Page 2: Table Of Contents
3.2 EggRider display specification 3.3 Pinout 3.4 EggRider display features 4. Firmware Update 4.1 EggRider Display Firmware Update 4.2 EggRider display firmware update from EggRider mobile app 5. Mobile App 5.1 EggRider mobile apps 5.2 Dashboard page 5.3 Search page 5.4 Rides...
Page 3 7.5 Kunteng (KT) Controller 7.6 Check compatibility 7.7 EggRider V2 Pinout 8. Troubleshooting 8.1 Solve mobile app connection problems 8.2 EggRider display speed shows --.- km/h 8.3 Settings Errors 9. Support 10. Road map 11. EggRider Release Notes 12. Disclaimer 13.
Page 4: Eggrider User Manual
1.1 Personalize your ebike ride EggRider is the fusion of an e-bike display with a mobile app, allowing you to enhance the performance of your e-bike ride. You can get your riding statistics and customize your riding profile.
Page 6: Eggrider Display Setup
Tighten the screw Allow slight rotation Please ensure the diameter of the handlebar is 22.2 millimeters and the handlebar is straight where you place EggRider display. When tightening the screw please allow some movement for display to rotate. - 6/112 -...
Page 7: Plug In The Connector To Your Bike
Do not make a connection if connectors are not the same type. Do not use unauthorized adapters such as female to female and male to male adapters because most likely they will burn the display and controller. - 7/112 - Copyright © 2019 EggRider.
Page 10: Protocol Detection
When you first connect the display it is important to check that speed shows 00.0 as shown in the picture bellow. This means the EggRider display is able to communicate correctly with your bike. If instead you see speed --.- or error FF (EFF) please follow Protocol not correctly setup in troubleshooting. Once the working protocol is found you should NOT change it from Display Settings page.
Page 12: Activation
Tap on the device in the search list. When the popup shows, choose option Activate now. Inserting correct information gives you instant activation. The following information is required: • Shop name - Insert the shop where you bought EggRider display from. Start typing and chose from the suggestions. Example: www.shop. eggrider .com eggrider •...
Page 13 Use the Battery Voltage drop down helper with predefined values for Voltage 0% and Voltage 100%. You can also manually adjust the values to your specific requirements. These settings are used for battery measurements only, they don't influence the voltage cutoffs for example. Use the controller specific settings for protection. - 13/112 - Copyright © 2019 EggRider.
Page 14: Saving Settings
Display Over Volt message please Stop using the display and Contact us via email. 2.6.3 Saving settings Warning The information on EggRider display it is only saved permanently when the display it is powered off from it's own power button. This also includes the trip data. 2.6.4 Configure e-bike specific settings One more step before you're set to go! On specific models you need to configure the e-bike/controller specific settings to have full functionality.
Page 16: Display
Down using layout v1/v2 toggles Road/OffRoad modes using layout v3 on main screen - cycles through dynamic menu using layout v3 on second screen - cycles through statistics Long press and combinations definitions...
Page 17 Power 3.1.2 EggRider V2 display screens EggRider display offers different screen layouts: v1, v2, or v3. See display settings how to change the layout. Screens layout v1/v2 Main screen layout v1...
Page 18 The layout v1 is used as an example to showcase all possible icons on the screen. Although the information is positioned differently, the basic icons remain consistent across layouts. See the descriptions below for more. - 18/112 - Copyright © 2019 EggRider.
Page 19 Assist Level - The assist level the motor provides • • Secondary Unit - It can be Power (W), Current(A), or Efficiency (watt per distance unit) • Time - Time of the day • Distance - Current trip distance - 19/112 - Copyright © 2019 EggRider.
Page 20 Range - Estimated distance remaining until the battery runs out Layout V3 The layout V3 is available with firmware and app version v2.7 and above. It provides more detailed data compared to the layouts V1 and V2. - 20/112 -...
Page 21 Wh used - Estimated energy consumption, calculated based on data from 10 or more trips. This reflects the full battery capacity utilization over time • Run Time - The total duration during which the bike was moving (speed > 0), displayed in hours, minutes, and seconds - 21/112 - Copyright © 2019 EggRider.
