LIVARNO home 407982-2207 Installation Instructions Manual page 18

Assembly
6
Fig. :
A
• Tap the component with the narrow side in the profile
B
• Tap the component with the wide side in the profile
C
• Tap the component with the narrow side in the profile
D
• Tap the component with the wide side in the profile
CAUTION! The bending angle must be pushed into the profile and not
below it!
7
Fig. :
A
• Tap the component with the wide side in the profile
B
• Tap the component with the narrow side in the profile
C
• Tap the component with the wide side in the profile
D
• Tap the component with the narrow side in the profile
8
Fig. :
• Push the narrow profiles into the wide profiles such that subse-
quently, each of the short and the long bending angles point in
the same direction
9
Fig. :
• Slide the horizontal profiles to the width X-2 mm
• Slide the vertical profiles to the height Y-5 mm CAUTION! Meas-
ure X from the outer edge & Y from the inside of the
bending angle!
10
Fig. :
• Measure the length E of the narrow, vertical profiles
• Measure the length F of the narrow, horizontal profiles
11
Fig. :
• Shorten the clip profile 2x
• Shorten the clip profile 2x
CAUTION! Shorten the profiles such that each of the cut edg-
es subsequently lies in the direction of the corner connector.
12
Fig. :
• Clip the shortened clip profiles E along the projection of the nar-
row, vertical profiles
• Clip the shortened clip profiles F along the projection of the nar-
row, horizontal profiles
13
Fig. :
13
• Lay out the fabric straight on the frame
14
Fig. :
14
• Press in the handles with the short side down opposite on the
sides of the vertical profiles into the inner grooves above the fabric
15
Fig. :
8
• Press in the beading
the inside grooves over the fabric and handles
16
Fig. :
• Cut off the protruding fabric with a cutter knife. CAUTION! RISK
OF INJURY! Be careful when using the cutter knife.
17
Fig. :
7
• Push the brush via the corner connectors into the outer brush
channel, and shorten each of the projections
18
Fig. :
• First push the insect guard window with the bending angles
C
up below the blind frame
• Now push the insect
B
ing angles &
18 | EN
1
to the length E
2
to the length F
9
with the beading cutter around into
guard window with the
D
down over the blind
The
CAUTION!
3 up & the short ones
that the bending angles are hooked in at a 90° angle
5
3
• Cleaning
5
Use only a damp cloth with mild detergent for cleaning. You can
remove dust from the fibreglass fabric with a vacuum cleaner (brush
attachment) or hand broom.
• Storage
Store the product dry and clean in a temperature-controlled room
6
when not in use.
4
• Disposal instruction
6 Don't forget about environmental protection. There is a public take-
back system for the disposal of packaging materials and old appli-
4
ances. You can get information about collection points and current
regulations from your city or municipal administration.
• Liability
In the case of non-observance of the instructions and information
given in this manual, in the case of improper use or use outside the
intended purpose, the manufacturer rejects the warranty for damage
to the product. Liability for consequential damage to elements of any
kind or persons is excluded.
• Warranty
The product has been carefully produced according to strict quality
guidelines and conscientiously tested before delivery. In the event of
defects in this product, you have legal rights against the seller of the
product. These statutory rights are not limited by our warranty set out
below.
This product comes with a 3 year warranty from the date of purchase.
The warranty period begins on the date of purchase. Please keep the
original receipt in a safe place. This document is required as proof
of purchase.
If a material or manufacturing defect occurs within three years from
the date of purchase of this product, we will replace the product,
free of charge for you, with a product of our choice. In this case,
the warranty period starts afresh (valid only in Poland and Portugal).
This warranty is void if the product is damaged, improperly used or
maintained.
The warranty covers material or manufacturing defects. This warranty
does not cover product parts that are subject to normal wear and tear
(e.g. weathering) and can therefore be considered wear parts or for
damage to the fabric that has been torn by heavy use (stretching or
sharp objects).
• Manufacturer/Service
bash-tec GmbH
Hoorwaldstr. 42
DE-57299 Burbach
GERMANY
service@bash-tec.com
IAN 407982_2207
For all inquiries, please have the receipt and item number (e.g. IAN
12345) available as proof of purchase.
Note: The pictures in this manual are exemplary and may differ from
the product.
A
&
bend-
frame
10
long bending angles
11
must point down.
• Download assembly manual
At www.lidl-service.com you can download
these and many other manuals, product vid-
eos and installation software.
This QR code will take you directly to the Lidl
service page (www.lidlservice.com) and you
can open your manual by entering the article
number (IAN) 407982_2207.
must point
Make sure