Panasonic LX-100 Series Instruction Manual

Panasonic INSTRUCTION MANUAL
Digital Mark Sensor LX-100 Series
MJE-LX100C No.0021-83V
Thank you very much for purchasing Panasonic products. Please read this Instruction
Manual carefully and thoroughly for the correct and optimum use of this product.
Kindly keep this manual in a convenient place for quick reference.
A WARNING
• Never use this product as a sensing device for personnel protection.
• In case of using sensing devices for personnel protection, use products
which meet standards, such as OSHA, ANSI or IEC etc., for personnel
protection applicable in each region or country.
□ specifications
\ Type Cable type Connector type
\ Model
NPN output
LX-101 LX-101-Z
Item
PNP output LX-101-P LX-101-P-Z
Sensing distance 10 ± 3mm
Supply voltage 12 to 24V DC±10% Ripple P-P10% or less
Current consumption
Normal mode: 750mW or less (Current consumption 30mA or less at 24V supply voltage)
E0C mode: 600mW or less (Current consumption 25mA or less at 24V supply voltage)
Teaching input
<NPN output type> <PNP output type>
Low (ON): 0 to 2V DC High (ON): 5V to +V DC
Source current 0.5mA or less Sink current 3mA or less
Input impedance 10kQ approx. Input impedance 10kQ approx.
High (OFF): 5V to +V DC, or open Low (OFF): 0 to 0.6V DC, or open
Output 1
(OUT)
<NPN output type> <PNP output type>
NPN open-collector transistor PNP open-collector transistor
■ Max. sink current: 50mA (Note 1) ■ Max. source current: 50mA (Note 1)
■ Applied voltage: 30V DC or less ■ Applied voltage: 30V DC or less
(between output 1 and OV) (between output 1 and +V)
■ Residual voltage: 1.5V or less ■
Residual voltage: 1.5V or less
[at 50mA (Note 1) sink current] [at 50mA (Note 1) source current]
Output operation
Mark mode: Light-ON / Dark-ON Auto-setting method on teaching,
Color mode: Coincidence-ON / Non-coincidence-ON
Short-circuit protection
Incorporated
Output 2 (Inversion output)
(OUT)
<NPN output type>
NPN open-collector transistor
■ Max. sink current: 50mA
■ Applied voltage: 30V DC or less
(between output 2 and OV)
■ Residual voltage: 1.5V or less
(at 50mA sink current)
<PNP output type>
PNP open-collector transistor
■ Max. source current: 50mA
■ Applied voltage: 30V DC or less
(between output 2 and +V)
■ Residual voltage: 1.5V or less
(at 50mA source current)
—
Output operation Inverted operation of the output 1
—
Short-circuit protection
Incorporated —
Response time Mark mode: 45
u
s or less, Color mode: 150 ju s or less
Operation indicator
Orange LED (lights up when output 1 is ON)
MODE indicator 'RUN': Green LED, 'TEACH', 'ADJ', 'COLOR1, 'TIMER', 'PRO': Yellow LED
Digital display 4 digits red LED display
Sensitivity setting Mark mode: 2-level teaching / Full-auto teaching, Color mode: 1-level teaching
Fine sensitivity adjustment function
Incorporated
Timer function Incorporated OFF-delay timer / ON-delay timer, switchable either effective or ineffective
Protection IP67 (IEC)
Ambient temperature -10 to +55°C (No dew condensation or icing allowed), Storage: -20 to +70°C
Ambient humidity 35 to 85% RH, Storage: 35 to 85% RH
Emitting element Red / green / blue LED
Material
Enclosure: PBT, Display: Polycarbonate, Operation buttons: Silicone rubber, Lens: Glass
Cable
0.2mm2 5-core cabtyre cable, 2m long —
Weight
120g approx.
55g approx.
Notes: 1) The connector type
LX-101D-Z
is 100mA.
2) The connecting cable is not supplied as an accessory for the connector type
LX-101 LH-Z.
Make sure to use the optional cables with connector below:
CN-24B-C2
(Straight type, 4-core, Cable length: 2m)
CN-24BL-C2
(Elbow type, 4-core, Cable length: 2m)
CN-24B-C5
(Straight type, 4-core, Cable length: 5m)
CN-24BL-C5
(Elbow type, 4-core, Cable length: 5m)
—43.5mm |-*—
snb
\014mm
05mm
-H 31mm
05mm
=
1
^
□ cautions
This product has been developed / produced for industrial use only.
Make sure to carry out wiring in the power supply off condition.
Take care that wrong wiring will damage the sensor.
Verify that the supply voltage variation is within the rating.
Take care that if a voltage exceeding the rated range is applied, or if an AC
power supply is directly connected, the sensor may get burnt or damaged.
In case noise generating equipment (switching regulator, inverter mo¬
tor, etc.) is used in the vicinity of this product, connect the frame ground
(F.G.) terminal of the equipment to an actual ground.
If power is supplied from a commercial switching regulator, ensure that the frame
ground (F.G.) terminal of the power supply is connected to an actual ground.
Do not use during the initial transient time (0.5 sec.) after the power supply is switched on.
Take care that short-circuit of the load or wrong wiring may burn or damage the sensor.
Do not run the wires together with high-voltage lines or power lines or put
them in the same raceway. This can cause malfunction due to induction.
Take care that the sensor is not directly exposed to fluorescent light
from a rapid-starter lamp or a high frequency light device or sunlight
etc., as it may affect the sensing performance.
If the surface of the sensing object has a shine,
mount the sensor inclining approx. 10 to 15 degrees
against the sensing object.
Do not touch the lens of the sensor by hand directly. If
the lens becomes dirty, wipe it off with a soft cloth gently.
When the inside lens is steamed up, unscrew the lens to get rid of the condensation.
For
LX-101
-D-Z, be sure to use the optional cable with connector.
Extension up to total 100m is possible with 0.3mm2, or more, cable.
However, in order to reduce noise, make the wiring as short as possible.
This sensor is suitable for indoor use only.
Do not use this sensor in places having excessive vapor, dust, etc., or
where it may come in direct contact with water, or corrosive gas.
Take care that the product does not come in contact with water, oil,
grease, or organic solvents, such as, thinner, etc.
Make sure that stress by forcible bend or pulling with 76N, or more, force
is not applied to the sensor cable joint.
This sensor cannot be used in an environment containing inflammable
or explosive gases.
Never disassemble or modify the sensor.
□ mounting
• Care must be taken regarding the
sensor mounting directrion with
respect to the object's direction of
movement.
Good Not good
Do not make the
sensor detect an
object in this di¬
rection because it
may cause unsta¬
ble operation.
Sensor mounting
bracket
MS-LX-1
(Optional)
□ PART DESCRIPTION
Digital display (Red)
□ I/O CIRCUIT DIAGRAMS
• NPN output type
Terminal No. of Connector Color code of cable type / cable with
Notes: 1 )The output 2 is not incorporated to connector type LX-101 D-Z.
2)The current of the connector type LX-101 D-Z is 100mA.