Page 22 Version - Firmware version of the display • Build - Firmware build number • MAC - EggRider device ID • Disp Temp - Temperature of the display in degrees Celsius • Disp Vol - The electrical voltage powering the display. If the voltage is too low or fluctuates significantly, it may indicate issues with the power supply or the display’s performance...
Page 23: Eggrider Display Specification
3.2 EggRider display specification 3.2 EggRider display specification SIZE 75mm x 47mm x 35mm WEIGHT CABLE LENGTH 50cm HANDLEBAR MOUNTING BRACKET Standard 22.2mm diameter CLAMP SCREW Hex bolt M3x10mm MOUNTING CLAMP PIN 2.0mm diameter and around 15mm length PHYSICAL BUTTONS...
Page 25: Eggrider Display Features
Detects real battery capacity and tracking stats of up to 3 batteries. EggRider mobile app available for Android and iOS. Easy configuration from the EggRider app. Ability to use the EggRider app as a larger display. In-depth charts capability for your rides. One button switch between two profiles •...
Page 26: Firmware Update
4.1 EggRider Display Firmware Update Attention It is highly recommended to ensure you update your firmware to the latest available when you receive your EggRider. Please make sure to put EggRider display in update mode when doing the update procedure!
Page 27 Because of the many changes in some of the core functionalities we recommend following the steps bellow for a smooth transition. We tested the update from firmware version >= v2.4.11. It should also work from older firmware versions but we recommend doing a reset to defaults afterwards.
Page 28: Eggrider Display Firmware Update From Eggrider Mobile App
4.2 EggRider display firmware update from EggRider mobile app 4.2 EggRider display firmware update from EggRider mobile app Attention It is highly recommended to ensure you have the latest firmware available on your EggRider display. Attention Available starting from app version 2.6.03 4.2.1 Steps to update...
Page 29 Tap on the latest sable version Update procedure will start When update is finished the EggRider display will start in normal running mode and the app will connect to Attention If the update hangs, power off from the battery or unplug the cable and restart procedure.
Page 30: Mobile App
5. Mobile App 5. Mobile App 5.1 EggRider mobile apps Both Android and iOS apps have the same functionalities, except for short periods of time between version releases. Although generally similar in appearance, there are some visual differences due to platform-specific components.
Page 36: Search Page
Accessible from menu Search It shows the list of EggRider displays in range. When the app starts, it scans for EggRider devices nearby and displays them in the list. You can also trigger the scan manually by pulling down on the page.
Page 37 If your device is not showing up in the list • Make sure the app has access to bluetooth under your phone's settings • Make sure the EggRider display is plugged in and turned on • Restart the EggRider display •...
Page 38: Rides
In the Rides page, on the top bar you have the following extra actions: • Delete Rides - It deletes all Rides with distance < 0.1 km • Get Display stats - Display Last Ride Stats - 38/112 - Copyright © 2019 EggRider.
Page 39 5.4.1 Ride Summary Rides are differentiated by the source labels. • App - Real-time information recorded by app when connected to EggRider display. (Tapping shows Ride summary). Ride recorded by the app • Display A (Auto) - At every connection the app collects automatically the last ride data recorded by display (Tapping shows Display stats).
Page 40 To go back to Ride summary, press the arrow in the left top corner (or button on android). Back 5.4.3 Display Stats Accessible from the Rides list page by tapping on a ride labelled with Display A or Display M. - 40/112 - Copyright © 2019 EggRider.
Page 41 These metrics might encompass information such as distance, duration, speed, energy consumption, and more, providing insights into each ride taken using the EggRider display. Battery labels - This section displays a trio of distinct columns, each dedicated to presenting detailed statistics specific to an individual battery.
Page 42: Display Settings
For each protocol type there are two options, one normal and one Rx/Tx Swap. The last one is to help when the communications wires are inverted. Info When set to Auto the display will try to autodetect the protocol at the next startup. - 42/112 - Copyright © 2019 EggRider.
