Related Manuals for WAREMA Lamaxa L50 Tex
Summary of Contents for WAREMA Lamaxa L50 Tex
- Page 1 Original instructions To be handed over to the operator. Please keep for future use. WAREMA fabric roof Lamaxa L50 Tex Operating and maintenance instructions Valid from 3 August 2023 Document number 2061955 [Rev. 4 – en]...
-
Page 2: Table Of Contents
Table of contents Table of contents Introduction........................3 Information on safety............................ 3 Information on the target group and application of these instructions............3 Explanation of signal words......................... 3 Basic safety instructions..........................3 Product information......................7 Intended use..............................7 Parts description............................9 Electrical data............................... -
Page 3: Introduction
These instructions are an integral part of the following product: Lamaxa fabric roof L50 Tex The instructions contain important information on the operation, care and maintenance of this item. They describe how to operate products with WAREMA standard drives. Other drives and special solutions are not dealt with. Permissible activities Performing tasks on the product that are not described in these instructions is not permissible. - Page 4 Introduction Possible risk during operation Incorrect operation can result in personal injury. The movements of the product can lead to crushing of the limbs. While the product is moving, do not reach between the moving parts. Do not reach into openings on the product while operating the product. Monitoring duty during operation Failure to monitor the product while it is moving may result in personal injury and property damage.
- Page 5 Lamaxa L50 Tex sun shading system variant The Lamaxa L50 Tex sun shading system variant is mounted without the inclination angle. The awning is not permitted to be extended in rain. There is a risk of water pocket formation. This may damage the awning and can pose a risk to people. In addition, moisture promotes wrinkling and waffling and causes impairment of the fabric.
- Page 6 Introduction Duty of supervision when not installed at ground level If the installation location of the roof system is on a balcony or a roof terrace, for example, special precautions must be taken for the GranTex with easyZIP guidance (if present) regarding the wind to ensure the safety of persons. The GranTex with easyZIP guidance is only able to withstand the loads associated with the specified wind speed limits (see Tab.
-
Page 7: Product Information
In addition, spray and splash water occur when moving the wet awning, depending on the weather The product is used to shade residential and commercial areas. The Lamaxa L50 Tex WeatherEdition variant is only approved for performance class 2 (precipitation quantity 56 l/m² per hour) with the awning fabric fully extended (see Chapter 2.5/Page... - Page 8 Product information Optional: GranTex with easyZIP guidance The product is an external sun shading system that is used for thermal protection, glare control and visual privacy on a carrier product e.g. Lamaxa fabric roof. The product reduces the incidence of light and optimises the use of solar energy. The product is intended to be used to protect against the sun, not the rain.
-
Page 9: Parts Description
Z angle bracket (on the side of the guide rails for fixing) Base plate Rain gutter (for WeatherEdition only) Beam Fig. 1: Parts description for Lamaxa L50 Tex fabric roof Electrical data Data for fabric roof Parameter Value Current consumption [A] 0.75-1.4... - Page 10 Product information Data for WMS Dimmer smart (if present) Parameter WMS Dimmer smart Operating voltage [V AC] 200-240 Frequency [Hz] 50-60 Load current [A] at 230 V AC Operating voltage [V DC] Switching capacity [W] at 24 V DC with WMS Dimmer smart 60 L (art. no. 2023455) Switching capacity [W] at 24 V DC with WMS Dimmer smart 100 L (art.
-
Page 11: Wind Resistance Roof System
Product information Data for WMS Dimmer 0-10 V (if present) Parameter WMS Dimmer 0-10 V Operating voltage [V DC] Power consumption [W] Frequency [GHz] 2.40-2.48 Degree of protection IP54 Safety class Operating and storage temperature [°C] -20 to +55 Tab. 5: Data for WMS Dimmer 0-10 V (if present) Wind resistance Roof system The product has the following resistance to wind loads: class 4 The declared performance only applies to the product itself. -
Page 12: Declaration Of Performance
Wind speed limits for awnings with easyZIP guidance in which the roof system (optional) is not installed at ground level (details in m/s) Declaration of performance The declaration of performance can be found at (www.warema.de/ce). Page 12 | 34 2061955 [Rev. 4 – en]/2023-08-03... -
Page 13: Operation
Operation Operation INFO Only operate the product if it is in technically perfect condition. Do not operate a product if it is damaged. Always contact the specialist dealer and protect the product against being operated as agreed with the specialist. Product with motor CAUTION Risk of crushing from failure to exercise care during operation. -
Page 14: Operating The Led Strip With The Wms Hand-Held Transmitter
Operation Operating the LED strip with the WMS Hand-held transmitter INFO Select the right channel for the product on the hand-held transmitter. The exact description of the hand-held transmitter can be found in the accompanying instructions for the hand-held transmitter. Press the UP button briefly . - Page 15 Operation without dimmer function Press the UP button briefly . The radiant heater is switched on. Press the DOWN button briefly . The radiant heater is switched off. 2061955 [Rev. 4 – en]/2023-08-03 Page 15 | 34...
-
Page 16: Incorrect Operation
Operation with dimmer function INFO The WMS dimmer 0-10 V changes the power of the connected radiant heater in 3 dimming levels. Level 1 Level 2 Level 3 100% Tab. 7: Radiant heater power at each dimming level The WMS dimmer 0-10 V switches the radiant heater power to 0% by default after 4 hours. The 4 hours restart every time the unit is operated. - Page 17 Operation Danger of crushing, shearing and entanglement While the product is moving, keep persons away from the product. While the product is moving, do not reach between the moving parts. Products operated by means of a control unit may start mov- ing at any time and without prior notice.
