BATTERY Back...
- Page 24 MAIN BOARD Materials on mainboard CPU ABSORBER BOT TYPE C BKT ASSY TYPE A ABSORBER TOP MEMORY ABSORBER LED MYLAR SO-DIMM ABSORBER Back...
- Page 25 IO BOARD and TOUCHPAD Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Remove Tapes *5pcs (Green mark). Screws Spec Torque (kgf-cm) Step 2 : Remove screws *1pc (Red circle). SCREW M2*4L (K) B-ZN #1 2.0±0.2 Step 3 : Remove IO BOARD with FFC and then disconnect FFC cable (Red mark).
-
Page 26: Keyboard Module
KEYBOARD MODULE Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Remove CAMERA Tape *2pcs (Green mark). Screws Spec Torque (kgf-cm) Step 2 : Disconnect and remove FP FFC *1pc (Blue mark). SCREW M2*5L K B-ZN #1 NY 2.5±0.2 Step 3 : Remove screws *4pcs. - Page 27 KEYBOARD MODULE Assembly Notice Please be sure to pull out adapter and disconnect the battery. When assembly KEYBOARD Module, please follow the location below to tidy up When assembly the KEYBOARD Module, please follow the image below to tidy up EDP Antenna cables.
- Page 28 LCD BEZEL and HINGE CAP Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Use the plastic blade to pry HINGE CAP. Step 2 : Remove LCD BEZEL. Insert to Hinge Cap Pry open Step 2-1~2-4, Start from the middle area of each side of bezel, Using the forefinger to hold the outer edge firmly and the thumb flipping the...
-
Page 29: Lcd Bezel
LCD BEZEL Assembly Notice Please be sure to pull out adapter and disconnect the battery. When assembly the BEZEL, please follow below paste new BEZEL ADH BEZEL ADH TOP BEZEL ADH RL BEZEL ADH BOT Back... -
Page 30: Lcd Panel
LCD PANEL Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Pull out PANEL ADH SERV *2pcs. Screws Spec Torque (kgf-cm) Step 2 : Remove the screws *10pcs and then remove two hinges. SCREW M2.5*2.5L K B-ZN #1 NY 2.5±0.2 Step 3 : Remove LCD Panel. - Page 31 LCD PANEL Assembly Notice Please be sure to pull out adapter and disconnect the battery. When reuse the LCD COVER: Please paste new PANEL ADH SERV*2pcs. (New LCD COVER already contains PANEL ADHESIVE SERV *2pcs) PANEL ADHESIVE When assembly the LCD PANEL: Step 1 : Use the Mylar to reserve gap for upper and left side.
- Page 32 OL LCD FRAME (For OLED Panel) Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Release Mylar *2pcs (Blue mark). Step 2 : Pull out OL BKT Adhesive *4pcs (Red mark) slowly, and then separate panel. Release Please be careful during releasing OL BKT Adhesive to avoid OLED Panel broken.
- Page 33 OL LCD FRAME (For OLED Panel) Assembly Notice Please be sure to pull out adapter and disconnect the battery. When assembly OL LCD FRAME : When OL LCD FRAME assembly, please paste new OL BKT ADHESIVE before assembly panel. Step 1 : Remove release paper of BKT ADHESIVE *4pcs. Step 2 : Assembly and align the LCD panel to the upper side of OL LCD FRAME.
- Page 34 LCD COVER (with CAMERA& ANTENNA) Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Disconnect EDP Cable. Step 2 : Release Conductive Tape (Yellow mark) then lift up Camera, and release Tape then disconnect FFC (Green mark). Step 3 : Remove CAM FPC.
- Page 35 LCD COVER (with CAMERA& ANTENNA) Assembly Notice Please be sure to pull out adapter and disconnect the battery. For FDP Cable and ANTENNA Cables assembly, please follow the mark below to tidy up cables. When CAM FPC assembly, please follow the location below to tidy up FPC. When ANTENNA SET assembly, please follow the location below to assemble AUX&...
Need help?
Do you have a question about the VIVOBOOK S5602Z Series and is the answer not in the manual?
Questions and answers