Advertisement
Quick Links
Advertisement
Related Manuals for Young Electric Mate R
Summary of Contents for Young Electric Mate R
- Page 2 P a rt s f o r b ik e ra c k P a rts f o r ra m p...
- Page 3 Semicircle Plate Parts List for bike rack Part# Description Rotating Group Parts List for ramp Bottom Fixing Bracket Part# Description M16*85 Outer Hexagon Bolt Ramp M16 Lock Nut Quick-release pin Beam Assembly Front Wheel Holder M10*25 Outer Hex Bolt Kit Required Tools（Not included）...
- Page 4 gap between the Bottom Fixing Bracket (2) and the Rotating STEP1 Group(1). Note: Do not overtighten the bolts to prevent the Bottom Fixing Bracket (2) and the Rotating Group (1) components from rotating easily. Align the Bottom Fixing Bracket(2) with the hole of the Rotating Group (1), insert the M16*85 Outer Hexagon Bolt (3) into the hole at the bottom, and then screw on the M16 Lock Nut (4).
- Page 5 STEP2 STEP3 Align the holes from the Front Wheel Holder (6) and the Beam Place the components assembled in steps 2 above into the Assembly (5). Then fix them with the M10*25 Outer Hex Bolt Bottom Fixing Bracket (2), align the holes, install 4pcs M10*120 Kits (7).
- Page 6 STEP4 STEP5 50Nm Insert the Middle Support Tube (10) into the base of the Bottom Install the adjustable Connecting Block (12) to the Middle Fixing Bracket (2), place the Semicircle Plates (20) on both Support Tube (10), then tighten the knob from the Connecting sides of Middle Support Tube (10), then fix them with the Blocks (12).
- Page 7 with the φ3.8 pin (15), making sure to place the pin through the STEP6 holes on the bolt. The diameter of lock beam should be less than 7mm. The lock is not included. 2" Align the holes of the folding tube with the holes on the vehicle’s 2’’...
-
Page 8: Folding Steps
Folding Steps ∶ · ∴ ∷... - Page 9 Bike Installation Instructions Snap the front tire of the ebike into the front wheel holder, place the rear tire in the beam, and then use the ratchet wheel straps to fix the front wheel, rear wheel, and seat/middle tube of the bike as shown in the figure below. Please place one bike on the side which is close to the vehicle first, and install the Connecting Block (12) after the bike is fixed.
- Page 10 Bike Installation Instructions（tire width<2.5”） If your tire width is less than 2.5”, please use velcros to fasten the front and rear tires. Only 4pcs of Velcros(19) are required to fix the tires, the rest are for spare. Please keep the fixing method of velcro the same for the bike on the other side.
- Page 11 How to Adjust the Wheel Cradle 1. Pull the cam gear 2. Turn in counterclockwise 3. Slide it 4. Until it against the tire 5. Fix by turning clockwise 6. Press it down...
- Page 12 How to Use the Ramp 1. Fix the buckle to the 2. Insert the ramp 3. Insert the 4. Fix the quick-release rack quick-release pin 5. Confirm the direction 6. Insert the ramp to the 7. Push the bike up of ramp bike rack along the ramp...
-
Page 13: Technical Specifications
⚫ Applicable for tires width within 5”, extra velcros (included) need to be applied for tires within 2.5” Model Name YOUNG ELECTRIC Mate R Description 2'' Hitch 2-Bike Rack with Ramp Material Aluminum & Steel Maximum Weight Capacity... - Page 14 ⚠ WARNINGS ⚠ ⚫ Do not overload beyond the bike rack’s weight capacity of 200lbs. ⚫ Do not carry more than 2 bikes on the carrier. ⚫ The bike rack is not intended for transporting humans or animals. If you are planning to load only one bike, it is recommended to place it in the position closest to the vehicle. ⚫...
- Page 15 Young Electric Warranty Policy Disclaimer of Liability: Repair or replacement of a defective Young Electric is committed to providing our customers with a product or the issuance of a refund or credit (as determined by quality shopping experience, for the products we sell, we provide Young Electric) is a purchaser’s exclusive remedy under this...
- Page 16 This manual contains warnings, cautions, and notes, therefore YOUNG ELECTRIC works hard to guarantee you a bike rack that please carefully read all of this information for your safety. Give is properly assembled and correctly adjusted when it leaves our special attention to any information that has a warning or factory.
-
Page 17: Get Support
Get Support https://youngelectricbikes.com support@youngelectricbikes.com Toll Free Number: 888-933-8899...
Need help?
Do you have a question about the Mate R and is the answer not in the manual?
Questions and answers
I have a young 2 e bike carrier 200lbs. How do I secure the adjustment support to the aluminum beam correctly. I tried a few times and the **** the block, any suggestions or can you send me a picture. Ty Mike