- Page 18 Operation Operation in windy weather (installation location not at ground level) awning with easyZIP guidance: If the installation location of the roof system is not at ground level, special precautions must be taken for the awning with easyZip guidance to ensure that people remain safe when it is windy.
- Page 19 Operation Operation in wet weather Applies to Lamaxa L50 Tex variant sun shading system. NOTICE Product damage from incorrect operation in rain! If the awning is not retracted in rain, water can collect in the fabric. Should it then become necessary to retract the awning (e.g.
- Page 20 Applies to Lamaxa L50 Tex variant WeatherEdition. The Lamaxa L50 Tex WeatherEdition variant can withstand normal rainfall (not including forecast/extremely heavy rain, hail etc.) only if the awning fabric is fully extended. If there are large amounts of precipitation, e.g. very heavy rain or hail, the awning must be retracted.
-
Page 21: Service
Use of the product in a manner that is not intended or failure to care for and check the product improperly render the product warranty from WAREMA void. Proper and regular cleaning and maintenance and the exclusive use of original spare parts are essential for trouble-free operation and a long product service life. -
Page 22: Cleaning, Care And Inspection Activities
Service Cleaning, care and inspection activities Over time, a film of dirt will form on the surfaces of sun shading products due to environmental influences. Due to the effects of solar radiation, this soiling can become permanently burnt into or stuck to the surface coating. These factors reduce the value and may ... - Page 23 The WAREMA cleaning agent for sun shading products can be used for metal and plastic surfaces and is certified by the GRM (Gütegemeinschaft Reinigung von Fassaden e.V.) (certification no. 142, 242, 342, 442, 542).
- Page 24 Aids required for cleaning: Whisk broom/brush (soft bristles) Vacuum cleaner (optional) Bucket Low-calcium water (recommendation) WAREMA cleaning agent for sun shading products (do not use on wood products) WAREMA cleaning glove Cotton cloth Additionally for awning fabric: Rubber eraser (non-marking)
- Page 25 Before you start, remove any objects that must not get wet. Performing detailed cleaning Prepare a bucket with water and WAREMA cleaning agent for sun shading products. Note the dosing quantities specified by the cleaning agent manufacturer. Wet the WAREMA cleaning glove.
- Page 26 Service Remove the detached soiling before drying. Cleaning the awning fabric without water In some cases, smaller spots and isolated dirty streaks can be cleaned without water. Dab off/strip away soiling with adhesive tape. and/or Remove soiling with a non-marking rubber eraser (by applying light pressure). Remove soiling with a vacuum cleaner if necessary (on the low setting).
- Page 27 Service Re-impregnating the awning fabric INFO The cleaning agent and fabric impregnation have opposing effects. By thoroughly rinsing off the cleaning agent with clear water, you can preserve the water-repellent property of the awning fabric for a longer time. Every time the fabric is cleaned, the original protective function of the awning fabric is slightly diminished. Depending on the fabric type, a reimpregnation can renew the water-repellent effect and is therefore recommended.
-
Page 28: Maintenance
When operating the product, check whether unusual noises can be heard from the cover panel. INFO To ensure proper functioning and your continued enjoyment of the product, WAREMA recommends having it professionally maintained once a year. Information on this can be obtained from your WAREMA contracting partner or at www.warema.de/service. -
Page 29: Repair
To ensure that your product continues to function properly, and to prevent the loss of its approved status, only use original spare parts. To order, contact your WAREMA dealer. What you should know about awning fabrics Technical fabrics may exhibit certain characteristics due to production and sizing that may appear to the operator to be "faults". - Page 30 Service Waviness in the seams and fabric panels As the fabric is wound onto and off of the shaft, it is tightened more at the hems, seams and panels than between the seams. The resulting tension in the fabric can lead to waviness (e. g. waffle or fishbone patterns) that "digs" into the fabric. The waves are visible when the unit is open.
-
Page 31: Dismantling/Disposal
A lack of appropriate knowledge when dismantling the product can lead to injuries and/or damage to the adjacent parts. Have the units dismantled by a qualified specialist. Dismantling of the product must be undertaken by a qualified specialist. Ask WAREMA for any missing documents before commencing maintenance. -
Page 32: Troubleshooting
Troubleshooting Troubleshooting INFO Problems described here without reference to a qualified specialist or certified electrician may be resolved independently. All other problems listed must be handled by a qualified specialist or certified electrician. Fault: The motor is not functioning. Cause Remedy Note The thermal protection switch on the... -
Page 33: Declaration Of Conformity
RoHS Directive 2011/65/EU: Directive on radio equipment 2014/53/EU (RED): Use for motor drives with an integrated radio receiver or for WAREMA components with an integrated radio receiver. Person in charge of the compilation of the technical documents: Elke Granzer; for address, see manufacturer. - Page 34 WAREMA Renkhoff SE Hans-Wilhelm-Renkhoff-Straße 2 97828 Marktheidenfeld Germany...
Need help?
Do you have a question about the Lamaxa L50 Tex and is the answer not in the manual?
Questions and answers