Page 43 If set to Yes you can only change profile from OffRoad to Road and based on the option use the mobile app for both ways or also the display when the app is connected. - 43/112 - Copyright © 2019 EggRider.
Page 44 Attention Keep in mind that when you select lower than 9 assist levels, EggRider uses internally the levels beween () for pages like power levels or for the bafang basic assist levels. This is to allow changing the number of assist levels witouth altering the power levels.
Page 45 • Main screen v1 clearly shows Offroad/Road labels at the top of the screen. • Main screen v2 uses the assist level background color to differentiate modes - dark for Road and white for OffRoad. • Main screen v3 display OffRoad/Road labels and features a dynamic menu to toggle various parameters, such as power and range.
Page 46: Battery Settings
5.5.2 Battery Settings EggRider has up to 3 battery profiles. You can use these profiles to track stats independently if you have more than one battery. Please be sure you are setting at least the battery selected profile correctly. You can leave the other battery profiles as they are by default if not used.
Page 47 5.5.2 Battery Settings Attention Never connect EggRider to a battery bigger than 52V nominal. EggRider display works up to 60V when directly connected. With certain controllers we can overcome this limit by connecting to a 12V output. Info Battery voltage drop down is just a helper with predefined values for Voltage 0% and Voltage 100%. It is normal to go back to Select.
Page 48: Display Advanced Settings
Full battery (preferably just after disconnected from the plug) or a multimeter. Attention Please ensure that you have the right Voltage 0% and 100% relative to your battery which can be found in EggRider settings page. You can select from the drop down Select to auto-fill these values.
Page 49 Function used to permanently reset the ODO stats 5.6.6 ODO Offset Function used to set an offset to the ODO distance in case you want to have your old display distance in the odo total distance - 49/112 - Copyright © 2019 EggRider.
Page 50 5.6.7 ASI password 5.6.7 ASI password In case you have an ASI controller that has been locked with a password, you can insert the password here so that EggRider can still change the settings Last update: March 3, 2023 - 50/112 -...
Page 51: App Settings
Retry 30 seconds • Retry 1 minute • Retry 5 minutes • Retry 10 minutes • Retry 15 minutes 5.7.2 LOCATION Use GPS data Enabling this functionality offers altitude measurements in the ride stats. - 51/112 - Copyright © 2019 EggRider.
Page 52 • Dashboard v1 • Dashboard v2 - as Dashboard v1 plus live efficiency graphs, range and current values Range adaptability factor This value decides how fast the mobile app range estimation changes. A higher value will give more steadier estimation behavior while lower values will give range estimation values closer to the actual type of riding...
Page 53: Power Levels
5.8 Power levels 5.8 Power levels From app >= v2.5.03 and firmware >= v2.5.17 This page offers the possibility to adjust individually each assist level power and speed limit. It is used for ASI and Lishui controllers. Please see the e-bike specific pages for more information.
Page 54: Ebike Settings
After a successful write, the settings are stored in the display memory as well as in the app's memory. Doing this succesfully, settings will be visible even when the app is not connected. Last update: November 14, 2021 - 54/112 - Copyright © 2019 EggRider.
Page 55: Bafang
If you experience intermittent power cuts, it is most probably because you reach a speed limit or voltage cutoff. It can also be due to wrong configuration on the Pedal advanced settings. - 55/112 - Copyright © 2019 EggRider.
Page 56 E22 - BMS communication fault (22H) E23 - Light fault (23H) E24 - Light sensor fault (24H) E25 - Torque sensor torque signal fault (25H) E26 - Torque sensor speed signal fault (26H) E30 - Communication fault (30H) - 56/112 - Copyright © 2019 EggRider.
Page 58 BAFANG BBSHD 1000W CONFIGURATION EXAMPLES Disclaimer The following examples are for demonstration purpose only. The EggRider V2 display does not ensure legal compliance. Please check your local laws before riding to make sure you are riding legally and safely. - 58/112 -...
Page 59 1500w (not recommended to hold the throttle at 30A current draw for more than a few seconds) • 5 assist levels (can be set to 9 in the display settings) • throttle always full power (not based on the assist level selected on the display) - 59/112 - Copyright © 2019 EggRider.
