Download
Share
Print this page
  1. Manuals
  2. Brands
  3. BETTER DESIGN Manuals
  4. Relays
  5. CL4-GSM-N/NC
  6. Instructions manual

BETTER DESIGN CL4-GSM-N/NC Instructions Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
CL4-GSM-N/NC Instruction
Ⅰ .Overview
+
GND 4 3 2 1
SIG
+
Input
interface
signal
indicator
front view
CL4-GSM
side elevation
Sensor2
Input
Sensor
interface
comtroller
COM1
COM2
N0 NC
N0 NC
N0 NC
COM1
COM2
COM3
N0 NC
N0 NC
N0 NC
①normally open
②com
③normally close
RoHS
COM3
COM4
N0 NC
+
COM4
N0 NC
+
1-4
outputs

Advertisement

loading
Need help?

Need help?

Do you have a question about the CL4-GSM-N/NC and is the answer not in the manual?

Questions and answers

Summary of Contents for BETTER DESIGN CL4-GSM-N/NC

  • Page 1 CL4-GSM-N/NC Instruction Ⅰ .Overview front view RoHS CL4-GSM comtroller COM1 COM2 COM3 COM4 N0 NC N0 NC N0 NC N0 NC side elevation COM1 COM2 COM3 COM4 GND 4 3 2 1 N0 NC N0 NC N0 NC N0 NC...

  • Page 2: Insert Sim Card

    output status indicator Power Sensor1 SET SW1 SW2 SW3 SW4 SIM card 9-12V DC Power Antenna Setting Sensor interface Card slot Ⅱ .Key and Indicator press the SET button, you can manually button mode to set master number GSM signal indicator, flash two seconds button to enter the GSM network Manual button, the output status will...

  • Page 3: Power Supply

    2.Power supply 9-12V DC Adapter （DC 5.5） Power Sensor1 SET SW1 SW2 SW3 SW4 SIM card 3.Connecting the GSM net-work The SIG light is on when the power is connected,controller will connecting the GSM net-work when SIG become flash 2 seconds after a short initialization time(about 50seconds).If SIG Flashing 2 seconds you can set and control the GSM controller.
  • Page 4 is SMS another is by dial 5.1.SMS settings mode Set the master number the instruetion fomat: SN+0000+SET+master number(Phone number) Send set RoHS instruction CL4-GSM comtroller Phone COM1 COM2 COM3 COM4 N0 NC N0 NC N0 NC N0 NC Receiveda set of successful SMS e.g.
  • Page 5 6.How to control GSM controller: SMS/Dial/ Button 6.1.SMS(ON /OFF/COM Command. T Command. L Command. XT Command) Send control RoHS commands CL4-GSM comtroller Phone COM1 COM2 COM3 COM4 N0 NC N0 NC N0 NC N0 NC Receiveda set of successful SMS Setup steps: (the default password for 0000) 6.1.1 ON command (open all relays and return temperature data)
  • Page 6 That SW1 will turn to ON, SW2 SW3 will turn to OFF, SW4 will be ignored. if operation is successful the device will return: SW1-4: NFFF; T1: 24.6C; T2: 16.9.C; H2: 28% 6.1.4 CHECK command (check the relays state and temperature data) The instruction format: SN+PASSWORD+CHECK Example: edit a messages and send SN0000CHECK...
  • Page 7 (SW1) and Sw2-4 is ignore. First GSM controller initial state is OFF, you send SMS: SN0000L120CXXX, then the state turn to ON and you will receive a SMS : SW1 IS INCHING. The ON state will be kept 120 minutes, after 120 minutes state turn to OFF.

  • Page 8: Button Control

    controlled), the master number can controll the relay1. The control modes divided into two kinds, one kind is jog mode, one kind is permanent flip mode. Jog mode set reference TX command. Jog mode is to get through the phone after the relay will be reversed, after setting the time to return to the original state, such as the call before the call is off the state, after the call is connected to a closed state, after setting the...
  • Page 9 − P/N: temperature plus-minus sign (P for + ,Nfor − Temperature value: from left to right is the hundreds, tens, ones and decimal places of temperature − Relay code: Nfor ON, F for OFF, X for ignore Example: send SN0000LEA01P0256NNNN Equipment to reply: TA1:LE +25.6C SW1-4:NNNN The reply means SW1-SW4 will all turn to on when the sensor1 temperature is below +25.6 °...
  • Page 10 − Relay code: Nfor ON, F for OFF, X for ignore. Example: send SN0000LEA01H030NNNN Equipment to reply: HA1:LE 30% SW1-4:NNNN SW1-SW4 will all turn to on when the sensor1 humidity is below 30%. Example: send SN0000GRB02H060FXNN Equipment to reply: HB2:GR 60% SW1-4:FXNN When the sensor2 humidity is above 60%, SW1 will be turn to OFF, SW2 will keep current state and SW3- SW4 turn to ON.
  • Page 11 Example: send SN0000CTBP10 You will receive SMS: CTB: +10 (it means the sensor2 temperature will be increase 1.0° C to be the correction value) Example: send SN0000CHAN05 You will receive SMS: CHA: -05 (it means the sensor1 humidity will be reduced 5% to be the correction value) Example: send SN0000CHBP12 You will receive SMS: CTB: +12 (it means the sensor2 humidity will be increase 12% to be the correction...
  • Page 12 7.5.Check temperature or humidity control Format:SN+password+GTS/GHS+**(**is group number, you can check 4 temperature/humidity groups by one SMS) e.g check the 1-4 temperature groups, SMS: SN0000GTS01, by the same way, to check the 5-8 groups, SMS: SN0000GTS05 check the 1-4 humidity groups, SMS: SN0000GHS01, by the same way, to check the 5-8 groups, SMS: SN0000GHS05 7.6.Delete temperature or humidity control...

  • Page 13: Factory Default Settings

    Power on reminder SMS: equipment is powered on. Power off reminder SMS: equipment is powered off. 9. Dial control receive feedback SMS set feedback SMS: SN+password+CBO [O is letter] cancel feedback SMS: SN+password+CBC [This funtion is default] In the default mode, no SMS will be received after dial control.If you want to receive a feedback SMS after dial control, you can send: SN0000CBO to GSM controller, receive: MESSAGE FUNCTION IS ON...
  • Page 14 12. MODE1 is default mode (works in most countries) When you are in the Nordic Europe or other a few countries found call works but SMS did not respond, change to MODE0. e.g. Send SMS: SN0000SM0 to equipment, then receive: MODE0 SET OK. When youwant to change to MODE1, sendSMS: SN0000SM1 13.
Save PDF