Page 61 The controller will reject values outside its capabilities. Example of Bafang controller limits This can be found in the EggRider app About page. LOW BATTERY PROTECT (V) Value to prevent battery voltage cutoff (most likely your battery will have a BMS that will shut off power when the voltage gets too low).
Page 62 If Speed Limit is set to a value on Bafang Pedal or Bafang Throttle pages, then the percentage is from that value. If Speed Limit is set to Display command, then the percentage is from the Max Speed Road or Max • Speed OffRoad. - 62/112 - Copyright © 2019 EggRider.
Page 63 SPEED METER MODEL Options • External, Wheel Meter • Internal, Motor Meter • By Motor Meter SPEED METER SIGNAL The number of magnets per one wheel revolution, default 1. Last update: July 19, 2024 - 63/112 - Copyright © 2019 EggRider.
Page 64 For Assist 0 set Limited Current(%) = 100 and Limited Speed = 100 Your Pedal assist should work the same (speed and current limit) no matter what PAS level you see on display - 64/112 - Copyright © 2019 EggRider.
Page 65 Adjusts the amount of power that can be applied to each pedal rotation. The higher the number the greater the power applied to each rotation. This might affect at what rpm peak power sits in PAS operation, changing it doesn’t seem to be noticeable so we advise to leave it alone. - 65/112 - Copyright © 2019 EggRider.
Page 66 Some people report that setting this lower (as low as 5) may affect the startup delay on the throttle If you set this less than 10 on the v2 of the BBS02 controllers then your PAS will not work properly at all. On the older BBS02v1 controllers and the BBSHD controllers...
Page 67 For Assist 0 set Limited Current(%) = 100 and Limited Speed = 100 Your Throttle assist should work the same (speed and current limit) no matter what PAS level you see on display - 67/112 - Copyright © 2019 EggRider.
Page 68 You can set the max range to 42 which is the max input the controller accepts from throttle input 4.2v. If you set lower than this value your throttle response is not as linear or smooth as it could be. Last update: July 19, 2024 - 68/112 - Copyright © 2019 EggRider.
Page 69 These settings don't change when switching modes Road/OffRoad. They are changed only when programming from the app. Basic Settings BASE VOLTAGE ERROR VOLTAGE MIN (MV) ERROR VOLTAGE MAX (MV 0 SPEED BOOST TIME (X10MS) Delta Voltage (MV) Speeds Last update: July 19, 2024 - 69/112 - Copyright © 2019 EggRider.
Page 70: Lishui Settings (Lsw)
5. Voltage cutoff base The base under-voltage protection at controller. Options are • 21V - for 24V batteries • 31.5V - for 36v batteries • 42V - for 48v batteries - 70/112 - Copyright © 2019 EggRider.
Page 71 Value to fine tune the battery voltage cutoff. If your battery shuts down before reaching 0% this should be increased. You have to sum this value to the base cutoff voltage to get the actual voltage cutoff the motor will impose. - 71/112 - Copyright © 2019 EggRider.
Page 74: Eggrider V2 Mate X Settings
All mate X version have Lishui controllers. For information about each setting option please consult the Lishui settings page Attention If speed shows --.- km/h on EggRider display, please reset to default factory settings with the following procedure When the display is off, press until display turns on. (You should see Load default settings)
Page 75 If you want to increase the speed limit above 41 km/h, you can change wheel size to 16" on the Lishui settings page. This change will affect all speed limits. If speed measurements don't seem to be correct, please use wheel circumference from Display settings page to adjust. - 75/112 - Copyright © 2019 EggRider.
Page 77: Rad Power Bikes
Accesible from menu Lishui. The display protocol used should be Lishui or Lishui Rx/Tx. For more details, please see Lishui settings page. For model compatibility, please see rad compatibility list. The EggRider Rad version can have green or black connector but it is important to be a screw connector as shown in the pictures below. - 77/112 -...
Page 79 6.5.1 Rad settings Attention If speed shows --.- km/h on EggRider display, please see section protocol detection. Example Settings EggRider offers different type of strategies depending on your needs: • Current Limit • Running strategy Attention Ensure you adjust the Current limit to match your controller's specifications, which are usually listed on the controller label.
Page 81 The limits can vary from controller to controller so you might have to find the limits that work for you. • Speed limits for "Power levels" are taken from the EggRider display settings. - 81/112 - Copyright © 2019 EggRider.
Page 83 Attention If speed shows --.- km/h on EggRider display, ensure the connection to your bike is done correctly as shown above. If the issue continues, please see section protocol detection. Reset your display to initial settings RadV2 comes with pre-configured settings.
Page 84 This setting determines the maximum speed (in miles per hour, for example) that the Pedal Assist System (PAS) will provide. It sets an upper limit regardless of the PAS level selected. More settings definitions can be found ASI settings. - 84/112 - Copyright © 2019 EggRider.
Page 86: Kunteng Settings (Kt)
6.6 Kunteng settings (KT) Accessible from menu Kunteng Attention RadPower Bikes with a upgraded Kunteng controller are not compatible with EggRider display. Consists of one common settings section shared by both profiles Road and OffRoad and profile independent settings. Speed limits are used from EggRider display settings page.
Page 88 Options are 6 in, 8 in, 12 in, 14 in, 14 in, 16 in, 18 in, 20 in, 22 in, 24 in, 26 in, 700c and 28 in. 6.6.3 Kunteng Mode Specific Settings Low voltage cut-off (C12) OPTIONS • -2V () • -1.5V • • -0.5V • • +0.5V • • +1.5V • - 88/112 - Copyright © 2019 EggRider.
Page 89 • Stronger Throttle mode(P4-C4) Options • • 6km/h • 12km/h • Assist • Current limit (%) (C5) Options are 50%, 67%, 75%, 80%, 83%, 87%, 91% and 100%. Last update: July 19, 2024 - 89/112 - Copyright © 2019 EggRider.
Page 90: Asi - Accelerated Systems Inc Settings
For first time use please ensure to write ASI settings and power off display from button. Power At each press on EggRider display, the relative profile settings are written to the controller but they are not permanently saved on the controller. Required Asi controller configuration •...
Page 91: Start Sequence
Main Switch/key turn/press ON (power the controller) Press power button on the display (Turns ON EggRider) Stop sequence: Press power button on the display (Turns Off EggRider and also save settings/data) Main Switch/key turn/press OFF (cuts power to controller) CONNECTION FOR BAC500, BAC555, BAC800, BAC855 Mount a switch between ASI pins # 21 and # 22 or between your battery + pole and ASI pin # 22.
Page 92 Battery current limit (%) The battery current limit determines the maximum current that can be drawn from the battery. However increasing the battery current limit (e.g.100%-120%) may lead to faster and more robust torque assistance. - 92/112 - Copyright © 2019 EggRider.
Page 93 Field Weakening is a technique used to extend the maximum speed of the motor beyond its normal limits. The "Max 50%" indicates the maximum allowable weakening of the magnetic field, which can increase the motor’s speed but may reduce efficiency. Last update: July 19, 2024 - 93/112 - Copyright © 2019 EggRider.
Page 94: Eggrider Display Compatibility
7. EggRider display compatibility 7. EggRider display compatibility If you want to check compatibility with your bike please complete EggRider compatibility form. There are two main things to consider for compatibility: • Hardware - voltage, connector and pinout compatibility •...
Page 95: Compatibility List
7.2.2 Bafang mid drive motors Bafang mid-drive motors have 2 types of controllers based on the communication protocol UART communication - Compatible CANbus communication - Not Compatible UART display connector CANbus display connector - 95/112 - Copyright © 2019 EggRider.
Page 96 Bafang MM G340 • Bafang M300 • Bafang M400 7.2.3 Mate bikes Compatible with all Mate X versions. Please select Mate X EggRider version. Attention Mate classic bikes are not compatible with EggRider display. Bike compatibility list: • MATE X 250 •...
Page 97 EggRider is not compatible with RadPower bikes with upgraded Kunteng (KT) controllers. EggRider offers 2 different versions for RadPower bikes. If you are unable to find your specific bike model in the Rad and Radv2 lists below, please complete EggRider compatibility form.
Page 98 7.2.6 Radv2 7.2.6 Radv2 Compatible RadPower bikes feature 5-pin julet connector for display as shown below and use ASI controller: EggRider Radv2 is compatible with the following models: • RadCity 5 Plus • RadRhino 6 Plus • RadRover 6 Plus •...
Page 99: Accelerated Systems Controllers
Lishui LSW1497-2-1f Lishui LSW1659-14F 7.3 Accelerated Systems Controllers ASI controllers are compatible with EggRider V2 display if you have access to Bacdoor app. Please provide us picture with your display cable, battery voltage and controller model. - 99/112 - Copyright © 2019 EggRider.
Page 100: Cyc Motor
CYC motor X1 Pro Gen 2 with controller ASI BAC855 or BAC2000 • CYC motor X1 Stealth with controller ASI BAC855 7.5 Kunteng (KT) Controller Attention RadPower Bikes with a upgraded Kunteng controller are not compatible with EggRider display. 7.5.1 Other compatible bikes: • Aostirmotor S07-B •...
Page 101: Check Compatibility
7.6 Check compatibility 7.6 Check compatibility If you are still unsure and would like us to check compatibility, please complete EggRider compatibility form. • bike brand • bike model • year of manufacture • picture of controller label • picture of display connector - display side •...
Page 103: Troubleshooting
Open the app, give permissions and try to connect again 8.2 EggRider display speed shows --.- km/h EggRider display showing speed as --.-km/h or error FF (EFF) can be caused by the following reasons: Protocol is not correctly setup Communication port issue The display is not compatible with the connected controller 8.2.1 Protocol is not correctly setup...
Page 104 If none of the above works it is most likely because of the reasons 2) or 3). In this case please Contact us via email. 8.2.2 Communication port issue This is usually the case if EggRider was previously showing the speed correctly. The issue can be either on EggRider display or on the controller side. How to identify where the issue is? •...
Page 105: Settings Errors
If you see on the EggRider display the following error No ASI Settings please do the followings: Attention First, please make sure that you have the newest firmware version. You can update your EggRider display by doing the following Connect to the EggRider display...
Page 106: Support
You can use our EggRider users Facebook group for your generic questions or feedback. In this way everyone can see the response and benefit from it. It's really important that you check out EggRider issues page first. If you can't find your problem in the list above then you can Create a new issue (requires login).
Page 107: Road Map
Improving background stability • Predefined settings and settings sharing • Raising issues from the app • App multilingual support • Human power information for systems with torque sensor Last update: November 14, 2021 - 107/112 - Copyright © 2019 EggRider.
Page 108: Eggrider Release Notes
Latest stable releases: Please follow carefully the update instructions: Update instructions • EggRider Firmware v2.6.65 -> Release notes • EggRider App Android v2.8.03 -> Release notes • EggRider App iOS v2.8.03 -> Release notes Some known issues: • Accelerating while display is powering on results in wrong battery measurement •...
Page 109: Disclaimer
Disclaimer The EggRider V2 display does not ensure legal compliance. It does provide all the flexibility that the motor or controller can offer. The Road/Eco and OffRoad/Sport are merely 2 independently configured profiles. Please check your local laws before riding to make sure you are riding legally and safely.
Page 110: Frequently Asked Questions
12V output. EggRider specifications. Why do I get an alert even if I updated my EggRider: "Your EggRider display version (Unknown/v2.x.x) is lower than the supported version by the app (v2.x.x)?"...
Page 111 You get this notification if Lishui or ASI settings have not been configured yet. This is a common error that happens when you set up EggRider for the first time. In order to fix this please check our Troubleshooting Page .
Page 112 My connectors are both male? Please do not use female-to-female adapters. Wrong connection can damage the display or the bike and void your warranty. Contact us via email Last update: August 10, 2023 - 112/112 - Copyright © 2019 EggRider.

EggRider V2 User Manual

Quick Links

Need help?

Questions and answers

Related Manuals for EggRider V2

Summary of Contents for EggRider V2